Table of Contents
Advertisement
Available languages
Available languages
*) AU:
Guld, Gold or Oro
l = max. 15 m
Sair, S5=
NTC 5000 Ω @ 25°C, M2020 (Danfoss type=EKS 211) /
NTC 10000 Ω @ 25°C, Beta 3435 (Danfoss type=EKS 221) /
NTC 3000 Ω @ 25°C /
NTC 2500 Ω @ 0°C /
NTC 10000 Ω @ 25°C /
NTC 2000 Ω @ 25°C
Type
NTC 5000 Ω
@ 25°C
(M2020)
Danfoss NTC =
EKS 211
°C
Ω
30
4029
5000
25
20
6246
15
7855
10
9951
5
12696
0
16330
−5
21166
−10
27681
−15
36503
−20
48614
−25
65333
−30
88766
−35
121795
−40
169157
Alternativer
Alternatives
Alternativen
Alternatives
Alternativas
o06
n01
2
*)
NTC 10000 Ω
NTC 3000 Ω
@ 25°C
@ 25°C
(Beta 3435)
EKS 221
Ω
8313
10000
12091
14695
17958
22068
27278
33922
42450
53468
67801
86580
111364
144324
188500
Carel:
Frigo:
HP/WF/WP/INF
M841
Dixell:
NS/NG/NX/NY/NT
Eliwell:
SN8
Lae:
SN4K..P
n02
Instructions RI8PN253 © Danfoss 03/2012
NTC 2500 Ω
@ 0°C
-
-
Ω
Ω
2417
-
3000
883
3747
1074
4712
1313
5970
1616
7617
2000
2492
9798
12700
3124
16608
3947
21902
5019
29168
6434
39200
8306
53259
10822
73077
14217
101490
18848
Wurm:
TRK 277
n03
n04
*)
NTC 10000 Ω
NTC 2000 Ω
@ 25°C
@ 25°C
-
-
Ω
Ω
8300
1651
10000
2000
12271
2437
15146
2987
18809
3682
23504
4571
29564
5716
37441
7198
47754
9133
61357
11644
79440
14961
103676
19402
136428
25388
181078
33505
242495
44657
Wurm:
Lae:
T2000
SN2K..P
n05
n06
EKC 202C-MS
- Quick Links:
- Diagrams
- Set Temperature
- Set Menu
- The Buttons
- Start-Up
- Les Boutons
- Mise en Route
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the EKC 202C-MS and is the answer not in the manual?
Questions and answers
New danfoss ref control showing -40c but I want just +2c to +6c how I calibrated
To calibrate the Danfoss EKC 202C-MS controller to display and control temperatures between +2°C and +6°C, follow these steps:
1. Access the Programming Mode:
- Press and hold the [SET] button for 5 seconds until the display shows "PAS" (password).
- Enter the password (default is often "1234") using the up/down arrows.
- Press [SET] to confirm.
2. Set Temperature Range:
- Navigate to parameter r01 (Setpoint) and set it to the desired midpoint (e.g., +4°C).
- Go to r02 (Differential) and set it to 2°C. This creates a control range of +2°C to +6°C (±2°C from setpoint).
- Press [SET] to confirm each value.
3. Verify Sensor Calibration (if needed):
- Check parameter r05 (Sensor offset) to ensure temperature readings are accurate. Adjust if the displayed temperature is consistently off.
4. Exit Programming Mode:
- Press and hold [SET] for 5 seconds or wait for the controller to time out.
The controller will now regulate the temperature between +2°C and +6°C.
This answer is automatically generated