TERK Technologies TV44 Owner's Manual
Amplified/outdoor satellite dish clip-on antenna
Hide thumbs
Also See for TV44:
- Owner's manual (14 pages) ,
- Specification sheet (2 pages) ,
- Owner's manual (9 pages)
Related Manuals for TERK Technologies TV44
Summary of Contents for TERK Technologies TV44
- Page 1 All manuals and user guides at all-guides.com TV44 Owner’s Manual Amplified/Outdoor Satellite Dish Clip-on Antenna...
-
Page 2: Safety Precautions
All manuals and user guides at all-guides.com Safety Precautions Warning! Use extreme caution when installing or removing an outdoor antenna that is located close to overhead wires such as power lines, telephone lines or cable TV lines. If any part of the antenna makes contact with overhead power lines, touching the antenna or the antenna cable can cause electrocution and death. - Page 3 Before you begin Please take a moment to familiarize yourself with the various elements in the TV44 package. Please make sure that your package includes all of the necessary pieces (see Fig 1). If you believe your box is missing any pieces, please call TERK Technical Support at 1(800) 942-TERK (8325).
- Page 4 All manuals and user guides at all-guides.com Installing the TV44 on a satellite dish 1. Make sure all satellite receivers are turned off and unplugged from the electrical outlet. 2. Unsnap the antenna from the back notch of the mounting clamp.
- Page 5 6. Tighten the clamps by turning the thumb-wheel screw clockwise. Note: We recommend the use of the enclosed security clips for any dish 20” or larger. Snap the security clips onto the TV44 and slide down towards the mounting clips. See Fig 5. Fig 5...
- Page 6 All manuals and user guides at all-guides.com Connecting the TV44 Depending on the type of satellite dish you have, go to one of the following five scenarios to determine how to connect the TV44 antenna to your satellite dish. A-Single LNB (Phase1) Satellite Dish 1.
- Page 7 5. Reconnect the LNB to the dish arm. See Fig 8. Fig 8. 6. Connect the remaining end of the 2 black 32” antenna cables to the IN 1 and IN 2 terminals on the TV44 antenna. See Fig 9. Logo Side Dish Side Fig 9.
- Page 8 See Fig 10. 3. Connect the satellite cables to the terminals marked OUT 1, OUT 2, OUT 3, and OUT 4 on the TV44 antenna. See Fig 11. Logo Side Dish Side Fig 11.
- Page 9 See Fig 12. Fig 12. 6. Connect the remaining end of the 4 black 32” antenna cables to the IN 1, IN 2, IN 3 and IN 4 terminals on the TV44 antenna. See Fig 13. Logo Side Dish Side Fig 13.
- Page 10 Dish Side Fig 14. 3. Using 4 black 32” antenna cables, connect the IN 1, IN 2, IN 3, and IN 4, terminals of the TV44 to the “OUTPUT” or “TO RECEIVER” terminals on your multiswitch. See Fig 15. Logo Side Dish Side Fig 15.
- Page 11 All manuals and user guides at all-guides.com D- Using a Multiswitch with an Antenna Input 1. Complete “Scenario A” instructions. (Page 5) 2. Locate your multiswitch and disconnect the satellite wire from the 18 volt or Satellite A/101 18 volt terminal. 3.
- Page 12 RG6 coaxial cable if they are not long enough. 3. Using 2 black 32” antenna cables connect the “TO RECIEVER” terminals on the SW21 multiswitches to the IN 1 and IN 2 terminals on the TV44 antenna. See Fig 18. Logo Side Fig 17.
- Page 13 All manuals and user guides at all-guides.com Installing the indoor diplexers 1. Disconnect the satellite cable from the “SAT IN” terminal on your satellite receiver. See Fig 19 . Fig 19. 2. Connect the satellite cable to the terminal marked “TV/SAT” on the indoor diplexer.
-
Page 14: Setting Up Your Tv
For more information, visit www.terk.com. or, for technical support, call 1.800.942.TERK (8375). 78P008A TERK is a registered trademark. The TERK logo is a trademark of the TERK Technologies Corp.
Need help?
Do you have a question about the TV44 and is the answer not in the manual?
Questions and answers