Advertisement
FY Remote Control (Optional Item)
5
Function
Interface
Tip：The Remote Control will be
automatically powered off to
save battery if there is no operation
within three minutes.
Wireless Remote Control
Steps to connect wireless remote control:
1
Open the wireless remote control: Long press the function button on
wireless remote control for one second to power on.
2
Install the receiver for wireless remote control: Insert the receiver for
wireless remote control into the function port of gimbal .
3
Open the gimbal: Long press the function button on gimbal for two
seconds to turn on the gimbal.
4
Use the wireless remote control to control the gimbal.
Connect the Micro interface of wireless remote control with
Charging
5V charger by USB cable.
Remote Control Distance
15 meters in an open environment.
Match Code
Keep the gimbal powered on, restart the remote control
and connect the receiver of RC to the gimbal, press the remote control
function button for 7 times in 5 seconds, if the indicator on the RC flashes
5 times it means the receiver and the transmitter of RC match successfully,
then customer can control the gimbal by the RC.
▲ RC needs to be match code whenever the following situations：（1）Connecting properly but still control in fail.
Firmware Upgrade
6
Firmware Upgrade Instruction
Please visit the official website of Feiyu Tech: www.feiyu-tech.com to download the USB driver, firmware upgrade software and the latest firmware.
Unzip the compressed file locally to your computer. Refer to the connection diagram on how to connect the gimbal with the computer. Please
follow the instructions inside the firmware upgrade package carefully, or there will be a risk of rendering the gimbal inoperable.
Attention : Please make sure that the connection to the computer is done by the USB connector.
Tilt and Level Calibration
The tilt and level settings can be calibrated through the use of the configuration software. User can adjust the tilt and diagonal rotation in small intervals
to better adapt to his/her filming scene. Before any calibration, please insert the batteries into the gimbal and refer to the connection diagram to
connect the gimbal with the computer.
Attention : Please make sure that the connection to the computer is done by the USB connector.
Video and Camera Charging Interface
7
This interface can be output 5 voltage and receive analog video signal from GoPro
Connect the video output and camera charging cable as the above diagram
can power the GoPro camera and view video signal from the GoPro camera.
Initialize The Gimbal
8
FY WG needs to be initialized whenever the
following situations are observed after power on
1. The tilt angle is not leveled with the horizontal
surface.
2. The roll angle is not parallel to the horizontal
surface.
3. When the gimbal is Full-Axis-Lock mode,
the camera does not stay stationary..
FY WG 3-Axis Wearable Gimbal is a feature-rich camera stabilizer, yet lightweight and portable.
It is prohibited for any user to use the gimbal for any illegal purposes.
Guilin Feiyu Electronic Technology Co.,Ltd and our associates assume no liability for any accident, injury,
death, loss, or other claim related to or resulting from the use of this product. In no event shall Guilin Feiyu
Electronic Technology Co.,Ltd and our associates be liable for incidental or consequential damages relating
to or resulting from the use of this product or any of its parts. Damage resulting from use, accident, or normal
wear and tear is not covered by our warranty.
Guilin Feiyu Electronic Technology Co.,Ltd reserves the right to amend this manual and the terms and
conditions of this product at any time.
Receiver
for wireless
remote control
!
Wireless
Please install
remote control
the receiver
properly before
power on
Be sure to insert the
!
batteries before upgrading
Function
USB Cable
Interface
Initialization Instructions
1. Ensure gimbal is fully assembled and camera
is installed properly.
2. Place the gimbal on a flat surface and keep it
stationary.
3. Power on the Gimbal.
4. Wait for the gimbal to finish its initialization
before resuming the use of the gimbal.
Note:
When initialization is completed,
the LED light will quickly flash.
D I S C L A I M E R
With the remote control, you can switch the gimbal mode or adjust the angle from a distance.
Joystick
Function
Button
Power on / off
Operation
Power
Long press for
ON
0.5 second
Long press for
OFF
3 seconds
Operation
Explanation
Single Tap
Mode #1 Panning Mode
Double Tap
Mode #2 Panning and Tilting Mode
Triple Tap
Inversion Mode
Quadruple Tap
Reset
Tap Button
Calibration Using Remote Control
Six Times
Tap Button
Match Code Mode
Seven Times
Long Press
Mode #3 Lock Mode
For 1 Second
Long Press
Turn Off The Gimbal
For 3 Second
Note: The function button on the Gimbal will be disabled after connect the Remote Control
!
WARNING
Make sure that the
connec�on to the
computer is done by the
USB Connector
Function
Interface
Video Output Cable
After connecting the video output and camera charging
cable, the analog monitor can be used as a display.
Note: The Analog Monitor are equipped by users.
Please visit the official website of Feiyu Tech
to get related information: www.feiyu-tech.com
Technical support: service@feiyu-tech.com
Function
USB Data Cable for RC
Interface
Direction Button
UP
DOWN
LEFT
Remote Control Operation Instructions
Remark
Triple tap again
Single tap ,exit calibration and enter standby. Wake the
gimbal by pressing the function button once again
Match code when connecting properly but still control
Wireless RC
in fail or change the receiver/wireless remote control.
（2）Change the receiver or wireless remote control.
Parameters
Upgrade........
PC
Working Voltage
Vertical Tilting Angle
Rolls Angle
Horizontal Panning Angle
Tilting Increments
Panning Increments
Analog Monitor
(
Equipped by users
)
Static Attitude
Tracking Accuracy
Motion Attitude
Tracking Accuracy
Overload Current
Protection
Weight
Usage Time
Camera Maximum Height
Camera Maximum Thickness
Camera Maximum Weight
Motionless Flat Surface
Please assemble the gimbal in accordance to
Everyone
the diagram provided.
Can Make a Movie
Please upgrade the firmware and configuration
settings with the provided USB data cable.
Please charge the battery with the provided
battery charger.
Please install the camera securely before
powering on the gimbal.
Wired remote control
Function
Button
Direction
Button
RIGHT
,exit inversion mode into original status
53.4 mm
35 mm
95 mm
6.0 V ~ 9 V
320°
100°
320°
2°/S ~ 75°/S
3°/S ~ 150°/S
0.01 ~ 0.05
(
Working Voltage
0.1 ~ 0.5
(
Motor Overload<2G
800 mA
188 g (
Without
Batteries & Camera
3 ~ 4 Hours
43.6 mm
( Replaceable
mounting bracket )
31.7 mm
( Replaceable
mounting bracket )
150 g
A T T E N T I O N
)
)
)
Advertisement
