Feiyu FY WG Manual

FY WG 3 Axis Wearable Gimbal is compatible with GoPro HERO4 / 3+ / 3 and cameras with
similar dimensions. Reserved mounting space for GoPro LCD Touch BacPac
Introduction
1
FY WG is a lightweight, yet feature-rich, wearable 3 axis gimbal capable of capturing immersive and fully stabilized footages. It is
compatible with GoPro HERO4/ 3+/ 3 (with optional mounting space for GoPro LCD BacPac) and other cameras with similar dimensions.
The FY WG is a miniaturized version of the best-selling FeiYu gimbal, offering exceptional stabilization technology in a wearable form factor
for action cameras. A GoPro T-Clamp adapter is packaged with every FY WG. Users can attach the gimbal to any accessories supporting
the GoPro three-prong mount. The FY WG also contains two 1/4"-20 tripod mounts on its gimbal body, allowing the gimbal to be mounted
in different orientations to all universal tripod screw mount accessories (including helmets, bikes, selfie sticks and other accessories).
Install
2
Camera In Left
Camera in Right
Operation
3
Function Switch between different operating modes by pressing the function button.
Function
Button Button The LED light will flash distinctively to indicate different operating modes.
Operating Modes and Functions
Operating Modes and Functions
- Panning Mode
Mode #1
Camera is permitted to pan left or right. Vertical tilts or rolls are restricted.
- Panning and Tilting Mode
Mode #2
- Lock Mode
Camera stays in its current orientation. All panning, tilting and rolls are restricted.
Mode #3
Inversion Mode Pressing the function button three consecutive times in any operating mode, the gimbal will switch to the
Inverted Mode (Allowing the user to flip the gimbal orientation upside down). Pressing the function button three more times
while in Inverted Mode to switch back to the original orientation
Manual Pulling Locking After the gimbal has been powered on for eight seconds, the tilt angle can be adjusted manually in the Panning Mode
and the Lock Mode. Adjust the title angle to the desired position and wait for 0.5 second until the gimbal registers the new angle.
Reset Pressing the function button four consecutive times will reset the gimbal to initial orientation.
By using the optional G4 Remote Control, tilt and level can be adjusted without the need to connect to a computer.
Tilt and Level Calibration
For more information, please refer to G4 Remote Control section in the instruction manual.
Panning Speed Adjustment
By using the optional G4 Remote Control, the follow speed of panning can be adjusted without the need to connect
to a computer. For more information, please refer to the G4 Remote Control section in the instruction manual.
Operation LED Status
Single Tap LED Flashes Once
Double Tap LED Flashes Twice
Triple Tap LED Flashes Once
Quadruple Tap LED Flashes Once
* When the gimbal is in the Inverted Mode, pressing the function button three consecutive times will revert back to the original orientation.
When the battery is low, the gimbal will make three beeping sound and automatically shut down itself.
Accessories
4
Charger
Rechargeable
Input: DC 5V Min 800mA
Battery
Output: DC 4.2V
Type: 18350
STEP 1
Remove the screws on the
battery compartment,
insert two16340 batteries
and tighten the screws.
!
WARNING ! WARNING !
Do not power on the Do not power on the
gimbal before completing gimbal before completing
all the installation steps. all the installation steps.
STEP 2
Mount the camera carefully
to the mounting bracket
and tighten the screws.
Ensure the camera is mounted securely. Press and hold the function button
POWERING
for 2 seconds. The LED light will turn blue.
ON / OFF
Press the function button and hold for 3 seconds, it will be powered off.
Vertical
Camera In Left
Camera is permitted to pan left or right and tilt up and down. Rolls are restricted.
Function Button Quick Reference
Function Explanation Operation
Long Press
Panning Mode
For 1 Second
Panning and Tilting Mode
Long Press
For 2 Second
Inversion Mode
Long Press
Reset For 3 Second
Hexagonal
Socket Head M 1.5 Allen Key
Cap Screw
M2*6mm
USB Connector USB Cable
Hexagonal Socket
Head Cap Screw
T-Clamp
STEP 3
The Gimbal can be mounted in two different ways. For use with GoPro
Accessories, mount the provided T-clamp to the side or the bottom of
the gimbal. Attach T-clamp to any accessories supporting the standard
GoPro three-prong mount. The gimbal can also be mounted directly to
other accessories using the standard 1/4" tripod mount. Tighten all
screws and ensure it is firmly mounted before using the gimbal.
Forward
Camera in Right
Camera In Left
Tilting
Function
Button
.
LED Status
On Constantly
Turn On And Switch To
The Mode's LED Status
Turn Off After
A moment
Long screw
T-Clamp
Curved Adhesive Quick-Release
Mounts Buckle
Accessories For
1/4 Inch Screws
Inverted
Camera in Right
Rolling
Panning
Sound Function
Lock Mode
Two Beeps Power On
Three Beeps Shutdown
Extension Knurled
Thumb Screw
3M Adhesive
Manual Version 1.0
Rolling Axis
Tilting Axis
Function
Interface
Function Button
（ ON / OFF ）
Panning Axis
Video And Camera
Charging Interface
Screws For
The Battery
Compartment
T-Clamp Screw Hole
1/4 Inch Screw Hole
T-Clamp
Screw Hole
T-Clamp
Screw Hole
1/4 Inch
Screw Hole
Charging
USB Cable
USB Power
Adapter
（Not Included）