Advertisement
Remote Control (Optional Item)
5
USB Data Cable For RC
Function
Interface
Remote Control Operation Instructions
Operation
Explanation
Single Tap
Mode #1 Panning Mode
Double Tap
Mode #2 Panning and Tilting Mode
Triple Tap
Inversion Mode
Quadruple Tap
Reset
Tap Button Six Times
Calibration Using Remote Control
Long Press
Mode #3 Full-Axis-Lock Mode
For 1 Second
Long Press
Turn Off The Gimbal
For 3 Second
Firmware Upgrade
6
Firmware Upgrade Instruction
Please visit the official website of Feiyu Tech: www.feiyu-tech.com to download the USB driver, firmware upgrade software and the latest firmware.
Unzip the compressed file locally to your computer. Remove the batteries and refer to the connection diagram on how to connect the gimbal with
the computer.Please follow the instructions inside the firmware upgrade package carefully, or there will be a risk of rendering the gimbal inoperable.
Attention : Please make sure that the connection to the computer is done by the USB connector.
Tilt and Level Calibration
The tilt and level settings can be calibrated through the use of the configuration software. User can adjust the tilt and diagonal rotation in small intervals
to better adapt to his/her filming scene. Before any calibration, please insert the batteries into the gimbal and refer to the connection diagram to
connect the gimbal with the computer.
Attention : Please make sure that the connection to the computer is done by the USB connector.
Panning Speed Adjustment
The panning speed can be adjusted through the use of the configuration software. User can adjust to the desired panning speed to better adapt to
his/her filming scene. There are three settings available: "SLOW", "NORMAL" and "FAST". Default setting is "NORMAL".
Attention : Please make sure that the connection to the computer is done by the USB connector.
Video And Camera Charging Interface
7
This interface can be output 5 voltage and receive analog video signal from GoPro
Connect the camera charging
cable to power the GoPro camera.
Initialize The Gimbal
8
FY WG needs to be initialized whenever the
following situations are observed after power on
1. The tilt angle is not leveled with the horizontal
surface.
2. The roll angle is not parallel to the horizontal
surface.
3. When the gimbal is Full-Axis-Lock mode,
the camera does not stay stationary..
A T T E N T I O N
Please assemble the gimbal in accordance to the diagram provided .
Please upgrade the firmware and configuration settings with the
provided USB data cable.
Please charge the battery with the provided battery charger.
Please install the camera securely before powering on the gimbal.
Angle Adjustment
In Panning Mode, tilt angle can be controlled by pressing the"UP"or
"DOWN"button on the Remote control. Pan angle can be controlled
by pressing the"LEFT"or"RIGHT"button on the Remote Control.
Function
Button
Panning Speed Adjustmen
Speed adjustment can be done in any operating mode. To increase
Direction
panning speed, hold the "RIGHT" button and quickly tap the function
Button
button four times. To decrease panning speed, hold the "LEFT" button
and quickly tap the function button four times. When adjustment is
completed, the gimbal automatically saves the current setting and
enters the standby mode. Press the function button once on the Remote
Remote
Control to wake the gimbal and resume operation. There are three
Control
settings available: "SLOW", "NORMAL" and "FAST". Default setting
is "NORMAL".
Operation Again
Other Operation Is Arbitrary
Other operation Is Arbitrary
Triple Tap Again
Other Operation Is Arbitrary
Single Tap Again
Other Operation Is Arbitrary
Be sure to remove the
!
batteries before upgrading
Function
USB Cable
Interface
Connect the video output cable to the
function interface to view video signal
from the GoPro camera.
Initialization Instructions
1. Ensure gimbal is fully assembled and camera
is installed properly.
2. Place the gimbal on a flat surface and keep it
stationary.
3. Power on the Gimbal.
4. Wait for the gimbal to finish its initialization
before resuming the use of the gimbal.
Note:
When initialization is completed,
the LED light will quickly flash.
FY WG 3-Axis Wearable Gimbal is a feature-rich camera stabilizer, yet lightweight and portable.
It is prohibited for any user to use the gimbal for any illegal purposes.
Guilin Feiyu Electronic Technology Co.,Ltd and our associates assume no liability for any accident, injury, death, loss, or other
claim related to or resulting from the use of this product. In no event shall Guilin Feiyu Electronic Technology Co.,Ltd and our
associates be liable for incidental or consequential damages relating to or resulting from the use of this product or any of its
parts. Damage resulting from use, accident, or normal wear and tear is not covered by our warranty.
Guilin Feiyu Electronic Technology Co.,Ltd reserves the right to amend this manual and the terms and conditions of this
product at any time.
Explanation
Exit inversion mode into original status
Exit calibration and enter standby.
Wake the gimbal by pressing the
function button once again
!
WARNING
Make sure that the
connection to the
computer is done by the
USB Connector
Function
Analog Monitor Cable
Interface
(
)
Equipped By Users
After connecting the video output cable, the analog
monitor can be used as a display.
Note:
The video output cable is not included in the
standard package. It is an optional purchase.
Tilt and Level Calibration
Using the Remote Control, tilt and level
can be adjusted without the need to
connect to a computer. Calibration
can be done in any operating mode.
Quickly tab the function button six times
to enter the calibration mode. Tilt angle
can be controlled by pressing the
"UP" or "DOWN" button. Pan angle
can be controlled by pressing the
"LEFT" or "RIGHT" button. When
calibration is completed, the gimbal
automatically saves the current setting
and enters the standby mode. Press the
function button once on the Remote
Control to wake the gimbal and
resume operation.
Note: Please make sure gimbal
completed initialization successfully
before attempting calibration.
Direction Button
UP
Operation
DOWN
Hold the "LEFT"
button and
LEFT
press the function
button four times
RIGHT
Hold the "RIGHT"
NOTE
button and
The function
press the function
button on the
button four times
Gimbal will be
disabled after
connect the
Remote Control
Parameters
Upgrade........
PC
Working Voltage
Vertical Tilting Angle
Rolls Angle
Horizontal Panning Angle
Analog Monitor
Tilting Increments
(
)
Equipped By Users
Panning Increments
Static Attitude
Tracking Accuracy
Motion Attitude
Tracking Accuracy
Overload Current
Protection
Weight
Usage Time
Camera Maximum Height
Camera Maximum Thickness
Camera Maximum Weight
Motionless Flat Surface
D I S C L A I M E R
Explanation
Increase the follow
speed of the heading.
Gimbal will then enter
the standby Mode
Decrease the follow
speed of the heading.
Gimbal will then enter
the standby Mode
Press the function button again
to wake the gimbal from standby
53.4 mm
35 mm
95 mm
6.0 V ~ 9 V
320°
100°
320°
2°/S ~ 75°/S
3°/S ~ 150°/S
0.01 ~ 0.05
(
)
Working Voltage
0.1 ~ 0.5
(
Motor Overload<2G
800 mA
188 g (
Without
)
Batteries & Camera
3 ~ 4 Hours
43.6 mm
31.7 mm
150 g
)
Advertisement
