Accepting Payments; How To Swipe Magnetic Stripe Cards; How To Insert Contact Chip Cards; How To Tap Contactless Cards / Devices - Magtek iDynamo 6 Quick Installation Manual

Compliance

FCC INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by MagTek could void the user's authority to operate this equipment.
CE STANDARDS
Testing for compliance with CE requirements was performed by an independent laboratory. The unit under test was found compliant
with standards established for Class B devices.
UL/CSA
This product is recognized per UL 60950 1, 2nd Edition, 2011 12 19 (Information Technology Equipment - Safety - Part 1: General
Requirements), CSA C22.2 No. 60950 1 07, 2nd Edition, 2011 12 (Information Technology Equipment - Safety - Part 1: General
Requirements).
ROHS STATEMENT
When ordered as RoHS compliant, this product meets the Electrical and Electronic Equipment (EEE) Reduction of Hazardous
Substances (RoHS) European Directive 2002/95/EC. The marking is clearly recognizable, either as written words like "Pb-free," "lead-
free," or as another clear symbol ( ).
Legal
"Made for iPhone" and "Made for iPad" mean that an electronic accessory has been designed to connect specifically to iiPhone or
iPad respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the
operation of this device or its compliance with safety and regulatory standards.
iPhone and iPad are trademarks of Apple Inc., registered in the U.S. and other countries.
iPhone and iPad not included.
Apple®, Apple Pay®, OS X®, iPhone®, iPad®, iPad Air®, iPad Pro®, Lightning®, and Mac® are trademarks of Apple Inc., registered in the U.S. and other countries. EMV® is a registered trademark
in the U.S. and other countries and an unregistered trademark elsewhere. The EMV trademark is owned by EMVCo, LLC. The Contactless Indicator mark, consisting of four graduating arcs,
is a trademark owned by and used with permission of EMVCo, LLC.

Accepting Payments

If the solution design includes accepting contactless payments while iDynamo 6
is powered by a hand-held host, the device must have the battery pack installed.
iDynamo 6 only uses the battery pack to power its on-board contactless reader,
and receives all other operating power from the connected host.

How to Swipe Magnetic Stripe Cards

Cardholders should swipe magnetic stripe cards in the MSR swipe path with
the magnetic stripe facing away from the cardholder and into the device.
Cardholders may swipe in either direction along the path.

How to Insert Contact Chip Cards

Cardholders should insert chip cards into the chip card slot with the chip facing
the cardholder and toward the slot.

How to Tap Contactless Cards / Devices

If the cardholder is using an electronic payment device, such as a smartphone,
make sure the payment device has NFC turned ON and has a payment app
configured to process transactions. Wait until the host software indicates it is
ready for a tap. Tap the card or electronic payment device on the contactless
landing zone, indicated by the EMVCo Contactless Indicator on the device's face.
The card or device must be centered over the contactless landing zone. Wait
for the device to beep. The host software may also display progress showing
whether the tap succeeded or failed. Because each smartphone model may
have its NFC antenna placed differently, the ideal tap position may vary by make
and model. For example, Samsung users may need to center the phone on the
contactless landing zone, while iPhone users may need to tap the top of the
phone on the contactless landing zone. Remove the card or electronic payment
device from the contactless landing zone.
Pb
MagTek ® Inc., 1710 Apollo Court, Seal Beach CA 90740 p 562-546-6400 | support: 651.415.6800 | support@magtek.com
MAGTEK: Registered to ISO 9001:2015 © Copyright 2019 MagTek, Inc. PN D998200327 rev. 10 8/19