Advertisement
154574-00/2610-220
5/17/02
1:45 PM
Safety Instructions For All Tools
•
KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
•
CONSIDER WORK AREA ENVIRONMENT. Don't expose power tools to rain.
Don't use power tools in damp or wet locations. Keep work area well lit. Do not
use tool in presence of flammable liquids or gases.
•
GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded
surfaces. For example; pipes, radiators, ranges, and refrigerator enclosures.
•
KEEP CHILDREN AWAY. Do not let visitors contact tool or extension cord. All
visitors should be kept away from work area.
•
STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high
or locked-up place — out of reach of children.
•
DON'T FORCE TOOL. It will do the job better and safer at the rate for which it
was intended.
•
USE RIGHT TOOL. Don't force small tool or attachment to do the job of a heavy-
duty tool. Don't use tool for purpose not intended.
•
DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught
in moving parts. Rubber gloves and non-skid footwear are recommended when
working outdoors. Wear protective hair covering to contain long hair.
•
USE SAFETY GLASSES. Also use face or dust mask if operation is dusty.
•
DON'T ABUSE CORD. Never carry tool by cord or yank it to disconnect from
receptacle. Keep cord from heat, oil, and sharp edges.
•
SECURE WORK. Use clamps or a vise to hold work. It's safer than using your
hand and it frees both hands to operate tool.
•
DON'T OVERREACH. Keep proper footing and balance at all times.
•
MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories.
Inspect tool cords periodically and if damaged, have repaired by authorized
service facility. Inspect extension cords periodically and replace if damaged.
Keep handles dry, clean, and free from oil and grease.
•
DISCONNECT OR LOCK OFF TOOLS when not in use, before servicing, and
when changing accessories, such as blades, bits, cutters.
•
REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see
that keys and adjusting wrenches are removed from tool before turning it on.
Page 1
•
AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be
sure switch is off when plugging in.
•
EXTENSION CORDS. Make sure your extension cord is in good condition. When
using an extension cord, be sure to use one heavy enough to carry the current
your product will draw. An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. The following table shows the
correct size to use depending on cord length and nameplate ampere rating. If in
doubt, use the next heavier gage. The smaller the gage number, the heavier the
cord.
•
OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only
extension cords intended for use outdoors and so marked.
•
STAY ALERT. Watch what you are doing. Use common sense. Do not operate
tool when you are tired.
•
CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part
that is damaged should be carefully checked to determine that it will operate
properly and perform its intended function. Check for alignment of moving
parts, binding of moving parts, breakage of parts, mounting, and any other
conditions that may affect its operation. A guard or other part that is damaged
should be properly repaired or replaced by an authorized service center unless
otherwise indicated elsewhere in this instruction manual. Have defective
switches replaced by authorized service center. Do not use tool if switch does
not turn it on and off.
1
Minimum Gage for Cord Sets
Volts
Total Length of Cord in Feet
120V
0-25
26-50
51-100
240V
0-50
51-100
101-200
Ampere Rating
More
Not more
AWG
Than
Than
0
-
6
18
16
16
6
-
10
18
16
14
10
-
12
16
16
14
12
-
16
14
12
Not Recommended
101-150
201-300
14
12
12
Advertisement
