Cat # Voltage Pack Style Capacity Please take time to read this manual and pay particular attention to the safety rules we’ve provided for your protection. Don’t forget to send in your owner’s 2755 9.6V 3/8" Standard 0-400/0-1100 Standard registration card. If you have any questions about your tool please call:...
FOR YOUR SAFETY- ALL TOOLS safe performance. Follow instructions for lubricating and changing accessories. Keep handles dry, clean, and free from oil and grease. W W A A R R N N I I N N G G : When using electric tools, basic safety precautions should always be 12.
Battery Packs Battery Chargers (98014, 97014 & 98020) Your tool uses a 9.6 Volt, a 12.0 Volt, or a 14.4 Volt battery pack. When Your battery can be charged in the 9 9 8 8 0 0 1 1 4 4 , , 9 9 7 7 0 0 1 1 4 4 (1 Hour Chargers) or the ordering replacement battery packs, be sure to include catalog number and 9 9 8 8 0 0 2 2 0 0 (15 Minute Charger).
SAFETY RULES FOR CHARGERS CHART FOR MINIMUM WIRE SIZE (AWG) OF EXTENSION CORDS NAMEPLATE RATING AMPS - 0 - 10.0 1. Before using charger, read all instructions and cautionary markings on (1) Total Extension Cord Length (feet) 50 75 100 125 150 175 charger, (2) battery pack, and (3) product using battery pack.
SAFETY RULES FOR BATTERIES 6. Charge the battery packs listed on page 2 only in Univolt™ or Cyclone Series™ chargers. The batteries in your new battery pack are not fully charged out of the 7. N N O O T T E E : : Review and observe all of the “Important Charging Notes” in the carton! First read the safety instructions below.
Charging Procedure battery pack fresh and fully charged. N N O O T T E E : A battery pack will slowly lose 9 9 8 8 0 0 1 1 4 4 / / 9 9 7 7 0 0 1 1 4 4 ( ( 1 1 H H o o u u r r C C h h a a r r g g e e r r s s ) ) o o n n l l y y its charge when kept out of the 1.
IMPORTANT CHARGING NOTES Under certain conditions, with the charger plugged into the power supply, the exposed charging contacts inside the charger can be 1. Longest life and best performance can be obtained if the battery pack is shorted by foreign material. Foreign materials of a conductive nature charged when the air temperature is between 65°F and 75°F (18°- such as, but not limited to, steel wool, aluminum foil, or any buildup of 24°C).
TOOL OPERATION Removing and Installing the Battery Pack N N O O T T E E : : Y Y O O U U R R B B A A T T T T E E R R Y Y P P A A C C K K W W I I L L L L N N O O T T B B E E F F U U L L L L Y Y C C H H A A R R G G E E D D O O U U T T O O F F T T H H E E To turn the tool “ON,”...
Forward/Reverse Control Button Torque Adjustment Collar A forward/reverse control button determines the direction of the tool and Your driver/drill has an adjustable torque screwdriver mechanism for driving also serves as a “lock off” button. To select forward rotation, release the and removing a wide array of fastener shapes and sizes.
Chuck Removal Operation as a Drill Turn the collar to the drill bit symbol. Install and tighten the desired drill bit A A l l w w a a y y s s w w e e a a r r e e y y e e p p r r o o t t e e c c t t i i o o n n . . in the chuck.
MAINTENANCE Drilling in Wood Holes in wood can be made with the same twist drills used for metal. These CLEANING: With the motor running, blow dirt and dust out of all air vents bits may overheat unless pulled out frequently to clear chips from the flutes. with dry air at least once a week.
IMPORTANT! E E v v e e r r y y B B & & D D t t o o o o l l i i s s o o f f t t h h e e h h i i g g h h e e s s t t q q u u a a l l i i t t y y . . To assure product safety and reliability, particularly for Double Insulated tools, I I f f y y o o u u w w i i s s h h t t o o c c o o n n t t a a c c t t u u s s r r e e g g a a r r d d i i n n g g t t h h i i s s p p r r o o d d u u c c t t , , p p l l e e a a s s e e c c a a l l l l t t o o l l l l repairs, maintenance and adjustment (excluding maintenance described in...