Advertisement

Quick Links

Model:
8000TVC
WARNING
IF THE INFORMATION IN THESE
INSTRUCTIONS IS NOT
FOLLOWED EXACTLY, A FIRE OR
EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE,
PERSONAL INJURY, OR DEATH.
- Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
- What to do if you smell gas
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the
fire department.
- Installation and service must be performed by a
qualified installer, service agency, or the gas
supplier.
This product is covered by one or more of the following patents: (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792; 4,520,791; 4,793,322;
4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254 5,191,877; 5,218,953; 5,328,356; 5,429,495; 5,452,708; 5,542,407; 5,613,487; (Australia)
543790;586383; (Canada) 1,123,296; 1,297,746; 2,195,264; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign pate nts pending.
All manuals and user guides at all-guides.com
Heat-N-Glo
Installers Guide
READ THIS MANUAL BEFORE INSTALLING
OR OPERATING THIS APPLIANCE. THIS
INSTALLERS GUIDE MUST BE LEFT WITH
THE APPLIANCE FOR FUTURE REFERENCE.
WARNING: IMPROPER
INSTALLATION, ADJUSTMENT,
ALTERATION, SERVICE OR
MAINTENANCE CAN CAUSE INJURY
OR PROPERTY DAMAGE. REFER TO
THIS MANUAL. FOR ASSISTANCE OR
ADDITIONAL INFORMATION
CONSULT A QUALIFIED INSTALLER,
SERVICE AGENCY, OR THE GAS
SUPPLIER.
Underwriters
Laboratories Listed
258-900C 10/99

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Heat-N-Glo 8000TVC and is the answer not in the manual?

Questions and answers

Summary of Contents for Hearth Technologies Heat-N-Glo 8000TVC

  • Page 1 All manuals and user guides at all-guides.com Heat-N-Glo Installers Guide Model: 8000TVC Underwriters Laboratories Listed READ THIS MANUAL BEFORE INSTALLING OR OPERATING THIS APPLIANCE. THIS WARNING INSTALLERS GUIDE MUST BE LEFT WITH IF THE INFORMATION IN THESE THE APPLIANCE FOR FUTURE REFERENCE. INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR WARNING: IMPROPER...
  • Page 2: Safety And Warning Information

    All manuals and user guides at all-guides.com SAFETY AND WARNING INFORMATION READ and UNDERSTAND all instructions carefully before starting the installation. FAILURE TO FOLLOW these installation instructions may result in a possible fire hazard and will void the warranty. Prior to the first firing of the fireplace, READ the Using Your Fireplace section of the Owners Guide.
  • Page 3 All manuals and user guides at all-guides.com Safety and Warning Information ......i Section 1: Approvals and Codes ...... 1 Table of Contents Section 2: Getting Started ........2 Section 3: Installing the Fireplace ..... 4 Section 4: Maintaining and Servicing Your Fireplace .........
  • Page 4 All manuals and user guides at all-guides.com Approval Listings Appliance Certification and Codes Installers Guide Z21.50•CGA2.2 Approvals and Codes Installation Codes High Altitude Installations...
  • Page 5: Getting Started

    All manuals and user guides at all-guides.com Introducing the Heat-N-Glo Gas Fireplaces Installers Guide Getting Started Pre-installation Preparation Installers Guide...
  • Page 6 All manuals and user guides at all-guides.com...
  • Page 7: Installing The Fireplace

    All manuals and user guides at all-guides.com Step 1 Locating the Fireplace Installing the Fireplace MODELS 8000TVC 39 1/2 Clearance Requirements...
  • Page 8 All manuals and user guides at all-guides.com Step 2 Framing the Fireplace CAUTION MEASURE FIREPLACE DIMENSIONS, AND VERIFY FRAMING METHODS AND WALL COVERING DETAILS BEFORE FRAMING CONSTRUCTION BEGINS. WARNING: To ensure proper clearances the front framing header must be installed on its narrow edge and to the front of the frame.
  • Page 9 All manuals and user guides at all-guides.com...
  • Page 10: Vent System

    All manuals and user guides at all-guides.com Step 4 A. Vent System Approvals Installing the Vent System...
  • Page 11 All manuals and user guides at all-guides.com LISTED LISTED TERMINATION CAP TERMINATION CAP LISTED SINGLE-WALL LISTED SINGLE-WALL GAS VENT GAS VENT NON-COMBUSTIBLE NON-COMBUSTIBLE CONSTRUCTION CONSTRUCTION B-TYPE B-TYPE VENT VENT MINIMUM VERTICAL RISE = 9FT MAXIMUM HORIZONTAL RUN = 15FT V:H = 2:1...
  • Page 12 All manuals and user guides at all-guides.com LOWEST DISCHARGE OPENING VENT CAP ROOF PITCH IS X/12 H (MIN.)-MINIMUM HEIGHT FROM ROOF H (MIN.)-MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE OPENING TO LOWEST DISCHARGE OPENING ROOF PITCH H (MIN.) FT. FLAT TO 6/12 6/12 TO 7/12 1.25 OVER 7/12 TO 8/12...
  • Page 13 All manuals and user guides at all-guides.com Step 5 Positioning, Leveling, and Securing the WARNING: To ensure proper Fireplace. clearances the front framing header must be installed on its narrow edge and to the front of the frame. NOTE: Non-combustible material that is supplied with unit is not shown for clarity.
  • Page 14 All manuals and user guides at all-guides.com DSI IGNITION NOTE: FLAMES TOO CLOSE TO THE CERAMIC INSULATORS CAN CAUSE NUISANCE LOCKOUTS AND ELECTRODE FAILURE. STANDING PILOT...
  • Page 15 All manuals and user guides at all-guides.com Step 7 The Gas Supply Line...
  • Page 16: Gas Pressure

    All manuals and user guides at all-guides.com Step 8 Gas Pressure Requirements...
  • Page 17 All manuals and user guides at all-guides.com Step 9 Wiring the Fireplace For Standing Pilot Ignition Wiring LABEL ALL WIRES PRIOR TO DISCONNECTION CAUTION WHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION. VERIFY PROPER OPERATION AFTER SERVICING.
  • Page 18 All manuals and user guides at all-guides.com FAN WIRING DIAGRAM NOTE: IF ANY OF THE ORIGINAL WIRE NOTE: IF ANY OF THE ORIGINAL WIRE VARIABLE SPEED CONTROL AS SUPPLIED WITH THE APPLIANCE AS SUPPLIED WITH THE APPLIANCE MUST BE REPLACED, IT MUST BE MUST BE REPLACED, IT MUST BE REPLACED WITH TYPE 105 DEGREE C REPLACED WITH TYPE 105 DEGREE C...
  • Page 19 All manuals and user guides at all-guides.com...
  • Page 20 All manuals and user guides at all-guides.com Step 10 Finishing CAUTION IF JOINTS BETWEEN THE FINISHED WALLS AND THE FIREPLACE SURROUND (TOP AND SIDES) ARE SEALED, A 300° F. MINIMUM SEALANT MATERIAL MUST BE USED. THESE JOINTS ARE NOT REQUIRED TO BE SEALED. ONLY NON-COMBUSTIBLE MATERIAL (USING 300°...
  • Page 21: Ember Material

    All manuals and user guides at all-guides.com Step 11 Installing Trim, Logs, and Ember Material ° °...
  • Page 22 All manuals and user guides at all-guides.com CAUTION IT IS STRONGLY RECOMMENDED THAT TRIM DOORS WITH OPTIONAL MESH SCREENS BE INSTALLED ON PROPANE MODELS.
  • Page 23 All manuals and user guides at all-guides.com Step 12 Before Lighting the Fireplace Installers Guide NOTE: The fireplace should be run for 8 hours on the initial start-up. This will help to cure the chemicals used in the paint and logs. Step 13 Lighting the Fireplace...
  • Page 24 All manuals and user guides at all-guides.com Fireplace Maintenance IMPORTANT TURN OFF THE GAS BEFORE SERVICING YOUR FIREPLACE. Maintaining Type of Servicing Fireplace Fireplace Maintenance Task To Maintenance Frequency Be Completed Your Fireplace Replacing Once annually, Qualified Brush away loose ember material near Old Ember during the Service...
  • Page 25 All manuals and user guides at all-guides.com MAKE SURE THE FLAMES ARE STEADY—NOT LIFTING OR FLOATING. DSI IGNITION STANDING PILOT NOTE: FLAMES TOO CLOSE TO THE CERAMIC INSULATORS CAN CAUSE NUISANCE LOCK- OUTS AND ELECTRODE FAILURE. 3/8" (10 mm)

Table of Contents