Table of Contents
Advertisement
Quick Links
Pneumatic Paint Shaker
** IMPORTANT **
BEFORE USING
THE CYCLONE SHAKER
Unscrew the lubricator bowl from the shaker
body by hand. Fill the lubricator bowl to the level
mark using air tool oil provided. There may be a
small amount of oil le� in bo�le.
Lack of lubrica�on will result in premature wear,
loss of opera�on, and possibly void the warranty.
It is critical that the Cyclone Shaker is
properly lubricated during every operation.
THANK YOU,
DEDOES INDUSTRIES
248-624-7710
www.dedoes.com
Page 1
PART # M-312 KD RV.8 2019-09-25
Advertisement
Table of Contents
Summary of Contents for Dedoes Cyclone 0910P
- Page 1 Lack of lubrica�on will result in premature wear, loss of opera�on, and possibly void the warranty. It is critical that the Cyclone Shaker is properly lubricated during every operation. THANK YOU, DEDOES INDUSTRIES 248-624-7710 www.dedoes.com Page 1 PART # M-312 KD RV.8 2019-09-25...
-
Page 2: Warranty
Dedoes will not be responsible for loss of �me, inconvenience or other consequen�al damages. Warranty is void: if there is any lack of lubrica�on and/or poor maintenance in which has caused the opera�on of the shaker to fail, if Dedoes parts are not used for repairs or installa�on, and if shaker is not installed properly. - Page 3 · Install an air filter if there’s water/dirt in the air line. · Be sure the shaker gets enough air tool oil during opera�on. For technical support on our products or addi�onal accessories, please call us at 248-624-7710 or visit our web site: www.dedoes.com Page 3...
-
Page 4: Operation
It is only to allow access to the internal Zerk fi�ng to grease. For technical support on our products or addi�onal accessories, please call us at 248-624-7710 or visit our web site: www.dedoes.com Page 4... -
Page 5: Specifications
27cm W x 21cm D x 78cm H (10.75in W x 8.25in D x 30.75in H) Weight: 7 kgs (15 lbs) For technical support on our products or addi�onal accessories, please call us at 248-624-7710 or visit our web site: www.dedoes.com Page 5... -
Page 6: Troubleshooting
1. Check the Piston O-ring (M-265) and the Check Valves (M-296 and/or M-297). Clean and replace as necessary. For technical support on our products or addi�onal accessories, please call us at 248-624-7710 or visit our web site: www.dedoes.com Page 6... - Page 7 2. The lubricator (M-318) dial is opened too much. Adjust the lubricator by turning the ver�cal line on the drip rate dial clockwise un�l it stops and then turn it counter clockwise to number 4. For technical support on our products or addi�onal accessories, please call us at 248-624-7710 or visit our web site: www.dedoes.com Page 7...
- Page 8 Use Non detergent Air Tool Oil 5W to 10W to refill the Cyclone Shaker. Grease Date Completed By Verified By Okay Added Okay Added For technical support on our products or addi�onal accessories, please call us at 248-624-7710 or visit our web site: www.dedoes.com Page 8 PART # M-312 KD RV.8 2019-09-25...
- Page 9 Complete Cyclone Shaker M-254 Clamp Nut - Right Hand M-272 Zerk Fi�ng 0915P Complete Pedestal For technical support on our products or addi�onal accessories, please call us at 248-624-7710 or visit our web site: www.dedoes.com Page 9 PART # M-312 KD RV.8-2019-09-25...
- Page 10 Assembly Body Valve Body Screw * Included within the M-232RK Rebuild Kit For technical support on our products or addi�onal accessories, please call us at 248-624-7710 or visit our web site: www.dedoes.com Page 10 PART # M-312 KD RV.8 2019-09-25...
- Page 11 PEDESTAL TO FLOOR TEMPLATE The Pedestal includes six interior holes to mount to a wheel and �re if desired. DO NOT use these holes to mount the Pedestal to the floor, damage will result. Use the outer holes in Pedestal base to mount it to the floor. The Pedestal base is 8.0 inch (203 mm) square.
- Page 12 SHAKER TO BENCH TEMPLATE IT IS HIGHLY RECOMMENDED TO MOUNT THE SHAKER TO THE OPTIONAL PEDESTAL AND SECURE THE PEDESTAL TO THE FLOOR. The shaker base is 8.0 inch (203 mm) by 10.5 inch (267 mm). Drill five 13⁄32 inch (11 mm) holes in the surface and install the shaker using 3⁄8 inch (10 mm) machine bolts.