I Hookups; Dvd/Vcr To Tv Connection; Setting The Ch3/Ch4 Switch; Connecting To A Tv - Sylvania SSD800 Owner's Manual

DVD/VCR TO TV CONNECTION

1. Disconnect the AC power cord of the TV from the
AC outlet.
2. Disconnect the antenna or cable from the TV.
3. Connect the antenna or cable to the ANT-IN jack of
the DVD/VCR COMBINATION UNITS.
4. Connect the DVD/VCR COMBINATION UNITS to
the TV using the RF cable.
5. Plug the AC power cords of the DVD/VCR COM-
BINATION UNITS and TV into the AC outlets.
[VHF/UHF
[Indoor antenna]
combination antenna]
[Cable box or satellite box]
IN
OUT
From Cable or
Satellite Company
Note to CATV system installer
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that pro-
vides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected
to the grounding system of the building, as close to the point of cable entry as practical.
Antenna/Cable signal
A/V-compatible or
wide screen TV
Notes
¡Connect the DVD/VCR COMBINATION UNITS directly to a TV. If the A/V cables are connected to a
VCR, pictures may be distorted due to the copy protection system.
S-VIDEO INPUT JACK OR COMPONENT VIDEO IN JACKS
FOR TVs WITH S-VIDEO INPUT JACK
Use an S-Video cable (commercially available) in place of the yellow video cable to enjoy higher quality pic-
tures.
The S-Video connection only supplies video (picture) in the DVD mode of the DVD/VCR COMBINATION
UNITS. Therefore, in order to use the VCR features or view TV channels on the DVD/VCR COMBINATION
UNITS, you still need to either connect the RF cable to the ANT-OUT jack of the DVD/VCR COMBINATION
UNITS and the TV's Antenna In jack, or connect the yellow video cable as described earlier (Fig.1). To connect
the supplied RF cable, see "DVD/VCR TO TV CONNECTION" above.
A/V-compatible or
wide screen TV
HOOKUPS
[Back of the DVD/VCR]
[Back of the
UHF/VHF combination TV]
RF cable
OR
ANT - IN
(supplied)
UHF/VHF
OR
ANT - OUT
CH3 CH4

CONNECTING TO A TV

ANT - IN
ANT - OUT
CH3 CH4
To ANT. IN
of TV
To VIDEO INPUT jack
To Right (red) and Left (white)
To AUDIO INPUT jacks
CONNECTING TO A TV THAT HAS AN
ANT - IN
ANT - OUT
CH3 CH4
To Right (red) and Left (white)
To AUDIO INPUT jacks
To S-VIDEO INPUT jack
SETTING THE CH3/CH4
If your TV does not have A/V terminals:
When the DVD/VCR COMBINATION UNITS is in
the VCR Playback mode or when the DVD/VCR
COMBINATION UNITS is in the VCR mode, your TV
will receive signals from the DVD/VCR COMBINA-
TION UNITS on either channel 3 or channel 4. To use
the DVD/VCR COMBINATION UNITS with your TV,
set the selector switch to CH3 or CH4 (which is locat-
ed in the back of your
DVD/VCR COMBINATION
UNITS), whichever is not
used for normal broadcasts in
your area. Then set your TV
to the same channel.
DVD/VCR
OUT
IN
L
AUDO
R
VIDEO
To VIDEO OUT jack
To AUDIO OUT jacks
DVD/VCR
IN
L
AUDO
R
VIDEO
To AUDIO OUT jacks
To S-VIDEO OUT jack
– 14 –
SWITCH
CH3 CH4
[Back of the DVD/VCR]
COMPONENT
VIDEO OUT
Y
DVD/VCR
AUDIO OUT
DIGITAL AUDIO OUT
S-VIDEO
L
Cb
PCM / BITSTREAM
OUT
COAXIAL
R Cr
COMPONENT
OUT
VIDEO OUT
Y
DVD/VCR
AUDIO OUT
DIGITAL AUDIO OUT
S-VIDEO
L
Cb
PCM / BITSTREAM
OUT
COAXIAL
R Cr
ANT - IN
ANT - OUT
CH3 CH4
[Fig. 1]
[Fig. 2]
EN
1L25