Sun Microsystems Sun Fire V440 Installation Manual
Sun Microsystems Sun Fire V440 Installation Manual

Sun Microsystems Sun Fire V440 Installation Manual

Cabling and power on

Advertisement

Sun Fire
V440 Server Setup:
Cabling and Power On
Sun Microsystems, Inc.
www.sun.com
Part No. 816-7734-12
March 2005, Revision 01
Submit comments about this document at:
http://www.sun.com/hwdocs/feedback

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Sun Fire V440 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Sun Microsystems Sun Fire V440

  • Page 1 Sun Fire V440 Server Setup: ™ Cabling and Power On Sun Microsystems, Inc. www.sun.com Part No. 816-7734-12 March 2005, Revision 01 Submit comments about this document at: http://www.sun.com/hwdocs/feedback...
  • Page 2 Copyright 2004 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, Californie 95054, Etats-Unis. Tous droits réservés. Sun Microsystems, Inc. a les droits de propriété intellectuels relatants à la technologie qui est décrit dans ce document. En particulier, et sans la limitation, ces droits de propriété...
  • Page 3: Table Of Contents

    Contents Locating the Back Panel Ports 2 Routing and Securing Cords and Cables 3 Connecting the Power Cords to the Server 4 Connecting the Ethernet Cables 6 Installing Optional Components 7 Setting Up a Console Device 7 Preparing to Configure the Primary Interface 8 Powering On the Server 9 Installing the Solaris Operating System and Other Software 11...
  • Page 4 Sun Fire V440 Server Setup: Cabling and Power On • March 2005...
  • Page 5 This guide tells you how to route the cables and cords and power on the Sun Fire V440 server. Use this guide after you have installed the Sun Fire V440 server into a rack, following instructions either on the server’s top panel or in the Sun Fire V440 Server Installation Guide.
  • Page 6: Locating The Back Panel Ports

    Locating the Back Panel Ports The following figure shows the Sun Fire V440 server back panel and identifies the AC power inlet and I/O ports. Note – Illustration does not show the cable management arm in place. Port Information AC inlets Power cords connect to each AC inlet.
  • Page 7: Routing And Securing Cords And Cables

    3. Use the Velcro straps to secure the cords and cables to the cable management arm. 4. Plug in the Ethernet cable to the RJ-45 outlet to connect to your Ethernet network. Contact your network administrator if you need more information. Sun Fire V440 Server Setup: Cabling and Power On...
  • Page 8: Connecting The Power Cords To The Server

    1. Unlock the right system door. 2. Insert the system key into the system control keyswitch. 3. Ensure that the system control keyswitch is in the Standby position. Standby position Sun Fire V440 Server Setup: Cabling and Power On • March 2005...
  • Page 9 Note – Do not connect the cords to AC power outlets at this point. You connect the cords to AC outlets during a later step, after you have set up a system console device. Sun Fire V440 Server Setup: Cabling and Power On...
  • Page 10: Connecting The Ethernet Cables

    Use the following steps to connect a twisted-pair Ethernet cable to one or both of the Ethernet ports on the back panel. See the Sun Fire V440 Server Administration Guide for more information about seeing up more than one network interface.
  • Page 11: Installing Optional Components

    Installing Optional Components If you ordered options that are not factory-installed, see the Sun Fire V440 Server Parts Installation and Removal Guide for installation instructions. Note – All internal options must be installed only by qualified service personnel. Installation and removal procedures for various parst are covered in the Sun Fire V440 Server Parts Installation and Removal Guide, which is included on the Sun Fire V440 documentation CD.
  • Page 12: Preparing To Configure The Primary Interface

    2. Connect one end of the serial cable to the terminal’s serial port. The Sun Fire V440 is a DTE machine. Use an RJ-45 serial cable or an adapter appropriate for your terminal. Plug in the cable to the terminal’s serial port connector.
  • Page 13: Powering On The Server

    Caution – The AC power cords provide a discharge path for static electricity. Unless otherwise noted in the Sun Fire V440 Parts Installation and Removal Guide, the cords must remain plugged in to the AC outlets when you handle internal components.
  • Page 14 If no network boot server is found, the ok prompt is displayed. See the Sun Fire V440 Server Installation Guide for instructions on how to perform an alternative power-on method. The Power OK LEDs on the back panel are lit when the power supply is turned on.
  • Page 15: Installing The Solaris Operating System And Other Software

    See the documentation provided in the Solaris Media Kit for a listing of included software. 4. Install any software patches listed in the Sun Fire V440 Product Notes. The latest versions of the Product Notes are located on the Sun Web site, at http://www.sun.com/documentation.
  • Page 16: For More Information

    Sun ALOM Online Help modules are are provided with the Advanced Lights Out ALOM software. You can also access the ALOM help modules Manager (ALOM) software from your Documentation CD or from the ALOM Web site: http://www.sun.com/servers/alom.html Sun Fire V440 Server Setup: Cabling and Power On • March 2005...

Table of Contents