Advertisement
TOUCH CONROL VITRO CERAMIC HOB
Record in the space below the listed information for future reference.
SERIAL NUMBER...............................................................................................
DATE OF PURCHASE..........................................................................................
PURCHASED FROM............................................................................................
.........................................................................................................................
PAGE 1 OF 12
DHD406 "600 TC"
The manufacturer strives for continuous
improvement. For this reason, the text and
illustrations in this manual are subject to change
without notice.
070232
Advertisement
Table of Contents
Related Manuals for Defy DHD406 600 TC
Summary of Contents for Defy DHD406 600 TC
- Page 1 TOUCH CONROL VITRO CERAMIC HOB DHD406 “600 TC” Record in the space below the listed information for future reference. SERIAL NUMBER………………………………………………………………………………….. DATE OF PURCHASE……………………………………………………………………………... PURCHASED FROM……………………………………………………………………………….. …………………………………………………………………………………………………………. The manufacturer strives for continuous improvement. For this reason, the text and illustrations in this manual are subject to change without notice.
- Page 2 Vitro ceramic smooth top. 10 Technical specifications. 10 Error codes. 11 Defy Service Centres. 12 Warranty. Record in the space below the listed information for future reference. The serial number may be found on the label attached to the hob base.
-
Page 3: Aperture Size
Introduction Congratulations on the purchase of this quality appliance. We trust that you will enjoy many years of trouble free use. Please read these instructions carefully before using the appliance. This book will provide you with information on how to operate and care for your appliance in order that you gain the maximum benefit from it. - Page 4 Important safety instructions This section contains safety instructions Do not use the appliance for heating that will help you avoid risk of injury and closed tins and glass jars. The damage. All warranties will become void pressure that would build up in the tin/ if you do not follow these instructions.
-
Page 5: Installation
Installation Installation is the buyer’s responsibility. The manufacturer accepts no liability for this service. Any action that the manufacturer has to take as a result of an erroneous installation will not be covered by the warranty. The hob is supplied with securing clips. These fit into dedicated slots around the hob base. -
Page 6: Electrical Installation
VERY IMPORTANT SAFETY INSTRUCTION Safety installation for hob with control panel A removable horizontal board must be fitted below the hob and 75mm away from the worktop bottom face. Space between this board and the hob must be empty and no objects may be stored or kept there. This board will effectively shield the user from the base of the hob which gets hot during use. - Page 7 Controls Ceramic glass cooktop Cooking zone Hi Light front left Cooking zone Hi Light rear left Cooking zone Hi Light rear right Cooking zone Hi Light front right Hob controls Hob control elements On/Off sensor Cooking zone power indicators (Hot surface indicators) Cooking zone selection and (+) Sensor (-) Sensor...
-
Page 8: Problem Check
Controls Switching a cooking zone off Press the (-) sensor (D) and set the power level to ‘0’, the hotplate will switch off after 10 seconds. Shortly thereafter the hot surface indicator light on the hob will switch on, dis- play (H) and remain on for 20 to 30 minutes after the plate is switched off. - Page 9 Clean the hob with a nylon pad and a suitable smooth top cleaning solution, which is available from all Defy Service Centres. Remove calcium stains (yellow stains) by applying a small amount of lime remover such as vinegar or lemon juice. Other suitable commercially available products can also be used.
-
Page 10: Technical Specifications
Overheating: The control unit switches off in CENTRE AND SPECIFY THE ERROR order to avoid damage to the unit CODE 1 CONTACT YOUR DEFY SERVICE U400 Secondary voltage of the power unit is too CENTRE AND SPECIFY THE ERROR high. Control unit switches off after one CODE second and permanent tone is emitted. -
Page 11: Defy Service Centres
Defy Service Centres If you have followed the instructions and still have a problem, contact the nearest Defy Technical Support Centre. They will be able to advise you on any aspect of the product or send a qualified technician to repair it. -
Page 12: Warranty
Point 1 of this Certificate. For warranties in the Republic of South Africa and Sub-Saharan Africa, please contact your nearest Defy office. Please refer to the previous page for respective South African service agents and Sub-Saharan Africa service agents.
Need help?
Do you have a question about the DHD406 600 TC and is the answer not in the manual?
Questions and answers
hob switches off when 2nd plate is switch on.
The Defy DHD406 600 TC hob may switch off when the second plate is turned on due to an overheating issue or a power supply problem. Specifically, error codes like ER21 (overheating) or U400 (secondary voltage too high) can cause the control unit to switch off to prevent damage.
This answer is automatically generated