Do you have a question about the 10 and is the answer not in the manual?
Questions and answers
John B Kinnemeyer
April 12, 2025
I
I have a SWR Workingman's Twelve. Someone messed with the wiring of the on / off switch, it is always on. Fix?? Thanks John
1 comments:
Mr. Anderson
April 12, 2025
To fix the wiring issue with the on/off switch on a SWR Workingman's Twelve:
1. Ensure the green/yellow wire is properly connected to ground, as it is meant for grounding only. 2. Inspect the blue wire; it should not be poorly soldered to the power connector. Correct any bad solder joints. 3. Use sealed connectors (like Abiko) instead of soldering directly to the power connector for safety and reliability. 4. Confirm the switch wiring matches the original schematic. 5. Check the transformer mounting—attach it securely with screws if it's loose or missing mounting hardware.
Always perform a safety check after repairs to confirm proper operation.
WORKINGMAN’S 10 Speaker Complement: Power Output: Impedance: Dimensions: Weight: TOP PANEL FEATURES INPUT JACK VOLUME CONTROL NOTE: AURAL ENHANCER TONE CONTROL SECTION 2 • WORKINGMAN’S COMBOS OWNER’S MANUAL...
Page 4
USING THE TONE CONTROLS BASS CONTROL MID RANGE CONTROL TREBLE CONTROL EFFECTS BLEND WORKINGMAN’S COMBOS OWNER’S MANUAL • 3...
POWER SWITCH REAR PANEL FEATURES TO TUNER EFFECTS LOOP SEND JACK RECEIVE JACK NOTE: EXTENSION SPEAKER JACK RECOMMENDED SPEAKER CABS FROM SWR ARE: 4 • WORKINGMAN’S COMBOS OWNER’S MANUAL...
Page 6
STEREO HEADPHONES JACK THREE WAY SELECTOR SWITCH Full Range Headphones Only Horn Off BALANCED DIRECT RECORD OUT NOTE: A/C LINE FUSE A/C LINE CORD RECEPTACLE NOTE: WORKINGMAN’S COMBOS OWNER’S MANUAL • 5...
WORKINGMAN’S 12 Speaker Complement: Power Output: Impedance: Dimensions: Weight: 50 FRONT PANEL FEATURES BALANCED DIRECT RECORD OUT TO TUNER INPUT JACKS Passive Input NOTE: WORKINGMAN’S COMBOS OWNER’S MANUAL • 7...
EXTENSION SPEAKER JACK Recommended speaker cabs from SWR are: STEREO HEADPHONES JACK THREE WAY SELECTOR SWITCH Full Range Headphones Only Horn Off A/C LINE FUSE A/C LINE CORD RECEPTACLE NOTE: WORKINGMAN’S COMBOS OWNER’S MANUAL • 11...
WORKINGMAN’S 15 Speaker Complement: Power Output: Impedance: Dimensions: Weight: 61 FRONT PANEL FEATURES BALANCED DIRECT RECORD OUT TO TUNER INPUT JACKS Passive Input NOTE: 14 • WORKINGMAN’S COMBOS OWNER’S MANUAL...
Page 16
Active Input NOTE: PREAMP CLIP LED NOTE: GAIN CONTROL TONE CONTROL SECTION Using the Tone Controls WORKINGMAN’S COMBOS OWNER’S MANUAL • 15...
Page 17
Bass Control Mid Range Controls NOTE: Treble Control Transparency Control AURAL ENHANCER 16 • WORKINGMAN’S COMBOS OWNER’S MANUAL...
Page 18
EFFECTS BLEND CONTROL LIMITER DEFEAT SWITCH MASTER VOLUME NOTE: LIMITER CIRCUIT LIMITER LED NOTE: THREE WAY SELECTOR SWITCH Full Range Headphones Only Horn Off WORKINGMAN’S COMBOS OWNER’S MANUAL • 17...
STEREO HEADPHONES JACK POWER SWITCH REAR PANEL FEATURES EFFECTS LOOP Send Jack Receive Jack NOTE: EXTENSION SPEAKER JACK Recommended speaker cabs from SWR are: 18 • WORKINGMAN’S COMBOS OWNER’S MANUAL...
Page 20
A/C LINE FUSE A/C LINE CORD RECEPTACLE NOTE WORKINGMAN’S COMBOS OWNER’S MANUAL • 19...
WORKINGMAN’S BASS COMBOS LIMITED WARRANTY WORKINGMAN’S BASS COMBOS from SWR are warranted to the original consumer purchas- er for ONE YEAR from the date of purchase against defects in materials and workmanship, provid- ed that it is purchased from an Authorized SWR dealer. This warranty applies only to products purchased in the USA or Canada.
Need help?
Do you have a question about the 10 and is the answer not in the manual?
Questions and answers
I I have a SWR Workingman's Twelve. Someone messed with the wiring of the on / off switch, it is always on. Fix?? Thanks John
To fix the wiring issue with the on/off switch on a SWR Workingman's Twelve:
1. Ensure the green/yellow wire is properly connected to ground, as it is meant for grounding only.
2. Inspect the blue wire; it should not be poorly soldered to the power connector. Correct any bad solder joints.
3. Use sealed connectors (like Abiko) instead of soldering directly to the power connector for safety and reliability.
4. Confirm the switch wiring matches the original schematic.
5. Check the transformer mounting—attach it securely with screws if it's loose or missing mounting hardware.
Always perform a safety check after repairs to confirm proper operation.
This answer is automatically generated