Eaton NRX Series Installation Instructions Manual

Eaton NRX Series Installation Instructions Manual

Ethernet communications adapter module.
Hide thumbs Also See for NRX Series:

Advertisement

Available languages

Available languages

Instruction Leaflet
Installation Instructions for Series NRX
Ethernet Communications Adapter
Module
Instructions apply to:
Series NRX, Type NF Frame
ANSI, UL1066, UL489 / IEC, IZMX16, IZM91
1600 NRX SUB-TITLE IMAGE (12/15/2010)
(1) ONLY QUALIFIED ELECTRICAL PERSONNEL SHOULD BE PERMITTED TO WORK
ON THE EQUIPMENT.
(2) ALWAYS DE-ENERGIZE PRIMARY AND SECONDARY CIRCUITS IF A CIRCUIT
BREAKER CANNOT BE REMOVED TO A SAFE WORK LOCATION.
(3) DRAWOUT CIRCUIT BREAKERS SHOULD BE LEVERED (RACKED) OUT TO THE
DISCONNECT POSITION.
(4) ALL CIRCUIT BREAKERS SHOULD BE SWITCHED TO THE OFF POSITION AND
MECHANISM SPRINGS DISCHARGED.
FAILURE TO FOLLOW THESE STEPS FOR ALL PROCEDURES DESCRIBED IN THIS
INSTRUCTION LEAFLET COULD RESULT IN DEATH, BODILY INJURY, OR PROPERTY
DAMAGE.
THE INSTRUCTIONS CONTAINED IN THIS IL AND ON PRODUCT LABELS HAVE TO
BE FOLLOWED. OBSERVE THE FIVE SAFETY RULES:
– DISCONNECTING
– ENSURE THAT DEVICES CANNOT BE ACCIDENTALLY RESTARTED
– VERIFY ISOLATION FROM THE SUPPLY
– EARTHING AND SHORT-CIRCUITING
– COVERING OR PROVIDING BARRIERS TO ADJACENT LIVE PARTS
DISCONNECT THE EQUIPMENT FROM THE SUPPLY. USE ONLY AUTHORIZED
SPARE PARTS IN THE REPAIR OF THE EQUIPMENT. THE SPECIFIED MAINTENANCE
INTERVALS AS WELL AS THE INSTRUCTIONS FOR REPAIR AND EXCHANGE MUST
BE STRICTLY ADHERED TO PREVENT INJURY TO PERSONNEL AND DAMAGE TO
THE SWITCHBOARD.
IL01301052E
• WARNING
• WARNING
effective May 2012
Series NRX, Type RF Frame
IEC, IZMX40
4000 NRX RF DRAWOUT SUBTITLE IMAGE (12/15/2010)
Series NRX

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NRX Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Eaton NRX Series

  • Page 1 Instruction Leaflet IL01301052E effective May 2012 Series NRX Installation Instructions for Series NRX Ethernet Communications Adapter Module Instructions apply to: Series NRX, Type NF Frame Series NRX, Type RF Frame IEC, IZMX40 ANSI, UL1066, UL489 / IEC, IZMX16, IZM91 4000 NRX RF DRAWOUT SUBTITLE IMAGE (12/15/2010) 1600 NRX SUB-TITLE IMAGE (12/15/2010) •...
  • Page 2: Section 1: General Information

    The following tools should be available: as open/close breaker. Additionally, the Series NRX ECAM provides • #T-15 Torx data communications to the Eaton Power Xpert Software as an easy means of centralizing and gathering data for long-term data archival, • Small flat blade screwdriver analysis, and trending.
  • Page 3 Step 4 Step 5e: Tilt the communications module backward to engage the lower part of the DIN rail, and then snap it back into the DIN rail for complete engagement. Figure 8. Step 7 Figure 6. Step 5 EATON CORPORATION www.eaton.com...
  • Page 4: Section 3: Basic Wiring Rules

    Please refer to the IMPACC™ wiring specification TD17513 for detailed locations on the Ethernet Communications Adapter Module. wiring instructions. otee: For technical documents please go to www.eaton.com and search for “TD17513” . Status LED Section 4: Ethernet Communications Adapter Module Connections •...
  • Page 5 When the Communications Module is employed and Source Ground or Zero Sequence Ground Sensing method is required, the Ground Fault function is enabled by this jumper. o Use shielded Ethernet cable. Figure 10. Series NRX Ethernet Communication with Digitrip 520M EATON CORPORATION www.eaton.com...
  • Page 6 Choose Shunt Trip voltage rating to be the same as Spring Release voltage rating if communication is required. m Control Power voltage rating must match ST and SR coil voltage rating. n Close duration is two seconds on communication activation when comm control is enabled. Figure 11. Communications Control (SR and ST Wiring) EATON CORPORATION www.eaton.com...
  • Page 7: Section 6: Viewing/Setting Ethernet Address

    ECAM configuration information. Three special numeric values may be entered to clear the Control Password, reset the admin password, or reset the ECAM configuration information: • 9 Reset control password • 15 Reset admin password • 31 Reset ECAM configuration information EATON CORPORATION www.eaton.com...
  • Page 8: Section 7: Troubleshooting

    NRX Ethernet Communications Adapter Module are addressed below. 0 = no 1 = yes If you have additional questions or need further information and/or instructions, please contact your local Eaton sales representative. Observation 1—Status LED not flashing Action—Verify proper input power to module connectors.
  • Page 9 Instruction Leaflet IL01301052E Ethernet Communications Adapter effective May 2012 Module Select “ECAM Configuration” then “Date/Time” to configure the ECAM clock. Screen Shot 2. Click the Locale tab and select the proper time zone from the drop-down list. EATON CORPORATION www.eaton.com...
  • Page 10 NTP – select NTP , enter up to 3 NTP server IP addresses, and click <Use NTP> Manual – select Manual and click <Use Manual> to execute a manual time update using the PC clock Trip Unit – select and click <Use Trip Unit> to permit the Trip Unit to set ECAM time. EATON CORPORATION www.eaton.com...
  • Page 11 Installation Instructions for Series NRX Instruction Leaflet IL01301052E Ethernet Communications Adapter effective May 2012 Module Screen Shot 4. Verify the proper time. EATON CORPORATION www.eaton.com...
  • Page 12 Instruction Leaflet IL01301052E Installation Instructions for Series NRX Ethernet Communications Adapter effective May 2012 Module Screen Shot 5. Data View -> Summarye: Default web page to View Trip Unit info, status, and currents EATON CORPORATION www.eaton.com...
  • Page 13 Installation Instructions for Series NRX Instruction Leaflet IL01301052E Ethernet Communications Adapter effective May 2012 Module Click the Controls hyperlink: Open/Close breaker if enabled, Enable/Disable Maintenance Mode, Reset Trip Screen Shot 6. Trip Unit Control EATON CORPORATION www.eaton.com...
  • Page 14 Instruction Leaflet IL01301052E Installation Instructions for Series NRX Ethernet Communications Adapter effective May 2012 Module Data View Setpoints NRX 520M Trip Unit provides only View Setpoints Screen Shot 7. Data View - Setpoints EATON CORPORATION www.eaton.com...
  • Page 15 Installation Instructions for Series NRX Instruction Leaflet IL01301052E Ethernet Communications Adapter effective May 2012 Module Alarm Status View active alarms; Acknowledge/Close active alarms; Save alarms to a file. Screen Shot 8. Alarm Status EATON CORPORATION www.eaton.com...
  • Page 16 Select the value to graph from the right hand drop down box for Plot Selection. Double click the value or select the value and click the <Add> button to graph the parameter. Separate y axis scaling values are provided for each value graphed. Screen Shot 9. Trend Graphs EATON CORPORATION www.eaton.com...
  • Page 17 Enter the number of rows to display on the page in the table Height box. Click <Apply> to view the logged data. The Data Log can be saved to a file or erased using the buttons provided. Screen Shot 10. Data Logs EATON CORPORATION www.eaton.com...
  • Page 18 Instruction Leaflet IL01301052E Installation Instructions for Series NRX Ethernet Communications Adapter effective May 2012 Module Event Log Either View or Erase the Event Log using the buttons provided. <View the log> opens a csv file. Screen Shot 11. Event EATON CORPORATION www.eaton.com...
  • Page 19 Installation Instructions for Series NRX Instruction Leaflet IL01301052E Ethernet Communications Adapter effective May 2012 Module Command Log Displays active, terminated, and denied commands executed. Screen Shot 12. Commands EATON CORPORATION www.eaton.com...
  • Page 20 An optional control password can be configured to provide additional security for control functions. This password only needs to be entered once and remains in effect until the web browser session is closed. The first tab (Web Server) on the Access Control/web page allows the user to change the Ethernet port. Screen Shot 13. Access Control EATON CORPORATION www.eaton.com...
  • Page 21 Installation Instructions for Series NRX Instruction Leaflet IL01301052E Ethernet Communications Adapter effective May 2012 Module The second tab (security) on the Access Control/web page is where the optional control password is set and changed. Screen Shot 14. Access Control (continued) EATON CORPORATION www.eaton.com...
  • Page 22 Installation Instructions for Series NRX Ethernet Communications Adapter effective May 2012 Module The third tab (users) on the Access Control/web page is where the user and administrative user names and passwords are managed. Screen Shot 15. Access Control (continued) EATON CORPORATION www.eaton.com...
  • Page 23 The ECAM configuration for alarms, logging, and email can be saved to and retrieved from a file. Click <Create Configuration Archive> on the “Configuration Files” tab to create the archive, then click the link provided to save the archive file to your PC. Screen Shot 16. Import/Export EATON CORPORATION www.eaton.com...
  • Page 24 Installation Instructions for Series NRX Ethernet Communications Adapter effective May 2012 Module Click <Choose File> on the “Save Configuration to ECAM” tab to retrieve the archive file from your PC and save it to ECAM. Screen Shot 17. Import/Export (continued) EATON CORPORATION www.eaton.com...
  • Page 25 Module Network Change Network addresses (i e Static IP , Subnet Mask, Default Gateway) and Enable / Disable DHCP . ECAM is shipped with DHCP disabled and a default IP address of 10.0.0.2. Screen Shot 18. Network EATON CORPORATION www.eaton.com...
  • Page 26 Instruction Leaflet IL01301052E Installation Instructions for Series NRX Ethernet Communications Adapter effective May 2012 Module Email The Ethernet CAM module will send email notifications of events when properly configured. Screen Shot 19. Trip Unit Email Configuration EATON CORPORATION www.eaton.com...
  • Page 27 Installation Instructions for Series NRX Instruction Leaflet IL01301052E Ethernet Communications Adapter effective May 2012 Module Step 1e: Enter the SMTP server settings and click the <Submit Changes> button. Screen Shot 20. Trip Unit Email Configuration (continued) EATON CORPORATION www.eaton.com...
  • Page 28 Step 2e: Enter the Recipient name and email addresses, and select the type of events to trigger email notifications. Click the < Submit > button. A test email can be sent from this web page to verify proper recipient and mail server configuration. Screen Shot 21. Trip Unit Email Configuration (continued) EATON CORPORATION www.eaton.com...
  • Page 29 Instruction Leaflet IL01301052E Ethernet Communications Adapter effective May 2012 Module Step 3e: Select the events to trigger email notification on the Templates tab of the Email web page and click <Submit>. Screen Shot 22. Trip Unit Email Configuration (continued) EATON CORPORATION www.eaton.com...
  • Page 30 5. Click <Yes> to reboot ECAM and wait approximately 2 minutes for ECAM to reboot. otee: The Firmware page also has a button that will clear all configuration data from ECAM memory. Once the command has been initiated, all configurations will be lost Screen Shot 23. Firmware Configuration Settings EATON CORPORATION www.eaton.com...
  • Page 31 Installation Instructions for Series NRX Instruction Leaflet IL01301052E Ethernet Communications Adapter effective May 2012 Module Alarm Configuration Enable Alarms and set upper and lower limits for analog alarm values Screen Shot 24. Alarm Configuration EATON CORPORATION www.eaton.com...
  • Page 32 Instruction Leaflet IL01301052E Installation Instructions for Series NRX Ethernet Communications Adapter effective May 2012 Module Log Configuration Screen Shot 25. Log Configuration EATON CORPORATION www.eaton.com...
  • Page 33 The NRX 520M trip unit settings are configured using dials on the front of the trip unit. This page currently just displays the setpoints currently programmed into the trip unit. Remote setting capability will be available in the future for the NRX 1150 trip unit. Screen Shot 26. Setpoint Configuration EATON CORPORATION www.eaton.com...
  • Page 34: Disclaimer Of Warranties And Limitation Of Liability

    Disclaimer of warranties and limitation of liability The information, recommendations, descriptions, and safety notations In no event will Eaton be responsible to the purchaser or user in in this document are based on Eaton Corporation’s (“Eaton”) contract, in tort (including negligence), strict liability, or otherwise experience and judgment, and may not cover all contingencies.
  • Page 35 Instruction Leaflet IL01301052E gültig ab Mai 2012 Series NRX Montageanweisung für Series NRX Ethernet Kommuniactionsmodul Die Montageanweisung ist für folgende Baugrößen gültig: Series NRX, Type NF Frame Series NRX, Type RF Frame IEC, IZMX40 ANSI, UL1066, UL489 / IEC, IZMX16, IZM91 4000 NRX RF DRAWOUT SUBTITLE IMAGE (12/15/2010) 1600 NRX SUB-TITLE IMAGE (12/15/2010) •...
  • Page 36: Abschnitt 1: Allgemeine Informationen

    Die folgenden Schrtte beschreiben die Installtion des ECAM in einen steuern (z. Bsp. Ein- und Ausschalten des Leistungsschalters). Series NRX Leistungsschalter in Ausfahrtechnik. Das ECAM kann mit der Eaton Power Xpert Software kommunizieren. Diese dient zum Sammeln von Daten für die Langzeitarchivierung, nmerkungg: In dieser Montageanweisung wird an einigen Stellen nur die Baugröße NRX-NF für Illustrationszwecke gezeigt.
  • Page 37 Der ANschluss der Leitungen wird in Abschnitt 3 beschrieben. Befestigungsschraube Abbildung 5. Schritt 4 Schritt 5g: Setzen Sie das Kommunikationsmodul unten an die Steuerleitungsleiste an und lassen Sie es oben an der Leiste einschnappen. Abbildung 8. Schritt 7 EATON CORPORATION www.eaton.com...
  • Page 38 Für die Verbindung zum ECAM wird ein geschirmtes Ethernetkabel benötigt. Siehe IMPACC™ Verdrahtungsrichtlinien TD17513 für detaillierte Anweisungen. Anmerkungg: Rufen Sie www.eaton.com auf und suchen Sie nach “TD17513” . Status LED Abschnitt 4: Verbinden des ECAM • WARNUNG BEACHTEN SIE BEI WARTUNGS- UND MONTAGEARBEITEN ALLE EMPFEHLUNGEN, HINWEISE UND WARNUNGEN BEZÜGLICH DER...
  • Page 39  Wenn ein Kommunikationsmodul verwendet wird und der Erdschluss soll mit Fehlerstromquellenmessung oder Nullmessung gemessen werden, dann wird die Erdschlussfunktion mit der Brücke am Kommunikationsmodul aktiviert.  Verwenden Sie ein geschirmtes Ethernetkabel. Abbildung 10. Series NRX Ethernetkommunikation mit Auslöseelektronik Digitrip 520M EATON CORPORATION www.eaton.com...
  • Page 40  Die Bemessungsspanung des Arbeitsstromauslösers muss der des Einschaltauslöser entsprechen, wenn Kommunikationsfunktionalität benötigt wird..  Bemessungssteuerspannung muss der Spulenspannung des Arbeitsstromauslösers und des Einschaltauslöser entsprechen.  Schließzeit bei Aktivierung der Kommunikation beträgt 2 Sekunden. Abbildung 11. Kommunicationskontrolle (Verdrahtung Arbeitsstromauslöser und Einschalt auslöser EATON CORPORATION www.eaton.com...
  • Page 41 ECAM Konfigurationsinformationen zu löschen. Drei spezielle, numerische Werte können eingegeben werden, um das Kontrollpasswort zu löschen, das Administrator Passwort zurückzusetzen oder die ECAM Konfigurationsinformationen zurückzusetzen: • 9 Kontrollpasswort löschen • 15 Administratorpasswort löschen • 31 ECAM Konfigurationsinformationen löschen EATON CORPORATION www.eaton.com...
  • Page 42: Abschnitt 7: Problemlösungen

    Kommando- und Erreignislogs benötigt. SP08 Reset PIN Die beste Option für eine zuverlässige zeitnahme ist, mit einem NTP- server für die zeitsynchronisation. Wählen Sie ECAM Konfiguration - Datum/Zeit um die ECAM-Uhr zu Abbildung 12. Verlaufsdiagram Einstellungssequenz konfigurieren. EATON CORPORATION www.eaton.com...
  • Page 43 Montageanweisung für Series NRX Instruction Leaflet IL01301052E Ethernet Kommuniactionsmodul gültig ab Mai 2012 Screenshot 2. Datum- und Zeiteinstellungen konfigurieren EATON CORPORATION www.eaton.com...
  • Page 44 2. Manuell – wählen Sie Manuell und klicken Sie auf < Manuell verwenden> um eine manuelle Zeitaktualisierung durch der PC-Uhr anzuwenden 3. Auslöser – wählen und klicken Sie auf <Auslöser verwenden> um den Auslöser zu erlauben die ECAM-Zeit zu setzen EATON CORPORATION www.eaton.com...
  • Page 45 Montageanweisung für Series NRX Instruction Leaflet IL01301052E Ethernet Kommuniactionsmodul gültig ab Mai 2012 Screenshot 4. Prüfen Sie ihre Einstellungen. EATON CORPORATION www.eaton.com...
  • Page 46 Instruction Leaflet IL01301052E Montageanweisung für Series NRX Ethernet Kommuniactionsmodul gültig ab Mai 2012 Screenshot 5. Datenansicht -> Zusammenfassungg: Standardseite für Informationen bezüglich Auslöselektronik, Status und Strömen EATON CORPORATION www.eaton.com...
  • Page 47 Montageanweisung für Series NRX Instruction Leaflet IL01301052E Ethernet Kommuniactionsmodul gültig ab Mai 2012 Klicken des Controls-Hyperlinks: Ein/Ausschalten des Leistungsschalters, wenn freigeschaltet; Ein/Ausschalten des Wartungsmodus, Resetauslösung Screenshot 6. Kontrollfunktionen für Auslöseelektronik EATON CORPORATION www.eaton.com...
  • Page 48 Instruction Leaflet IL01301052E Montageanweisung für Series NRX Ethernet Kommuniactionsmodul gültig ab Mai 2012 Datenansicht Setpoints NRX 520M Auslöselektronik stellt nur Ansichts-Setpoints zur Verfügung Screenshot 7. Datenansicht - Setpoints EATON CORPORATION www.eaton.com...
  • Page 49 Montageanweisung für Series NRX Instruction Leaflet IL01301052E Ethernet Kommuniactionsmodul gültig ab Mai 2012 Alarm Status Übersicht der aktiven Alarme; Bestätigen/Abschalten von aktiven Alarmen; Alarme in einer Datei abspeichern. Screenshot 8. Alarm Status EATON CORPORATION www.eaton.com...
  • Page 50 Wählen Sie den abzubildenden Wert von der rechten Dropdownbox für Plot Selection. Doppelkiclken Sie auf den Wert oder wählen Sie den Wert und klicken Sie auf die Add-Schaltfläche um den Parameter abzubilden. Unterschiedliche y-Achsen Skalierungswerte sind für jeden abgebildeten Wert verfügbar. Screenshot 9. Trend Graphen EATON CORPORATION www.eaton.com...
  • Page 51 Geben Sie die Anzahl der darzustellenden Zeilen in die Table-Height Box ein. Klicken Sie auf <Apply> um die gespeicherten Log-Daten anzuzeigen. Das Daten-Log kann über die entsprechenden Schaltflächen in einer Datei gespeichert oder gelöscht werden. Screenshot 10. Daten-Logs EATON CORPORATION www.eaton.com...
  • Page 52 Instruction Leaflet IL01301052E Montageanweisung für Series NRX Ethernet Kommuniactionsmodul gültig ab Mai 2012 Ereignis-Log Schauen Sie sich das Ereignis-Log an oder löschen Sie es über die entsprechenden Schaltflächen. <View the log> öffnet eine csv Datei. Screenshot 11. Ereignis-Log EATON CORPORATION www.eaton.com...
  • Page 53 Montageanweisung für Series NRX Instruction Leaflet IL01301052E Ethernet Kommuniactionsmodul gültig ab Mai 2012 Befehls-Log Zeigt aktive, beendete und verweigerte Befehle an, die gegeben wurden. Screenshot 12. Befehls-Log EATON CORPORATION www.eaton.com...
  • Page 54 Ein optionales Kontrollpasswort kann aus Sicherheitsgründen vergeben werden, um die Kontrollfunktionen zu schützen. Das Passwort muss nur einmal eingegeben werden, die Sicherheitsfreigabe bleibt für die Dauer der Browsersitzung bestehen. Das erste Tab (Web Server) auf der Access Control/web page erlaubt dem Benutzer die Änderung des Ethernetports. Screenshot 13. Zungangskontrolle EATON CORPORATION www.eaton.com...
  • Page 55 Montageanweisung für Series NRX Instruction Leaflet IL01301052E Ethernet Kommuniactionsmodul gültig ab Mai 2012 Auf dem zweiten Tab (Security) der Access Control/web page kann das optionale Kontrollpasswort vergeben und geändert werden. Screenshot 14. Zugangskontrolle EATON CORPORATION www.eaton.com...
  • Page 56 Instruction Leaflet IL01301052E Montageanweisung für Series NRX Ethernet Kommuniactionsmodul gültig ab Mai 2012 Auf dem dritten Tab (users) der Access Control/web page werden die Namen und Passwörter der Benutzer und Administratoren verwaltet. Screenshot 15. Zugangskontrolle EATON CORPORATION www.eaton.com...
  • Page 57 Die Konfiguration des ECAM für Alarme, Logs und Email kann in einer Datei gespeichert und von dieser wieder geladen werden. Klicken Sie auf <Create Configuration Archive> im “Configuration Files” Tab, um das Archiv zu erzeugen. Klicken Sie anschließend auf den erscheinenden Link, um die Archivdatei auf ihren PC zu speichern. Screenshot 16. Import/Export EATON CORPORATION www.eaton.com...
  • Page 58 Montageanweisung für Series NRX Ethernet Kommuniactionsmodul gültig ab Mai 2012 Klicken Sie auf <Choose File> im “Save Configuration to ECAM” Tab, um eine Archivdatei von Ihrem PC zu laden und auf dem ECAM zu speichern. Screenshot 17. Import/Export EATON CORPORATION www.eaton.com...
  • Page 59 Ethernet Kommuniactionsmodul gültig ab Mai 2012 Netzwerk Ändern Sie die Netzwerkadresse (Static IP , Subnet Mask, Default Gateway) und schalten Sie DHCP ein/aus. ECAM wird mit ausgeschaltetem DHCP und der Standard-IP Adresse 10.0.0.2. geliefert. Screenshot 18. Netzwerk EATON CORPORATION www.eaton.com...
  • Page 60 Instruction Leaflet IL01301052E Montageanweisung für Series NRX Ethernet Kommuniactionsmodul gültig ab Mai 2012 Email Das ECAM kann, wenn entsprechend konfiguriert, Benachrichtigungen per Email verschicken. Screenshot 19. Konfiguration Emailüberwachung der Auslöselektronik EATON CORPORATION www.eaton.com...
  • Page 61 Montageanweisung für Series NRX Instruction Leaflet IL01301052E Ethernet Kommuniactionsmodul gültig ab Mai 2012 Schritt 1g: Geben Sie die Einstellungsdaten des SMTP Servers ein und klicken Sie auf die Schaltfläche <Submit Changes>. Screenshot 20. Konfiguration Emailüberwachung der Auslöselektronik EATON CORPORATION www.eaton.com...
  • Page 62 Schritt 2g: Geben Sie den Namen und die Emailadresse des Empfängers ein und legen Sie fest, in welchen Fällen der Empfänger über Ereignisse per Email benachrichtigt werden soll. Klicken Sie auf die Schaltfläche < Submit >. Eine Test-EMail kann von dieser Seite verschickt werden , um die Einstellungen zu überprüfen. Screenshot 21. Konfiguration Emailüberwachung der Auslöselektronik EATON CORPORATION www.eaton.com...
  • Page 63 Mai 2012 Schritt 3g: Wählen Sie die Art der Ereignisse über welche der Empfänger per Email benachrichtig werden soll im Templates Tab und klicken Sie auf die Schaltfläche <Submit>. Screenshot 22. Konfiguration Emailüberwachung der Auslöselektronik EATON CORPORATION www.eaton.com...
  • Page 64 5. Klicken SIe auf <Yes> um das ECAM neu zu starten. Dieser Vorgang kann bis zu zwei Minten dauern. nmerkungg: Die Firmwareseite bietet auch die Möglichkeit über die entsprechende Schaltfläche alle Konfigurationsdaten vom ECAM-Speicher zu löschen. Sobald der Befehl gegeben wurde, werden alle Daten gelöscht. Screenshot 23. Firmware-Konfigurationseinstellungen EATON CORPORATION www.eaton.com...
  • Page 65 Montageanweisung für Series NRX Instruction Leaflet IL01301052E Ethernet Kommuniactionsmodul gültig ab Mai 2012 Alarmkonfiguration Schalten Sie die Alarme ein und stellen Sie die oberen und unteren Grenzen für die analogen Alarmwerte ein. Screenshot 24. Alarmkonfiguration EATON CORPORATION www.eaton.com...
  • Page 66 Instruction Leaflet IL01301052E Montageanweisung für Series NRX Ethernet Kommuniactionsmodul gültig ab Mai 2012 Logkonfiguration Screenshot 25. Logkonfiguration EATON CORPORATION www.eaton.com...
  • Page 67 Die Einstellungen der NRX 520M Auslöselektronik werden über Drehkodierschalter auf der Vorderseite der Auslöseelektronik konfiguriert. Diese Seite zeigt lediglich die momentan einprogrammierten EInstellungen der Auslöseelektronik an. Ein Fernzugriff auf die Einstellungen ist nur bei einer Auslöselektronik vom Typ 1150 möglich. Screenshot 26. Setpoint-Konfiguration EATON CORPORATION www.eaton.com...
  • Page 68 1000 Cherrington Parkway Moon Township, PA 15108 United States 877-ETN-CARE (877-386-2273) Eaton.com Power Chain Management is a registered © 2012 Eaton Corporation Trademark of Eaton Corporation All Rights Reserved Printed in USA All other Trademarks are property of their Publication No. IL01301052EH05 respective owners.

This manual is also suitable for:

Nrx 520mNrx 1150

Table of Contents