Supermicro AS1011M-T2 single processor AS1011M-T2 User Manual
  1. Manuals
  2. Brands
  3. Supermicro Manuals
  4. Server
  5. AS-1011M-T2
  6. User manual
Supermicro AS1011M-T2 single processor AS1011M-T2 User Manual

Supermicro AS1011M-T2 single processor AS1011M-T2 User Manual

Super micro computeruser's manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
AS1011M-T2
USER'S MANUAL
1.0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AS1011M-T2 single processor AS1011M-T2 and is the answer not in the manual?

Questions and answers

Related Manuals for Supermicro AS1011M-T2 single processor AS1011M-T2

Summary of Contents for Supermicro AS1011M-T2 single processor AS1011M-T2

  • Page 1 AS1011M-T2 USER’S MANUAL...
  • Page 2 The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates.

  • Page 3: About This Manual

    Preface Preface About This Manual This manual is written for professional system integrators and PC technicians. It provides information for the installation and use of the AS1011M-T2 server. Instal- lation and maintenance should be performed by experienced technicians only. The AS1011M-T2 is a high-end server based on the SC811FT-260 1U rack- mount chassis and the H8SMi-2, a single processor motherboard that supports AMD Opteron processors and up to 8 GB of unbuffered ECC/non-ECC DDR2- 800/667/533 SDRAM.
  • Page 4 AS1011M-T2 User's Manual Chapter 4: System Safety You should thoroughly familiarize yourself with this chapter for a general overview of safety precautions that should be followed when installing and servicing the 1011M-T2. Chapter 5: Advanced Motherboard Setup Chapter 5 provides detailed information on the H8SMi-2 motherboard, including the locations and functions of connections, headers and jumpers.
  • Page 5 Preface Notes...

  • Page 6: Table Of Contents

    AS1011M-T2 User's Manual Table of Contents Preface About This Manual ... iii Manual Organization ... iii Chapter 1: Introduction Overview ... 1-1 Motherboard Features ... 1-2 Server Chassis Features ... 1-4 Contacting Supermicro ... 1-5 Chapter 2: Server Installation Overview ... 2-1 Unpacking the System ...
  • Page 7 Chapter 5: Advanced Motherboard Setup Handling the Motherboard ... 5-1 Mounting the Motherboard into a Chassis ... 5-2 Processor and Heatsink Installation ... 5-2 Connecting Cables ... 5-5 Connecting Data Cables ... 5-5 Connecting Power Cables ... 5-5 Connecting the Control Panel ... 5-6 I/O Ports ...
  • Page 8 AS1011M-T2 User's Manual Power Supply Fail Alarm Reset Header ... 5-18 Compact Flash Power ... 5-18 SGPIO ... 5-18 5-10 Jumper Settings ... 5-19 Explanation of Jumpers ... 5-19 CMOS Clear ... 5-19 VGA Enable/Disable ... 5-20 C to PCI Enable/Disable ... 5-20 Watch Dog Enable/Disable ...
  • Page 9 Chapter 7: BIOS Introduction ... 7-1 Main Menu ... 7-2 Advanced Settings Menu ... 7-2 Boot Menu ... 7-17 Security Menu ... 7-18 Exit Menu ... 7-18 Appendices: Appendix A: BIOS Error Beep Codes ...A-1 Appendix B: BIOS POST Checkpoint Codes ...B-1 Appendix C: System Specifi...
  • Page 10 AS1011M-T2 User's Manual Notes...

  • Page 11: Chapter 1: Introduction

    Overview The AS1011M-T2 is a high-end single processor, mini 1U rackmount server com- prised of two main subsystems: the SC811FT-260 chassis and the H8SMi-2 moth- erboard. The H8SMi-2 supports a single AMD Opteron 1000 series processor in a 940-pin AM2 socket and up to 8 GB of ECC/non-ECC DDR2-800/667/533 SDRAM memory.

  • Page 12: Motherboard Features

    AS1011M-T2 User's Manual Motherboard Features At the heart of the 1011M-T2 lies the H8SMi-2, a single processor motherboard designed to provide maximum performance. Below are the main features of the H8SMi-2. (See Figure 1-1 for a block diagram of the chipset.) Processors The H8SMi-2 has an 940-pin AM2 type socket that supports a single AMD Opteron Series 1000 processor.

  • Page 13: Other Features

    Onboard Controllers/Ports An onboard IDE controller supports one fl oppy drive and one Ultra ATA 133 hard drive or ATAPI device. Onboard I/O backpanel ports include one serial COM port, two USB ports, a VGA (monitor) port, PS/2 mouse and keyboard ports, a parallel port and two GLAN (RJ45) ports.

  • Page 14: Server Chassis Features

    AS1011M-T2 User's Manual Server Chassis Features The 1011M-T2 is a mini 1U rackmount server platform confi guration. The following is a general outline of the main features of the SC811FT-260 chassis. System Power When confi gured as a 1011M-T2, the SC811FT-260 chassis includes a single 260W power supply.

  • Page 15: Contacting Supermicro

    Contacting Supermicro Headquarters Address: SuperMicro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (Technical Support) Web Site: www.supermicro.com Europe Address: SuperMicro Computer B.V. Het Sterrenbeeld 28, 5215 ML 's-Hertogenbosch, The Netherlands Tel: +31 (0) 73-6400390...
  • Page 16 AS1011M-T2 User's Manual Notes...

  • Page 17: Chapter 2: Server Installation

    Server Installation 2-1 Overview This chapter provides a quick setup checklist to get your 1011M-T2 up and run- ning. Following the steps in the order given should enable you to have the system operational within a minimal amount of time. This quick setup assumes that your 1011M-T2 system has come to you with the processor and memory preinstalled.

  • Page 18: Warnings And Precautions

    AS1011M-T2 User's Manual Choosing a Setup Location - Leave enough clearance in front of the rack to enable you to open the front door completely (~25 inches). - Leave approximately 30 inches of clearance in the back of the rack to allow for suffi...

  • Page 19: Rack Mounting Considerations

    Chapter 2: Server Installation Rack Mounting Considerations Ambient Operating Temperature If installed in a closed or multi-unit rack assembly, the ambient operating tempera- ture of the rack environment may be greater than the ambient temperature of the room. Therefore, consideration should be given to installing the equipment in an environment compatible with the manufacturer’s maximum rated ambient tempera- ture (Tmra).

  • Page 20: Installing The System Into A Rack

    AS1011M-T2 User's Manual Installing the System into a Rack This section provides information on installing the 1011M-T2 into a rack unit. If the system has already been mounted into a rack, you can skip ahead to Sections 2-5 and 2-6. There are a variety of rack units on the market, which may mean the assembly procedure will differ slightly.

  • Page 21: Installing The Chassis Rails

    Chapter 2: Server Installation Installing the Chassis Rails Position the fixed chassis rail sections you just removed along the side of the chassis making sure the fi ve screw holes line up. Note that these two rails are left/right specifi c. Screw the rail securely to the side of the chassis (see Figure 2-2).

  • Page 22: Installing The Server Into The Rack

    AS1011M-T2 User's Manual Installing the Server into the Rack You should now have rails attached to both the chassis and the rack unit. The next step is to install the server into the rack. Do this by lining up the rear of the chas- sis rails with the front of the rack rails.

  • Page 23: Installing The Server Into A Telco Rack

    Chapter 2: Server Installation Installing the Server into a Telco Rack If you are installing the 1011M-T2 into a Telco type rack, follow the directions given on the previous pages for rack installation. The only difference in the installation procedure will be the positioning of the rack brackets to the rack. They should be spaced apart just enough to accomodate the width of the telco rack.

  • Page 24: Checking The Motherboard Setup

    AS1011M-T2 User's Manual Checking the Motherboard Setup After you install the 1011M-T2 in the rack, you will need to open the unit to make sure the motherboard is properly installed and all the connections have been made. 1. Accessing the inside of the system (Figure 2-5) First, grasp the two handles on either side and pull the unit straight out until it locks (you will hear a "click").
  • Page 25 Chapter 2: Server Installation Figure 2-5. Accessing the Inside of the System...

  • Page 26: Checking The Drive Bay Setup

    AS1011M-T2 User's Manual Checking the Drive Bay Setup Next, you should check to make sure the peripheral drives and the Serial ATA drives and Serial ATA backplane have been properly installed and all essential connec- tions have been made. 1. Accessing the drive bays All drives can be accessed from the front of the server.

  • Page 27: Chapter 3: System Interface

    System Interface Overview There are several LEDs on the control panel as well as others on the Serial ATA drive carriers to keep you constantly informed of the overall status of the system as well as the activity and health of specifi c components. There are also two but- tons on the chassis control panel.

  • Page 28: Control Panel Leds

    AS1011M-T2 User's Manual Control Panel LEDs The control panel located on the front of the chassis has fi ve LEDs. These LEDs provide you with critical information related to different parts of the system. This section explains what each LED indicates when illuminated and any corrective ac- tion you may need to take.

  • Page 29: Power

    Power: Indicates power is being supplied to the system's power supply units. This LED should normally be illuminated when the system is operating. Serial ATA Drive Carrier LEDs Each Serial ATA drive carrier has two LEDs. Green: When illuminated, the green LED on the front of the SATA drive car- rier indicates drive activity.
  • Page 30 AS1011M-T2 User's Manual Notes...

  • Page 31: Chapter 4: System Safety

    Electrical Safety Precautions Basic electrical safety precautions should be followed to protect yourself from harm and the 1011M-T2 from damage: Be aware of the locations of the power on/off switch on the chassis as well as the room's emergency power-off switch, disconnection switch or electrical outlet.

  • Page 32: General Safety Precautions

    AS1011M-T2 User's Manual Motherboard Battery: CAUTION - There is a danger of explosion if the onboard battery is installed upside down, which will reverse its polarities (see Figure 4-1). This battery must be replaced only with the same or an equivalent type recommended by the manufacturer.

  • Page 33: Esd Precautions

    ESD Precautions Electrostatic discharge (ESD) is generated by two objects with different electrical charges coming into contact with each other. An electrical discharge is created to neutralize this difference, which can damage electronic com ponents and printed circuit boards. The following measures are generally suffi cient to neutralize this difference before contact is made to protect your equipment from ESD: Use a grounded wrist strap designed to prevent static discharge.

  • Page 34: Operating Precautions

    AS1011M-T2 User's Manual Operating Precautions Care must be taken to assure that the chassis cover is in place when the 1011M-T2 is operating to assure proper cooling. Out of warranty damage to the 1011M-T2 system can occur if this practice is not strictly followed. Figure 4-1.

  • Page 35: Chapter 5: Advanced Motherboard Setup

    Advanced Motherboard Setup This chapter covers the steps required to install processors and heatsinks to the H8SMi-2 motherboard, connect the data and power cables and install add-on cards. All motherboard jumpers and connections are described and a layout and quick reference chart are included in this chapter. Remember to close the chassis completely when you have fi...

  • Page 36: Mounting The Motherboard Into A Chassis

    AS1011M-T2 User's Manual Mounting the Motherboard into a Chassis All serverboards and motherboards have standard mounting holes to fi t different types of chassis. Make sure that the locations of all the mounting holes for both the motherboard and the chassis match. Although a chassis may have both plastic and metal mounting fasteners, metal ones are highly recommended because they ground the motherboard to the chassis.

  • Page 37: Installing The Heat Sink

    Chapter 5: Advanced Motherboard Setup 2. Use your thumb and your index fi n- ger to hold the CPU. Locate pin 1 on the CPU socket and pin 1 on the CPU. Triangles Both are marked with a triangle. 3. Align pin 1 of the CPU with pin 1 of the socket.

  • Page 38: Installing The Heatsink Retention Modules

    AS1011M-T2 User's Manual Installing the Heatsink Retention Modules One heatsink retention module (BKT-0005) and two screws are included in the retail box. Once installed, these are used to help attach the heatsink to the CPU. To install, position the module so that the CPU backplate standoffs insert through the holes on the heatsink retention module and the four feet on the module contact the motherboard.

  • Page 39: Connecting Cables

    Connecting Cables Now that the processors are installed, the next step is to connect the cables to the motherboard. These include the data (ribbon) cables for the peripherals and control panel and the power cables. Connecting Data Cables The ribbon cables used to transfer data from the peripheral devices have been carefully routed in preconfi...

  • Page 40: Connecting The Control Panel

    AS1011M-T2 User's Manual Connecting the Control Panel JF1 contains header pins for various front control panel connectors. See Figure 5-2 for the pin locations of the various front control panel buttons and LED indica- tors and refer to section 5-9 for details. Note that even and odd numbered pins are on opposite sides of each header.

  • Page 41: I/O Ports

    I/O Ports The I/O ports are color coded in conformance with the PC 99 specifi cation. See Figure 5-3 below for the colors and locations of the various I/O ports. Figure 5-3. Rear Panel I/O Ports Installing Memory Exercise extreme care when installing or removing memory modules to prevent any possible damage.
  • Page 42 AS1011M-T2 User's Manual Support The H8SMi-2 supports single or dual-channel, DDR2-800/667/533 unbuffered ECC/non-ECC SDRAM. Both interleaved and non-interleaved memory are supported, so you may populate any number of DIMM slots (see note on previous page). Populating two adjacent slots at a time with memory modules of the same size and type will result in interleaved (128-bit) memory, which is faster than non-interleaved (64-bit) memory.

  • Page 43: Adding Pci Cards

    Chapter 5: Advanced Motherboard Setup Adding PCI Cards 1. PCI slots The H8SMi-2 has several PCI expansion slots. The PCI-Express x16 slot may be populated with the use of the CSE-RR1U-E16 riser card, which is included with the system. 2. PCI card installation Before installing a PCI add-on card, make sure it is supported by the riser card (see step 1, above).

  • Page 44: Motherboard Details

    AS1011M-T2 User's Manual Motherboard Details Figure 5-5. H8SMi-2 Motherboard Layout JPW1 Kybd/ Mouse JUSB1 COM1 Parallel Port LAN1 LAN2 Slot #6: PCI-E x16 Slot #5: PCI 33 MHz Slot #4: PCI-E x4 ES1000 Slot #3: PCI-E x8 JPG1 Slot #2: PCI 33 MHz Slot #1: PCI 33 MHz WOR WOL COM2...

  • Page 45: H8Smi-2 Quick Reference

    H8SMi-2 Quick Reference Jumpers Description PS2 Power USB Power JBT1 CMOS Clear JCF1 Compact Flash Master/Slave C1/2 C to PCI Enable/Disable JPG1 VGA Enable/Disable Watch Dog Connectors Description COM1, COM2 COM1/COM2 Serial Port/Header FAN 1-5 System Fan Headers IDE#1 IDE Drive Connector Redundant Power Supply Fail Header 4-pin Auxiliary Power Connector Power Fail Alarm Reset Header...

  • Page 46: Connector Defi Nitions

    AS1011M-T2 User's Manual Connector Defi nitions ATX Power Connector The primary ATX power supply con- nector (J1B1) meets the SSI (Super- set ATX) 24-pin specifi cation. Refer to the table on the right for the pin defi ni- tions of the ATX 24-pin power connec- tor.

  • Page 47: Overheat/Fan Fail Led

    NIC1 LED The NIC1 (Network Interface Control- ler) LED connection is located on pins 11 and 12 of JF1. Attach the NIC1 LED cable to display network activity. Refer to the table on the right for pin defi nitions. NIC2 LED The NIC2 (Network Interface Control- ler) LED connection is located on pins 9 and 10 of JF1.

  • Page 48: Power Button

    AS1011M-T2 User's Manual Power Button The Power Button connection is located on pins 1 and 2 of JF1. Mo- mentarily contacting both pins will power on/off the system. This button can also be confi gured to function as a suspend button (see the Power Button Mode setting in BIOS).

  • Page 49: Atx Ps/2 Keyboard And Mouse Ports

    ATX PS/2 Keyboard and PS/2 Mouse Ports The ATX PS/2 keyboard and the PS/2 mouse ports are located on the IO backplane. The mouse is the top (green) port. See the table on the right for pin defi nitions. Serial Ports The COM1 serial port is located under the parallel port.

  • Page 50: Power Led/Speaker

    AS1011M-T2 User's Manual Power LED/Speaker On JD1, pins 1, 2, and 3 are for the power LED and pins 4 through 7 are for the speaker. See the tables on the right for pin defi nitions. Note: The speaker connector pins are for use with an external speaker.

  • Page 51: Wake-On-Ring

    Wake-On-Ring The Wake-On-Ring header is desig- nated WOR. This function allows your computer to receive and "wake-up" by an incoming call to the modem when in suspend state. See the table on the right for pin defi nitions. You must have a Wake-On-Ring card and cable to use this feature.

  • Page 52: Power Supply Fail Alarm Reset Header

    AS1011M-T2 User's Manual Power Fail Alarm Reset Header Connect JAR to the alarm reset but- ton on your chassis (if available) or to a microswitch to allow you to turn off the alarm that sounds when a power supply module fails. See the table on the right for pin defi...

  • Page 53: 5-10 Jumper Settings

    5-10 Jumper Settings Explanation of Jumpers To modify the operation of the motherboard, jumpers can be used to choose between optional settings. Jumpers create shorts between two pins to change the function of the connector. Pin 1 is identifi ed with a square solder pad on the printed circuit board.

  • Page 54: Vga Enable/Disable

    AS1011M-T2 User's Manual VGA Enable/Disable JPG1 allows you to enable or disable the VGA port. The default position is on pins 1 and 2 to enable VGA. See the table on the right for jumper set- tings. C to PCI Enable/Disable The JI C1/2 pair of jumpers allows you to connect the System Management...

  • Page 55: Onboard Speaker Enable/Disable

    Onboard Speaker Enable/ Disable The JD1 header allows you to use either an external speaker or the in- ternal (onboard) speaker. To use the internal onboard speaker, close pins 6 and 7 with a jumper. To use an external speaker, remove the jumper and connect the speaker wires to pins 4 (+5V) and 7 (control signal).

  • Page 56: 5-11 Onboard Indicators

    AS1011M-T2 User's Manual 5-11 Onboard Indicators LAN1/LAN2 LEDs The Ethernet ports (located beside the VGA port) have two LEDs. On each Gb LAN port, one LED blinks to indicate activity while the other may be green, amber or off to indicate the speed of the connection.

  • Page 57: Floppy, Ide, Parallel Port And Sata Drive Connections

    5-12 Floppy, IDE, Parallel Port and SATA Drive Connections Use the following information to connect the fl oppy and hard disk drive cables. The fl oppy disk drive cable has seven twisted wires. A red mark on a wire typically designates the location of pin 1. A single fl...

  • Page 58: Ide Connector

    AS1011M-T2 User's Manual IDE Connector There are no jumpers to con- fi gure the onboard IDE#1 con- nector unless using it for a compact flash device. the table on the right for pin defi nitions. SATA Ports There are no jumpers to con- fi...

  • Page 59: Parallel Port

    Parallel Port The parallel port is located on the I/O backplane. See the table below for pin defi nitions. Chapter 5: Advanced Motherboard Setup Parallel (Printer) Port Pin Defi nitions Pin# Defi nition Pin # Defi nition Strobe- Auto Feed- Data Bit 0 Error- Data Bit 1...

  • Page 60: 5-13 Enabling Sata Raid

    AS1011M-T2 User's Manual 5-13 Enabling SATA RAID Now that the hardware is set up, you must now install the operating system and the SATA RAID drivers, if you wish to use RAID with your SATA drives. The installation procedure differs depending on whether you wish to have the operating system installed on a RAID array or on a separate non-RAID drive.

  • Page 61: Using The Nvidia Raid Utility

    2. Use the arrow keys to move to the "Advanced" menu, then scroll down to "nVidia RAID Setup" and press the <Enter> key. Once in the submenu, scroll down to "nVidia RAID Function" and enable the setting, which will cause the SATA0/1/2 Primary/Secondary settings to appear.

  • Page 62: 5-14 Installing Drivers

    AS1011M-T2 User's Manual 5-14 Installing Drivers The CD that came bundled with the system contains software drivers, some of which must be installed, such as the chipset driver. After inserting this CD into your CD- ROM drive, the display shown in Figure 2-5 should appear. (If this display does not appear, click on the My Computer icon and then on the icon representing your CD-ROM drive.

  • Page 63: Chapter 6: Advanced Chassis Setup

    Advanced Chassis Setup This chapter covers the steps required to install components and perform mainte- nance on the SC811FT-260 chassis. For component installation, follow the steps in the order given to eliminate the most common problems encountered. If a step is unnecessary, skip ahead to the step that follows.

  • Page 64: Control Panel

    AS1011M-T2 User's Manual Figure 6-1. Chassis Front View Figure 6-2. Chassis Rear View Control Panel The control panel (located on the front of the chassis) must be connected to the JF1 connector on the motherboard to provide you with system control buttons and status indicators.

  • Page 65: System Fans

    Chapter 6: Advanced Chassis Setup System Fans Two 4-cm fans provide the cooling for the 1011M-T2. Each fan unit is actually made up of two fans joined back-to-back, which rotate in opposite directions. This counter- rotating action generates exceptional airfl ow and works to dampen vibration levels. These fans can adjust their speed according to the heat level sensed in the system, which results in more effi...

  • Page 66: Drive Bay Installation/Removal

    AS1011M-T2 User's Manual Drive Bay Installation/Removal Accessing the Drive Bays Serial ATA Drives: Because of their hotswap capability, you do not need to access the inside of the chassis or power down the system to install or replace Serial ATA drives.
  • Page 67 2. Installing/removing hot-swap Serial ATA drives Two Serial ATA drive bays are located in the front of the chassis, making them easily accessible for installation and removal. These drives are hot-swappable, meaning they can be installed and removed without powering down the system. To remove, fi...

  • Page 68: Cd-Rom And Floppy Drive Installation

    AS1011M-T2 User's Manual Serial ATA Backplane The Serial ATA drives plug into a backplane that provides power, drive ID and bus termination. A RAID controller can be used with the backplane to provide data security. The operating system you use must have RAID support to enable the hot- swap capability of the Serial ATA drives.

  • Page 69: Power Supply

    Chapter 6: Advanced Chassis Setup Power Supply The 1011M-T2 has a single 260 watt power supply. This power supply has the capability of operating at 100 - 240 input volts. Depress the main power button on the front of the chassis and then unplug the AC power cord to completely remove power from the system before removing the power supply.
  • Page 70 AS1011M-T2 User's Manual Notes...

  • Page 71: Chapter 7: Bios

    Chapter 7: BIOS Chapter 7 BIOS Introduction This chapter describes the AMIBIOS™ Setup utility for the H8SMi-2. The AMI ROM BIOS is stored in a fl ash chip and can be easily upgraded using a fl oppy disk-based program. Note: Due to periodic changes to the BIOS, some settings may have been added or deleted and might not yet be recorded in this manual.

  • Page 72: Main Menu

    AS1011M-T2 User's Manual Main Menu When you fi rst enter AMI BIOS Setup Utility, you will see the Main Menu screen. You can always return to the Main Menu by selecting the Main tab on the top of the screen with the arrow keys. The Main Menu screen provides you with a system overview, which includes the version, built date and ID of the AMIBIOS, the type, speed and number of the processors in the system and the amount of memory installed in the system.
  • Page 73 Chapter 7: BIOS PS/2 Mouse Support Set this value to allow the PS/2 mouse support to be modifi ed. The options are Enabled, Disabled and Auto. Wait for ‘F1’ If Error Select Enabled to activate the function of Wait for "F1" if Error. T Hit ‘DEL’...

  • Page 74: Cpu Configuration

    AS1011M-T2 User's Manual Power Confi guration Power Button Mode Allows the user to change the function of the power button. Options are On/Off and Suspend. Restore on AC Power Loss This setting allows you to choose how the system will react when power returns after an unexpected loss of power.
  • Page 75 Chapter 7: BIOS Floppy/IDE/SATA Confi guration Floppy A Move the cursor to these fi elds via up and down <arrow> keys to select the fl oppy type. The options are Disabled, 360 KB 5 1/4", 1.2 MB 5 1/4", 720 KB 3½", 1.44 MB 3½”, and 2.88 MB 3½".

  • Page 76: Primary Ide Master/Slave

    AS1011M-T2 User's Manual Primary IDE Master/Slave Highlight one of the items above and press <Enter> to access the submenu for that item. Type Select the type of device connected to the system. The options are Not Installed, Auto, CDROM and ARMD. LBA/Large Mode LBA (Logical Block Addressing) is a method of addressing data on a disk drive.
  • Page 77 DMA Mode Selects the DMA Mode. Options are Auto, SWDMA0, SWDMA1, SWDMA2, MWDMA0. MDWDMA1, MWDMA2, UDMA0. UDMA1, UDMA2, UDMA3, UDMA4 and UDMA5. (SWDMA=Single Word DMA, MWDMA=Multi Word DMA, UDMA=UltraDMA.) S.M.A.R.T. Self-Monitoring Analysis and Reporting Technology (SMART) can help predict impending drive failures. Select "Auto" to allow BIOS to auto detect hard disk drive support.
  • Page 78 AS1011M-T2 User's Manual cannot be determined. Select 0 to allow AMI BIOS to use PIO mode 0. It has a data transfer rate of 3.3 MBs. Select 1 to allow AMI BIOS to use PIO mode 1. It has a data transfer rate of 5.2 MBs. Select 2 to allow AMI BIOS to use PIO mode 2.

  • Page 79: Pcipnp Configuration

    Chapter 7: BIOS PCI/PnP Confi guration Clear NVRAM Select Yes to clear NVRAM during boot-up. The options are Yes and No. Plug & Play OS Select Yes to allow the OS to confi gure Plug & Play devices. (This is not required for system boot if your system has an OS that supports Plug &...

  • Page 80: Super Io Configuration

    AS1011M-T2 User's Manual IRQ3/IRQ4/IRQ5/IRQ7/IRQ9/IRQ10/IRQ11/IRQ14/IRQ15 This feature specifi es the availability of an IRQ to be used by a PCI/PnP device. Select Reserved for the IRQ to be used by a Legacy ISA device. The options are Available and Reserved. DMA Channel 0/Channel 1/Channel 3/Channel 5/Channel 6/Channel Select Available to indicate that a specifi...
  • Page 81 Parallel Port Mode Specify the parallel port mode. The options are Normal, Bi-directional, EPP and ECP. Parallel Port IRQ Select the IRQ (interrupt request) for the parallel port. The options are IRQ5 and IRQ7. Advanced Chipset Confi guration NorthBridge Confi guration In addition to the below settings, the screen lists various clock and timing information.
  • Page 82 AS1011M-T2 User's Manual ECC Confi guration DRAM ECC Enable DRAM ECC allows hardware to report and correct memory errors automati- cally. Options are Enabled and Disabled. 4-Bit ECC Mode Allows the user to enabled 4-bit ECC mode (also known as ECC Chip- kill).
  • Page 83 Chapter 7: BIOS possibility of Electromagnetic Interference. PCIE Spread Spectrum Use this setting to Enable or Disable spread spectrum for the PCIE. SATA Spread Spectrum Use this setting to Enable or Disable spread spectrum for SATA. Primary Graphics Adapter Use this setting to select PCI Express -> PCI or PCI -> PCI Express for the primary graphics adapter.

  • Page 84: Event Log Configuration

    AS1011M-T2 User's Manual MAC1 LAN1 Bridge Settings are Enabled and Disabled for MAC1 LAN1 bridge. Event Log Confi guration View Event Log Highlight this item and press <Enter> to view the contents of the event log. Mark All Events as Read Highlight this item and press <Enter>...

  • Page 85: System Health Monitor

    Chapter 7: BIOS Redirection After BIOS POST Options are Disable (no redirection after BIOS POST), Boot Loader (redirection during POST and during boot loader) and Always (redirection always active). Note that some OS's may not work with this set to Always. Terminal Type Selects the type of the target terminal.
  • Page 86 AS1011M-T2 User's Manual Other items in the submenu are system monitor displays for the following infor- mation: CPU Temperature, System Temperature, CPU1 VCore, 3.3V Vcc (V), +5Vin, +12Vin, 5V Standby and Battery Voltage. View BMC System Event Log Pressing the Enter key will open the event log. Use the "+" and "-" keys to navigate through the system event log.

  • Page 87: Boot Menu

    Boot Menu This feature allows the user to confi gure the following items: Boot Device Priority This feature allows the user to prioritize the boot sequence from the available de- vices. The devices to set are: · 1st Boot Device ·...

  • Page 88: Security Menu

    AS1011M-T2 User's Manual Security Menu AMI BIOS provides a Supervisor and a User password. If you use both passwords, the Supervisor password must be set fi rst. Change Supervisor Password Select this option and press <Enter> to access the sub menu, and then type in the password.

  • Page 89: Load Optimal Defaults

    Chapter 7: BIOS Load Optimal Defaults To set this feature, select Load Optimal Defaults from the Exit menu and press <Enter>. Then Select "OK" to allow BIOS to automatically load the Optimal Defaults as the BIOS Settings. The Optimal settings are designed for maximum system performance, but may not work best for all computer applications.
  • Page 90 AS1011M-T2 User's Manual Notes 7-20...

  • Page 91: Appendix A: Bios Error Beep Codes

    Appendix A BIOS Error Beep Codes During the POST (Power-On Self-Test) routines, which are performed each time the system is powered on, errors may occur. Non-fatal errors are those which, in most cases, allow the system to continue the boot-up process. The error messages normally appear on the screen. Fatal errors are those which will not allow the system to continue the boot-up pro- cedure.
  • Page 92 AS1011M-T2 User's Manual Notes...

  • Page 93: Appendix B: Bios Post Checkpoint Codes

    BIOS POST Checkpoint Codes When AMIBIOS performs the Power On Self Test, it writes checkpoint codes to I/O port 0080h. If the computer cannot complete the boot process, diagnostic equipment can be attached to the computer to read I/O port 0080h. Uncompressed Initialization Codes The uncompressed initialization checkpoint codes are listed in order of execution: Checkpoint...

  • Page 94: Bootblock Recovery Codes

    AS1011M-T2 User's Manual Bootblock Recovery Codes The bootblock recovery checkpoint codes are listed in order of execution: Checkpoint Code Description The onboard fl oppy controller if available is initialized. Next, beginning the base 512 KB memory test. Initializing the interrupt vector table next. Initializing the DMA and Interrupt controllers next.
  • Page 95 Uncompressed Initialization Codes The following runtime checkpoint codes are listed in order of execution. These codes are uncompressed in F0000h shadow RAM. Checkpoint Code Description The NMI is disabled. Next, checking for a soft reset or a power on condition. The BIOS stack has been built.
  • Page 96 AS1011M-T2 User's Manual Checkpoint Code Description Interrupt vector initialization is done. Clearing the password if the POST DIAG switch is on. Any initialization before setting video mode will be done next. Initialization before setting the video mode is complete. Confi guring the mono- chrome mode and color mode settings next.
  • Page 97 Checkpoint Code Description The memory below 1 MB has been cleared via a soft reset. Clearing the memory above 1 MB next. The memory above 1 MB has been cleared via a soft reset. Saving the memory size next. Going to checkpoint 52h next. The memory test started, but not as the result of a soft reset.
  • Page 98 AS1011M-T2 User's Manual Checkpoint Code Description The password was checked. Performing any required programming before WIN- BIOS Setup next. The programming before WINBIOS Setup has completed. Uncompressing the WINBIOS Setup code and executing the AMIBIOS Setup or WINBIOS Setup utility next.
  • Page 99 Checkpoint Code Description Returned from adaptor ROM at E000h control. Performing any initialization required after the E000 option ROM had control next. Initialization after E000 option ROM control has completed. Displaying the system confi guration next. Uncompressing the DMI data and executing DMI POST initialization next. The system confi...
  • Page 100 AS1011M-T2 User's Manual Notes...

  • Page 101: Appendix C: System Specifi Cations

    Appendix C: System Specifi cations Appendix C System Specifi cations Processors Single AMD Opteron Series 1000 processor in a 940-pin AM2 socket Note: Please refer to our web site for a complete listing of supported processors. Chipset nVidia MCP55 Pro chipset BIOS 4 Mb AMI BIOS®...
  • Page 102 AS1010S-T User's Manual Motherboard Model: H8SMi-2 (ATX form factor) Dimensions: 8 x 12 in (203 x 305 mm) Chassis Model: SC811FT-260 Form Factor: 1U rackmount Dimensions: (WxHxD) 16.8 x 1.7 x 22.6 in. (426 x 43 x 574 mm) Weight Gross (Bare Bone): 35 lbs.

  • Page 103: Regulatory Compliance

    Appendix C: System Specifi cations Regulatory Compliance Electromagnetic Emissions: FCC Class B, EN 55022 Class B, EN 61000-3-2/-3-3, CISPR 22 Class B Electromagnetic Immunity: EN 55024/CISPR 24, (EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-4-8, EN 61000-4-11) Safety: EN 60950/IEC 60950-Compliant, UL Listed (USA), CUL Listed (Canada), TUV Certifi...
  • Page 104 AS1010S-T User's Manual Notes...

Table of Contents