Cab Layout & Controls - jcb 406 Quick Start Manual

Lifting Points
Fig 7
P
P
E
E
N
N
J
J
K
K
P
P
L
L
A H beam lifting spreader
B Centre line - centre of gravity
C Centre line - machine lifting point
D Lifting chain 5° minimum angle
E Lifting Chain 15° maximum angle
F Lifting chain 5° minimum angle
(To avoid damaging the machine)
G Lifting chain 15° Maximum angle
111
111
10 Please see operator manual for full details.
Operation
Operation
Lifting a Machine
Lifting a Machine
B
A
B
A
P P
P
P
C
P
C
C
C P
D
D
F
F
G
G
H
H
Fig 84. Lifting (Side View)
Fig 84. Lifting (Side View)
A
N
N
N
A
N
N
N J
J
J
J
K
K
K
K
K
K
P
P
P
P
P
P
M
M
Fig 85. Lifting (End Views)
H Centre of gravity (For illustration only -
Fig 85. Lifting (End Views)
the position on your machine may vary)
J 0° angle maximum (Not shown)
K 5° Maximum angle
L Front of machine
M Rear of machine
N Perpendicular line - machine lifting point
P Lifting chain
9821-9350-5
9821-9350-5
Cab Layout
Fig 8
Park Brake Lever - 406 and 407 Machines Only
Important: No attempt must be made to adjust the park
brake using the lever handle. The handle adjustment must
remain permanently screwed all the way in.
1 Use this lever to engage the park brake 5 before
leaving the machine.
A
B
Note: The transmission
disconnected when the park brake is engaged. 406 & 407
Drive Controls, Switches and Instruments
Park Brake Lever - 406 and 407 Machines Only Park Brake Lever - 407HS and 409 Machines Only
The park brake must not be used to slow the machine
Important: No attempt must be made to adjust the park 1 from travelling speed, except in an emergency, You must apply the park brake C before you leave the
brake using the lever handle. The handle adjustment must otherwise the efficiency of the brake will be reduced. cab. K Fig 32. ( T
remain permanently screwed all the way in.
4-2-1-8
1 Use this lever to engage the park brake 5 before 2 To engage the park brake, pull the lever A up as far
as it will go (vertical). Check that the indicator light
leaving the machine. K Fig 32. ( T 42) D
comes on.
A 3 To release the park brake, squeeze the release lever
B and lower the lever fully. Check that the indicator
light goes out.
Note: The park brake off and operator out of seat warning
will display after the operator leaves the seat if the park
brake is off. The buzzer will also sound. To cancel the fault
and buzzer apply the park brake.
T070350-31
B
T070350-31
Note: The transmission drive is automatically
disconnected when the park brake is engaged.
409 ONLY
!M CAUTION
The park brake must not be used to slow the machine
from travelling speed, except in an emergency,
otherwise the efficiency of the brake will be reduced.
Note: When the park brake is applied, the transmission
4-2-1-8 drive is disconnected automatically.
2 To engage the park brake, pull the lever A up as far
!M
as it will go (vertical). Check that the indicator light
comes on. 1.
The park brake must not be used to slow the machine Steering Wheel
from travelling speed, except in an emergency,
3 To release the park brake, squeeze the release lever
otherwise the efficiency of the brake will be reduced.
45
B and lower the lever fully. Check that the indicator
4-2-1-8
light goes out.
2.
Accelerator pedal
2 To apply the park brake, press the park brake lever
Note: The park brake off and operator out of seat warning
button D and pull the lever upwards firmly until the
will display after the operator leaves the seat if the park
park brake is engaged. Release the lever button and
brake is off. The buzzer will also sound. To cancel the fault
make sure the lever is firmly engaged before
3.
and buzzer apply the park brake. Foot Brake
removing your hand. Make sure that the park brake is
sufficiently engaged to prevent the machine moving.
Note: Using the park brake lever button when applying the
4.
park brake will prevent premature wear on the park brake Forward/ Reverse Switch
ratchet mechanism
Make sure that the park brake indicator light on the
5. front console comes on.
Park Brake Lever
6.
Instrument Cluster
7.
Right Hand console
45 9821-9350-5
8.
Operating Levers
9.
Ignition Switch
10.
Creep Speed
11.
T070350-32
Rotary Throttle (Option)
T070350-32
12.
Horn
13.
Multi Purpose Steering
Column Switch
14.
CAB Interior Light
15.
Speakers
16.
Front Window Blind
17.
Steering column Adjustment.
111
111
Cab Layout
Component Key
The cab component layout illustration shows a typical
Operation
machine. Your machine may look different to the model
Drive Controls, Switches and Instruments
shown.
Park Brake Lever - 407HS and 409 Machines Only
1 You must apply the park brake C before you leave the
cab. K Fig 32. ( T 42).
K Fig 32. ( T 42)
D
6
C
1
20 21
A
B 45 C
% a
15 e
Aux 1
1870
rpm b
26.5
d mph 09876.4
c
12 13 14 17 18
1 2 3 4 5 6 7 8 9 10
drive is automatically
Operation
12
!M
CAUTION
P1062300-2
Fig 34.
42).
Note: When the park brake is applied, the transmission
drive is disconnected automatically.
!M
CAUTION
The park brake must not be used to slow the machine
from travelling speed, except in an emergency,
otherwise the efficiency of the brake will be reduced.
4-2-1-8
C
2 To apply the park brake, press the park brake lever 3
button D and pull the lever upwards firmly until the
park brake is engaged. Release the lever button and
make sure the lever is firmly engaged before
removing your hand. Make sure that the park brake is
sufficiently engaged to prevent the machine moving.
Note: Using the park brake lever button when applying the
park brake will prevent premature wear on the park brake
ratchet mechanism
Make sure that the park brake indicator light on the
front console comes on.
P1062300-2
Fig 34.
5
CAUTION
45
9821-9350-5
Fig 32.
45
16
42
9821-9350-5
1 K Steering Wheel ( T 44)
2 K Accelerator Pedal ( T 44)
3 K Foot Brake Pedal ( T 44)
4 K Forward/Reverse Switch ( T 46)
Operation
Cab Layout
13
16
19
11
8
4
17
7
10
2
9
11
Operation
T024940-12
Cab Layout
14
15
42
T052380-5
Fig 33.
11 K Rotary Throttle Control (Option) ( T 47)
12 K Horn ( T 47)
406, 407 & 409
13 K Multi-Purpose Steering Column Switch ( T 48)
14 K Cab Interior Light ( T 53)
11