Advertisement
KS-AX5101D
Subwoofer system
• Use the speakers with an impedance of 2 Ω to 8 Ω.
Speaker input connector.
Connector lead
To
Receiver
= Front left (+) lead
• White "Left (+)"
= Front left (-) lead
• White (Stripe) "Left (-)"
= Front right (+) lead
• Gray "Right (+)"
= Front right (-) lead
• Gray (Stripe) "Right (-)"
R
2-Subwoofer system (2 amplifiers)
• Use the speakers with an impedance of 2 Ω to 8 Ω.
• Incoming signals from INPUT jacks are emitted through the PRE OUT jacks.
Speaker input connector.
Connector lead
• White "Left (+)"
• White (Stripe) "Left (-)"
• Gray "Right (+)"
• Gray (Stripe) "Right (-)"
JVC car receiver, etc.
Line out (Rear)
or
*
2
Subwoofer out
2-Subwoofer system
• Use the speakers with an impedance of 4 Ω to 8 Ω.
Speaker input connector.
Connector lead
To
Receiver
= Front left (+) lead
• White "Left (+)"
= Front left (-) lead
• White (Stripe) "Left (-)"
= Front right (+) lead
• Gray "Right (+)"
= Front right (-) lead
• Gray (Stripe) "Right (-)"
Notes
• Check the impeadance
of subwoofer before
connecting it.
5-speaker system plus subwoofer—5.1-channel (3 amplifiers)
• Use the speakers with an impedance of 2 Ω to 8 Ω.
• Be sure to connect the line output from the receiver to the left (L) jack on this unit.
JVC car receiver, etc.
Line out
Subwoofer out
(Center)
*
2
*
2
R
Speaker input connector.
Connector lead
To
= Front left (+) lead
• White "Left (+)"
= Front left (-) lead
• White (Stripe) "Left (-)"
= Front right (+) lead
• Gray "Right (+)"
= Front right (-) lead
• Gray (Stripe) "Right (-)"
SPECIFICATIONS
Power Output
• Normal Mode:
70 W RMS × 4 channels at 4 Ω and ≤ 1% THD + N
80 dBA (reference: 1 W into 4 Ω)
Signal-to-Noise Ratio
Power Output
• Normal Mode:
100 W RMS × 4 channels at 2 Ω and ≤ 1% THD + N
• Bridge Mode:
200 W RMS × 2 channels at 4 Ω and ≤ 1% THD + N
Maximum Power Output
1000 W (500 W × 2)
Load Impedance
• Normal Mode:
4 Ω (2 Ω to 8 Ω allowance)
• Bridge Mode:
4 Ω (4 Ω to 8 Ω allowance)
Frequency Response
5 Hz to 50,000 Hz ( +0 dB, –3 dB)
Input Sensitivity/Impedance
2 V/20 kΩ (0.25 V to 5 V, variable)
Distortion
Less than 0.04% (at 1 kHz)
Power Requirement
DC 14.4 V (11 V to 16 V allowance)
Grounding system
Negative ground
Dimensions (W×H×D)
310 mm × 60 mm × 300 mm
1
(12-
/
in. × 2-
4
Mass (approx.)
3.2 kg (7.1 lbs)
Design and specifications are subject to change without notice.
JVC car receiver, etc.
Line out (Rear)
or
Subwoofer out
*
2
R
Subwoofer
To
Receiver
= Front left (+) lead
= Front left (-) lead
= Front right (+) lead
= Front right (-) lead
*
2
*
2
JVC car receiver, etc.
Line out (Rear)
or
Subwoofer out
*
2
Subwoofer
*
2
JVC amplifier, etc.
(Purchased separately)
*
2
Front
Speaker
JVC amplifier, etc.
Center Speaker
(Purchased separately)
Receiver
KS-AX5104
3
13
/
in. × 11-
/
in.)
8
16
Not supplied
*
2
CONTROLS
KS-AX5104
KS-AX5102
1 Input LEVEL controller
The input level can be adjusted with this control when this unit is connected to other source
Subwoofer
equipment. Adjust the level while listening to the sound. This control is preset to MIN when
the unit is shipped.
2 BASS BOOST controller
Turning this boosts the 45 Hz frequency within the range of 0 dB to +18 dB. Adjust the level
Subwoofer
while listening to the sound. This controller is preset to MIN when the unit is shipped.
3 CROSSOVER frequency controller
Turning this adjusts the cutoff frequency within the range of 50 Hz to 200 Hz. Adjust the level while
listening to the sound. This control is preset to 50 Hz when the unit is shipped.
4 CROSSOVER filter switch
OFF: N ormally set to this position. The switch is preset to this position when the unit is shipped.
LPF: S et to this position when you want to turn on the LPF (Low-Pass Filter) switch.
HPF: S et to this position when you want to turn on the HPF (High-Pass Filter) switch.
5 POWER lamp
The green lamp lights while the unit is turned on.
PROTECT lamp
If the lamp lights in red with the unit on, some trouble has occurred (see "TROUBLE SHOOTING").
TROUBLESHOOTING
For more details, consult your JVC car audio dealer.
The POWER lamp does not light.
• Change the fuses if the current one is blown.
• Connect the ground lead securely to a metal part of the car.
• Turn on the equipment connected to this unit.
Subwoofer
• Use a relay if your system employs too many amplifiers.
• Confirm the battery voltage (11 V to 16 V).
The PROTECT lamp lights in red and/or the unit heats up abnormally.
• Use the speakers of suitable impedance.
• Correct the speaker wirings if they are short-circuited.
• Make the speaker wirings away from the power cord to prevent DC offset error.
• Leave the unit turned off for a while to cool it down.
No sound is heard.
• Confirm the connections for the power supply (see "POWER SUPPLY" on page 1).
• Connect RCA pin cords to the INPUT jacks, or the speaker input connector to the HIGH INPUT terminal.
Rear
Speaker
Alternator noise is heard.
• Keep the power cords away from the RCA pin cords.
• Keep the RCA pin cords away from other electrical cables in the car.
• Connect the ground lead securely to a metal part of the car.
• Make sure the negative speaker leads do not touch the car chassis.
• Replace the plugs or use plugs with load resistors.
• Connect a bypass capacitor across the accessory switches (horn, fan, etc.).
• Connect the LINE NOISE FILTER (commercially available) between Line Output (through the receiver)
and INPUT jacks on this unit.
Noise is made when you connect the unit to an AM tuner.
Subwoofer
• Move the speaker and power cords away from the antenna lead.
KS-AX5102
100 W RMS × 2 channels at 4 Ω and ≤ 1% THD + N
80 dBA (reference: 1 W into 4 Ω)
150 W RMS × 2 channels at 2 Ω and ≤ 1% THD + N
300 W RMS × 1 channels at 4 Ω and ≤ 1% THD + N
600 W
4 Ω (2 Ω to 8 Ω allowance)
4 Ω (4 Ω to 8 Ω allowance)
5 Hz to 50,000 Hz ( +0 dB, –3 dB)
2 V/20 kΩ (0.25 V to 5 V, variable)
Less than 0.04% (at 1 kHz)
DC 14.4 V (11 V to 16 V allowance)
Negative ground
260 mm × 60 mm × 300 mm
1
3
13
(10-
/
in. × 2-
/
in. × 11-
/
in.)
4
8
16
2.6 kg (5.8 lbs)
3
FRONT
REAR
KS-AX5101D
KS-AX5101D
300 W RMS × 1 channels at 4 Ω and ≤ 1% THD + N
60 dBA (reference: 1 W into 4 Ω)
500 W RMS × 1 channels at 2 Ω and ≤ 1% THD + N
—
1000 W
4 Ω (2 Ω to 8 Ω allowance)
—
20 Hz to 200 Hz ( +0 dB, –3 dB)
2 V/20 kΩ (0.25 V to 5 V, variable)
Less than 0.08% (at 100 Hz)
DC 14.4 V (11 V to 16 V allowance)
Negative ground
260 mm × 60 mm × 300 mm
1
3
13
(10-
/
in. × 2-
/
in. × 11-
4
8
2.7 kg (6.0 lbs)
/
in.)
16
Advertisement
