Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Emergency Caller Products Manuals
  4. Security System
  5. EC-4
  6. Programming manual

Emergency Caller Products EC4 Programming Manual

Dialer
Hide thumbs Also See for EC4:

Advertisement

Quick Links

Download this manual
1-800-227-1592 www.emergencycaller.com
EC4 Dialer Programming Guide
This guide is to help you program
your EC4 product.
(SEE QUICK REFERENCE GUIDE FOR CONDENSED VERSION)
Programming Emergency Numbers
1. Apply power to your EC4. Plug your AC-2P power supply
into wall outlet. Make sure the AC-2P is plugged into the top
of your EC4.
LCD Display Will Show
2. Press 1 to add the first phone number to call
LCD Display Will Show

Advertisement

loading

Related Manuals for Emergency Caller Products EC4

Summary of Contents for Emergency Caller Products EC4

  • Page 1 EC4 product. (SEE QUICK REFERENCE GUIDE FOR CONDENSED VERSION) Programming Emergency Numbers 1. Apply power to your EC4. Plug your AC-2P power supply into wall outlet. Make sure the AC-2P is plugged into the top of your EC4. LCD Display Will Show 2.
  • Page 2 1-800-227-1592 www.emergencycaller.com 3. Press 1 Again LCD Display Will Show 4. Press “2 for No”. If you are going to send emergency message to a pager number, press 1 for yes to add pager number. See Pager number programming below if needed. LCD Display Will Show If you are entering more than one phone number, you must select the location for each number Example: Select 1 for your first...
  • Page 3 1-800-227-1592 www.emergencycaller.com Emergency number, Select 2 for your second number, Select 3 for the third and so on. Dialer will take up to 8 telephone, cellphone or pager emergency numbers You now can enter up to 8 phone numbers. Enter each phone number one by one.
  • Page 4 1-800-227-1592 www.emergencycaller.com If you entered the wrong number, the dialer cannot cycle backwards, only forward. If this happens just hit the * button and continue with Step 2 by entering the location for number to correct (1-8). Wrong numbers can be over written by going through the same process again.
  • Page 5 1-800-227-1592 www.emergencycaller.com LCD will display: Press 1 (TONE) if you are using a standard telephone line with a dial tone. (Dialer is Pre-set to TONE). Press 2 (PULSE) if you are using a telephone line that uses pulse relay to dial out. (Typically Not Used) LCD will display This step is where you will program the digit to dial out in order to get an outside line or dial tone.
  • Page 6 1-800-227-1592 www.emergencycaller.com If your phone system requires dialing a digit to get an outside line or dial tone, Press 1 (ON). If your phone system does not require a digit to get an outside line or dial tone, Press 2 (OFF). If you pressed 1 (ON) LCD will display Enter the number to dial out (1 digit)
  • Page 7 1-800-227-1592 www.emergencycaller.com You can control how many times the dialer will call each emergency numbers that you programmed into your EC4 Emergency Caller. Enter desired number of attempts. (Dialer is Pre-set to 2 attempts). LCD will display You can control the number of Out Going Messages (OGM’s) that will be delivered to each number.
  • Page 8 1-800-227-1592 www.emergencycaller.com 6. Press 1 (YES) to program Emergency Caller Out Going Message (OGM) LCD will display: Press 2 (NO) LCD will display Press 1 (YES) LCD will display...
  • Page 9 1-800-227-1592 www.emergencycaller.com This is where you will record your emergency message that will notify all phone numbers of your need for help. Before recording, it is recommended to write down what your OGM will say. Hold the Dialer 6 inches away from you. Prepare yourself to speak directly at the small MIC on the left side of the Dialer.
  • Page 10 1-800-227-1592 www.emergencycaller.com Press 1 (YES) to listen to your OGM that you recorded. After the OGM has been played, the LCD will display: Press 1 (YES) if you are satisfied with your OGM. Press 2 (NO) if you wish to re-record your OGM and it will bring you back to: Follow the steps above from Step 6 until you are satisfied with recording your OGM.
  • Page 11 1-800-227-1592 www.emergencycaller.com Disabling the MIC will turn off the One-way and two-way communication. Press 1 (YES) if you want to disable the One-way and two-way communication Press 2 (NO) to turn On the One-way and two-way communication. For more information regarding the One-way and Two-way communication feature, please refer to the Additional Features section on the set up guide.
  • Page 12 LCD will display This step is where you must program your input channels for Normally Open (N.0) or Normally Closed (N.C) contact activation. If you purchased the EC4 Emergency Caller with a Transmitter(s), they have been programmed at the factory. Special Note: To Add P4S &...
  • Page 13 1-800-227-1592 www.emergencycaller.com Press 1 (YES) to enable Channel 1 Press 2 (NO). LCD will display Note: Entry – Exit Option Entry / Exit Delay is an option of the Emergency Caller. We recommend not activating this feature with our Emergency Caller product.
  • Page 14 1 (YES) N.O. is Normally Open and N.C. is Normally Closed EC4 products are set N.C. Normally Closed If you purchased the EC4, Press 2 (N.C.). LCD will display MOM is Momentary and CONT is Continuous. EC4 products are set to (MOM) Momentary.
  • Page 15 1-800-227-1592 www.emergencycaller.com Press 1 (MOM). LCD will display This setting will dial all the phone numbers that you have programmed. Make sure you hit "1 (YES)" for all the phone numbers you want the dialer to call. LCD will display: 8.
  • Page 16 Note (If you purchased more than One Transmitter) Keep in mind that each channel can only support one transmitter. (The EC4 dialer has 4 channels) If you have purchased more than one transmitter, you must Select: 1 Channel 1 for the first transmitter...
  • Page 17 *Note: If for any reason the Dialer automatically Dials out without triggering a transmitter, pay close attention to Step 8: CH 1: N.O./ N.C. You want to set is as N.C. for all EC4 Transmitters. The dialer will now monitor any alarm activation.
  • Page 18 1-800-227-1592 www.emergencycaller.com The screen will automatically change within 3 seconds and the LCD will display Press 2 (NO). The LCD will display:...
  • Page 19 3, Select 4 for channel 4 The LCD will display If you are using the EC4 transmitter then select 1. This is where you can select each channel and view step by step what has been programmed and saved. It will also display all the phone numbers you have saved and will display them one phone number at a time.
  • Page 20 1-800-227-1592 www.emergencycaller.com When you are satisfied and want to go back to the "OPERATE" mode, simple press 0 (DONE) then press the "M" button until the LCD will Display "OPERATE" Your phone numbers have been tested and EC4 is active.
  • Page 21 1-800-227-1592 www.emergencycaller.com...