Table 65 - Warning Description Table - Johnson Controls 100 Series Installation Operation & Maintenance

FORM 100.50-NOM12
ISSUE DATE: 04/02/2019

TABLE 65 - WARNING DESCRIPTION TABLE

HISTORY
SCREEN
WORDING
Building static pres> 0.45" W.C. or <
WRN-BUILDING
-0.45" W.C. for 10 seconds. Power
PRS
exhaust reverts to none or on/off
WRN-CO2
Outside CO
SENSOR 1
15 minutes
OUTSIDE
WRN-CO2
Outside CO
SENSOR 2
15 minutes
INSIDE
WRN-COMPR
SYSTEM * See description at the end of this table
INHIBIT
WRN-DIRTY The filter status input is closed for >= 1
FILTER 1 minute
WRN-
The discharge pressure for that system
DISCHARGE PRS
is out of range for >= 10 seconds
SENSOR *
Supply fan output on, supply fan status
WRN-DUCT PRS must be running for 5 minutes, static
XDCR press current <=(0.333 X duct static
press active sp) for 30 seconds
The exhaust fan output is on for 45
WRN-EXHAUST
seconds and the run verification input is
FAN
low (open) for 10 seconds
WRN- The hw/steam freezstat circuit goes
FREEZESTAT high (closed) but goes low (open) within
TRIP 5 minutes
On modulating gas the heat binary
WRN-FURNACE
outputs do not match the gas furnace
MULTIPLEXER status input. See Table 63 on page
FAULT 169 for furnace status input on staged
heat
The heat binary outputs do not match
WRN-GAS
the gas furnace status input. See Table
FURNACE
63 on page 169
WRN-HET The heat entering sensor is out of range
SENSOR for >= 10 seconds
Both compressor are on for the system
WRN-HIGH DP and the discharge press is >= to the
UNLOAD *# system unloading pressure for 10
seconds
WRN-LOW The outdoor temp is <= to the mech
AMBIENT TEMP * cool lockout temp
WRN-LOW The suction temp is less than the
SUCTION TEMP
suction temp low limit for 10 continuous
*# seconds
JOHNSON CONTROLS
DESCRIPTION
sensor out of range for >=
2
sensor out of range for >=
2
SHOW WHEN
RESET
UNIT TYPE IS
Power Exhaust
Auto Other Than
Reset None Or On - Off
Damper
Auto Ventilation Control
Reset Equals Demand
Auto Ventilation Control
Reset Equals Demand
Auto
Reset
Auto Dirty Filter Switch
Reset Is Installed
Press Trans Pkg
Auto
Is On For The
Reset
System
Auto Unit Type Is VAV
Reset Or FlexSys
Auto Power Exhaust
Reset Other Than None
Heating System
Auto
Type Equals Hot
Reset
Water Steam
Heating System
Auto Type Equals
Reset Modulating Gas Or
Staged Gas
Heating System
Auto
Type Equals
Reset
Staged Gas
Heating System
Auto
Type Is Staged
Reset
Gas Or Electric
Press Trans Pkg
Auto
Is On For The
Reset
System
Low Ambient Pkg
Auto
Is Not Installed For
Reset
The System
Auto
Reset
SECTION 8 – SERVICE
STATUS FAULT
SCREEN OUTPUT
WORDING TYPE
Exhaust Sensor/
Sys Status Misc
Warning Fault
Ventilation Sensor/
Sys Status Misc
Warning Fault
Ventilation Sensor/
Sys Status Misc
Warning Fault
Cooling
Heating
Fault
Sensor/
Filter Status
Misc
Change
Fault
Sensor/ Sensor/
Misc Status Misc
Warning Fault
Supply
Sys Status Fan Fault
Warning
Exhaust Sensor/
System Status Misc
Warning Fault
Sensor/ Cooling
Misc Status Heating
Warning Fault
Sensor/ Cooling
Misc Status Heating
Warning Fault
Cooling
Heating
Fault
Sensor/ Sensor/
Misc Status Misc
Warning Fault
Sensor/ Sensor/
Misc Status Misc
Warning Fault
Comp Sys * Sensor/
Status Low Misc
Amb Inhibit Fault
Comp Sys * Sensor/
Status Suction Misc
Temp Unl # On Fault
175
8