Summary of Contents for Maguire Products S-BLENDER
- Page 1 Maguire S Blender Maguire Products, Inc. MAGUIRE PRODUCTS INC. Weigh Scale Blender S - BLENDER • SUPPLIMENTAL DOCUMENTATION Copyright Maguire Products, Inc. 2007...
- Page 2 Maguire S Blender Maguire Products, Inc.
- Page 3 The information contained within this manual including any translations thereof, is the property of Maguire Products Inc. and may not be reproduced, or transmitted in any form or by any means without the express written consent of Maguire Products Inc.
-
Page 4: Table Of Contents
Re-Installation of the Mix Chamber and Mix Blade Weigh Bin Assembly Removal, Inspection, Cleaning Re-Installation of the Weigh Bin Assembly Sensor Adjustment Weigh Bin Door Flow Control Adjustment Dimensional Drawings S-Blender Nomenclature / Order Code Technical Support and Contact Information... -
Page 5: Maguire S-Blender
Maguire S Blender Maguire Products, Inc. Maguire S-Blender Special Purpose Blender High Temperature The “S” Blender is a special purpose blender designed for applications where the clearance between the machine throat and the drying hopper is limited (typically no more than 84 inches [213 cm]). The S Blender is supplied without a “natural”... -
Page 6: Mix Chamber Removal, Inspection, Cleaning
Maguire S Blender Maguire Products, Inc. Mix Chamber Removal, Inspection, Cleaning The Mix Chamber is accessible though the Front Door Assembly. The Front Door Assembly is secured to the frame assembly with 2 latches. The upper half of the Front Door Assembly is keyed into a Safety Interlock Switch. -
Page 7: Re-Installation Of The Mix Chamber And Mix Blade
Maguire S Blender Maguire Products, Inc. 4. Remove the Mix Chamber. Note that the Mix Chamber dump port is closer to the Front Door Assembly. This opening at the base of the Mix Chamber must be re-installed in the same... -
Page 8: Weigh Bin Assembly Removal, Inspection, Cleaning
Maguire S Blender Maguire Products, Inc. Weigh Bin Assembly Removal, Inspection, Cleaning The Weigh Bin Assembly is accessible though the Back Door Assembly. The Back Door Assembly is secured to the frame assembly with 2 latches. 1. To access the Weigh Bin Assembly, un-hook the latch, and gently lower the hinged Back Door Assembly down onto the Mix Motor. -
Page 9: Re-Installation Of The Weigh Bin Assembly
Maguire S Blender Maguire Products, Inc. Re-Installation of the Weigh Bin Assembly 1. To re-install the Weigh Bin, hold the dump flap closed while guiding the weigh bin into the Frame Assembly. Orient the Weigh Bin so that the Dump Valve air hose is to the left and closest to you. -
Page 10: Sensor Adjustment
Maguire S Blender Maguire Products, Inc. Sensor Adjustment Location: Below the weigh bin door, next to the mix motor. Calibration: With the mix chamber EMPTY, press and hold the button located on the Sensor using a pen. Continue to hold the button until the sensors green light blinks TWICE then release the button. -
Page 11: Dimensional Drawings
Maguire S Blender Maguire Products, Inc. Dimensional Drawings... -
Page 12: S-Blender Nomenclature / Order Code
Maguire Products, Inc. S-Blender Nomenclature / Order Code The S-Blender identification plate is located on the left side of the Blender if you are facing the Front Door Assembly (access panel to Mix Chamber). This plate has specific information about your S-Blender including: Product Classification / Model Series / Slide Gate Options / Batch Size / Voltage / Amp Rating. -
Page 13: Technical Support And Contact Information
Tame Park Tamworth Staffordshire B775DY Tel: + 44 1827 265 850 Fax: + 44 1827 265 855 Maguire Products Asia PTE LTD 45 Kallang Pudding Road #01-02 Alpha Building Singapore 349317 Tel: +65 6848 7117 Fax: +65 6744 3370 Email:...