Advertisement
Available languages
Available languages
4 English
7. SECURITy TIPS
l Obey absolutely valid regulations on the electrical security
l Never run pump dry
l Pumping inflammable, as well as all other aggressive
liquids is prohibited
l Pay attention to the medium temperature max. 35°C
l Never pull the pump on the electrical cable or pressure
hose l Avoid cross section narrowing
l Pay attention to the given particle size
l During longer unused times, clean the pump, wash it out
with clear water, dry and store it at room temperature
l Test wells for enough flowing water (dry run danger)
l The pump is to be secured through a RCD circuit breaker
with a release current
of 30 mA.
l The electrical connections are always to be carried out by an
authorised professional.
l The pump may be used by children aged 8 years and
above as well as persons with reduced physical, sensory
or mental abilities or those who lack skills, experience and
knowledge only if they are supervised. These aforementi-
oned persons should only use the appliance while adhering
to safe instructions and resulting dangers.
l Cleaning and maintenance must not be carried out by child-
ren without supervision.
l The pump must not be used or operated under any circum-
stances when there are people in the same water.
l Under certain cirumstances, it is possible that that contami-
nation of water is caused by leakage.
ThE MANUFACTURER EXPLAINS:
l To take over no responsibility in the case of accidents or damages
on the basis of carelessness or disregard to the instructions in this
book.
l To reject every responsibility for the damages which originate
from the improper use of the pump.
8. RECOGNISING AND REPAIRING OF MISTAKES
Problem
Possible cause
Air in the suction line
Pump runs, no water is being
pumped
Air in the system (cannot escape)
Impeller wheel is blocked
Engine guard has switched the pump off
Pump does not start or swit-
ches itself off
No electricity
Pump is inserted to deep
Hose connections systems have a leak
Pump runs, Pump capacity
slows down or stops
Impeller wheel is worn down
Filter has become dirty
Pump could have a leak
When you turn on the pump,
RCD circuit
Condensation in the electrical connection /
breaker is triggered
junction box
9. NOTES ON PRODUCT LIABILITy
We point out, that we are only liable for damages under the Product Liability Act, which are caused by our units if
no changes were made to the equipment. If repairs are carried out by our authorized service, we are only liable if
original spare parts and accessories were used.
10. NOTES ON DISPOSAL
Electro devices of our company, labeled with the symbol of the crossed trash bin, are not permitted to
be disposed in your household garbage. We are registered at the German registration department EAR
under the WEEE-No. DE25523173. This symbol means, that you're not allowed to treat this product as a
regular household waste item – it has to be disposed at a recycling collection point of electrical devices.
This is the best way to save and protect our earth.
ThANK yOU FOR yOUR SUPPORT!
11. EU DECLARATION OF CONFORMITy
The undersigned 1A Profi Handels GmbH, Unterriethstr. 37, 65187 Wiesbaden confirms, that the products placed
on the market execution referred to the relevant regulations below, the relevant EU directives and harmonized corre-
sponds to the EU standard for security.
This declaration is valid insofar as no changes to the product are made.
Low Voltage Directive (2006/95/EC)
Low Voltage Directive (2006/95/EC)
EC Electromagnetic compatibility directive (2004/108/EC)
The following harmonized standards:
EN ISO 12100:2010, EN 809:1998+A1:2009,
EN 60204-1:2006+A1:2009+AC:2010, EN 60335-1:2012,
EN 60335-1:2002+A1+A11+A12+A2+A13
EN 60335-2-41:2003+A1:2004+A2:2010, EN 62233:2008
EN 55014-1:2006+A1:2009+A2:2011, EN 55014-2:1997+A1:2001+A2:2008,
EN 61000-3-2:2006+A1:2009+A2:2009, EN 61000-3-3:2008
Wiesbaden, 1st October 2017
ppa. Peter Neumüller
English 5
Solution
Check suction line and connections
for vacuum tightness
Air in the system must be let out
Impeller wheel must be cleaned
Pump needs to be cooled
Check electrical connections
Insert pump not so deep
Check hose connection systems
Change impeller wheel
Clean filter
Check pump for moisture damage
Unplug the pump / contact the
distributor
Advertisement
