Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Sun Microsystems 1500
Summary of Contents for Sun Microsystems 1500
- Page 1 Sun Blade™ 1500 Service, Diagnostics, and Troubleshooting Manual Sun Microsystems, Inc. 4150 Network Circle Santa Clara, CA 95054 U.S.A. 650-960-1300 Part No. 816-7564-10 April 2003, Revision A Send comments about this document to: docfeedback@sun.com...
-
Page 2: Removing Dimms
DIMM Location and Identification FIGURE 11-1 Depending upon the configuration of your workstation, you can either add or replace memory. In either case, the new DIMMs must meet the Sun workstation requirements. DIMM Configurations TABLE 11-1 Memory 512 MB memory 1GB memory 2GB memory When your workstation boots up, the OpenBoot PROM checks for compatible... -
Page 3: Identifying The Rear Fan
13.3.1 Identifying the Rear Fan The front and rear fans on the Sun Blade 1500 workstation are contained in green brackets. Both fans must be operating to adequately cool the components in a closed chassis. Both fans are connected to the motherboard with a cable that carries power and signal. -
Page 4: Removing The Smart Card Reader
See 3. Disconnect the interface cable from the motherboard. The cable is connected on the motherboard at SCR0. See 12-16 Sun Blade 1500 Service, Diagnostics, and Troubleshooting Manual • April 2003 Smart card reader Smart card reader cable... -
Page 5: Chapter 14 Replacing Internal Cables
14.2.1 Identifying the DVD-ROM Drive Interface Cable The DVD-ROM has separate power and interface cables. The power cable is a Y cable that connects to the motherboard at IDE PWR and the other ends to the hard drives and DVD-ROM drive. The interface cable connects the DVD-ROM drive to the motherboard at IDE SEC. - Page 6 3. Disconnect the IDE power cables from the upper hard drive HDD0. FIGURE 14-12 Connector IDE PWR Disconnecting the IDE Power Cable From the Hard Drive(s) FIGURE 14-12 4. If installed, disconnect the IDE power cable from the lower hard drive HDD1. FIGURE 14-12 5.
-
Page 7: Replacing The Hard Drive Interface Cable
The interface cable is an 80-conductor ribbon cable that is routed through the chassis. FIGURE 14-8 Hard Drive Interface Cable Connection FIGURE 14-8 14-10 Sun Blade 1500 Service, Diagnostics, and Troubleshooting Manual • April 2003 shows the hard drive interface cable connections. HDD0 HDD1 Hard drive interface cable... -
Page 8: See Figure
Guide rails Pressing the Catch on the Rear Fan Bracket FIGURE 11-3 4. Slide the duct up until it is flush with the edge of the rear fan bracket. FIGURE 11-4 Duct flush with bracket Sliding the Duct Up FIGURE 11-4 5. -
Page 9: Chapter 10 Preparing To Replace Components
Bezel Location and Identification FIGURE 10-9 3. Release the lower mounting tabs. Carefully move the lower pair of mounting tabs apart, and then push them forward slightly. See FIGURE 10-10 Releasing the Bezel Mounting Tabs FIGURE 10-10 As you do this, you should see the bottom of the bezel move slightly away from the chassis. - Page 10 Set the clip aside. If removing clips separately, repeat from Step a for the other clip. See FIGURE 11-16 Releasing the CPU Fan and Heatsink Assembly Clips FIGURE 11-16 11-16 Sun Blade 1500 Service, Diagnostics, and Troubleshooting Manual • April 2003 Locking ring Latch Center tab Clips (2) Clips (2)
-
Page 11: Identifying The Battery
Refer to: “Powering Off the Workstation” on page 10-4 “Removing the Access Panel” on page 10-12 “Positioning the Chassis” on page 10-16 11-22 Sun Blade 1500 Service, Diagnostics, and Troubleshooting Manual • April 2003 Battery clip Battery (BAT0) Value 3 VDC... - Page 12 Identifying the PCI Card Slots FIGURE 11-34 3. Swing out the PCI card support. Squeeze the inside tabs together and swing the PCI card support out. See FIGURE 11-35 11-36 Sun Blade 1500 Service, Diagnostics, and Troubleshooting Manual • April 2003...
- Page 13 Routing clip Power supply cables Removing Cables From the Routing Clips FIGURE 11-42 9. Disconnect the power and signal cables. Disconnect the following power and signal cables from the corresponding motherboard connectors and set them out of the way of the motherboard. See FIGURE 11-41 Power supply cables at connectors PS0, PS1, and PS2 IDE power at connector IDE PWR...
-
Page 14: Installing The Pci Card Support
Removing the PCI Card Support FIGURE 13-48 Note – Do not use the chassis cross brace as a handle. Proceed to “Installing the PCI Card Support” on page 13-45. Note – Do not operate the workstation without the PCI card support installed. 13.7.3 Installing the PCI Card Support 1. -
Page 15: Chapter 15 Finishing Component Replacement
Reconnecting the Keyboard, Mouse, Monitor, and Network Connections FIGURE 15-8 2. Reconnect any other external peripherals. 3. Power on those peripherals. Note – The monitor must be powered on before the system so that the monitor can communicate with the graphics accelerator when the system powers on. 4.