Related Manuals for GABOR TM-3255
Summary of Contents for GABOR TM-3255
- Page 1 TILTING TM-3255, TM-3770 TV MOUNT with Post-Installation Adjustment for 32 – 55 in. / 37 – 70 in. TVs User Manual...
- Page 2 Thank you for choosing Gabor. The Gabor TM-3255 and TM-3770 tilting wall mounts offer rugged and durable support for flatscreen monitors that weigh up to 176 pounds (80 kg). This TV mount’s low 2.1 in. (54 mm) profile assures that your screen will hang practically flush against the wall.
- Page 3 Welcome...
-
Page 4: Product Specifications
• 3/8 in. (10 mm) drill bit (for • Wall stud finder TM-3255: 32 – 55 in. (81.28 – 139.7 cm) drywall and concrete installation) TM-3770: 37 – 70 in. (94 – 177.8 cm) PRODUCT CONTENTS • Adjustment: -10°, +5° of tilt Supplied Parts &... - Page 5 Wall Mount Hex Key Bubble Level Wall Mount Hardware Hardware A ×4 D ×4 F ×4 I ×4 Brackets B ×4 E ×4 G ×8 J ×4 C ×4 H ×4 K ×4 Locking Bar Contents...
- Page 6 ATTACHING BRACKETS TO THE SCREEN Using spacers Determine whether screws Place one or any combination A, B, or C fit the threaded of spacers (G) or (H) between Two different sizes of holes on the back of your the screen and the bracket. spacers are included with screen.
- Page 7 1. Align the screw holes with the mounting holes on your screen. The brackets should be positioned with the small, round screw holes at the top of the screen. 2. Attach the brackets, using washers (F) and screws. Installation Instructions...
-
Page 8: Attach The Wall Plate To The Wall
ATTACH THE WALL PLATE TO THE WALL Wood Stud Installation 2. Place the wall mount over 4. Attach the wall mount your pencil marks. Use to the wall with screws 1. Use a stud finder to the included leveler to (I) and washers (K) until locate the studs in your make sure the wall mount... - Page 9 5. Check the horizontal orientation by placing the bubble level on the top edge of the wall mount. If the mount isn’t perfectly horizontal, gently tap the side that needs adjustment. 6. Once the wall mount is straight, tighten the screws until the mount secure.
- Page 10 Drywall and Concrete 3. Attach the wall mount to If the mount isn’t perfectly Wall Installation the wall with screws (I) horizontal, gently tap and washers (K) until the the side that needs 1. In the area where you wall mount is held in place, adjustment.
- Page 11 MOUNTING THE SCREEN TO THE WALL MOUNT Important! We recommend 1. Lift the screen up to the 2. Use the tilt tensions wall mount, and hang that two people perform knobs on both brackets the screen from the top this step. to adjust the tension on hooks of the brackets.
- Page 12 USING THE LOCKING BAR 1. For extra security, align 2. Insert a lock into the hole the locking bar with the at the end of the bottom hooks of the locking bar. brackets, and slide it in from the right side behind the screen.
- Page 13 POST-INSTALLATION ADJUSTMENT Adjustment screws are located at the top of each bracket. Once your screen is mounted on the wall mount, use the included bubble level to check the horizontal orientation of your screen. If necessary, use the included hex key to turn the adjustment screws until the bubble is between the two level lines.
-
Page 14: Safety Warnings
Gabor takes no responsibility for any wall studs or on a solid concrete abide by the mounting instructions product damage or personal injury wall to properly support the weight may void the product warranty. -
Page 15: Customer Support
CUSTOMER SUPPORT ONE-YEAR LIMITED WARRANTY: This GABOR product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year For more information or from the original purchase date or thirty (30) days after replacement, whichever occurs later. - Page 16 MADEBYGABOR WWW. .COM...