Advertisement
INSTALLATION INSTRUCTIONS
ADV-X HIGH SPEED METAL DOORS
MODELS 888 AND 889
www.wayne-dalton.com
This installation manual provides
the trained door technician
information required to install a
ADV-X High Speed Metal door.
READ COMPLETE INSTRUCTIONS
BEFORE INSTALLING DOOR.
Some installation tasks listed in
this document are found in other
documents.
Please refer to the appropriate
document(s) as directed;
827804 Installation Instructions
VFD for High Speed Metal Doors
(Included)
308577 Hilti Kwik Bolt Installation
found on Ribbon Connect
This manual is intended ONLY
for professional use by a trained
door systems technician. All
others please refer to the end
user manual provided to you.
827802-0001
Rev -
1
Advertisement
Related Manuals for Wayne-Dalton ADV-X 888
Summary of Contents for Wayne-Dalton ADV-X 888
- Page 1 INSTALLATION INSTRUCTIONS ADV-X HIGH SPEED METAL DOORS MODELS 888 AND 889 This installation manual provides the trained door technician information required to install a ADV-X High Speed Metal door. READ COMPLETE INSTRUCTIONS BEFORE INSTALLING DOOR. Some installation tasks listed in this document are found in other documents.
-
Page 2: Table Of Contents
TABLE OF CONTENTS SECTION CONTENTS PAGES SAFETY INFORMATION INSTALLATION 4-16 FIRST MANUAL DOOR OPERATION 17-18 ELECTRONICS FINAL INSTALLATION STEPS WARRANTY www.wayne-dalton.com 827802-0001 Rev -... -
Page 3: Safety Information
SECTION 1 - SAFETY INFORMATION OVERVIEW OF POTENTIAL HAZARDS O PO READ THIS SAFETY INFORMATION WARNING 1. Read manual and warnings carefully. High Speed Metal Doors doors are large, heavy objects that move with the help of electric motors. Since 2. -
Page 4: Installation
SECTION 2 - INSTALLATION UNPACKING COMPONENTS WARNING CAUTION Use designated lifting hole and appropriate lifting equipment to avoid Lift from below with forklift. Do not lift with the damage, serious injury, or death. shafts. This could cause damage or personal injury. CAUTION Team lift to avoid injury. - Page 5 SECTION 2 - INSTALLATION SITE PREPERATION NOTE: Check that the fl oor, jamb, and header are level, square, and plumb. If they are not, you will need to add shims as necessary. A laser lever is highly recomended for this job. NOTE: Mark the fl oor in three places to help align the guides that will be placed in the following step.
- Page 6 SECTION 2 - INSTALLATION GUIDE INSTALLATION WARNING Use designated lifting hole and appropriate lifting equipment to avoid damage, serious injury, or death. NOTE: Guide NOTE: Align guides with marks covers swing open on the fl oor. Check DIM H at three on hinges, or can be points.
- Page 7 SECTION 2 - INSTALLATION GUIDE INSTALLATION NOTE: Check DIM H at three points. Ensure everything is square, level, and plumb before and after anchoring. Extra time spent at this point of the installation may prevent time consuming rework. NOTE: When using the steel anchoring slots it may be necessary to temporarily remove the track for access.
- Page 8 SECTION 2 - INSTALLATION HEADER ASSEMBLY INSTALLATION ALLATION ALLATION WARNING Use appropriate lifting equipment to avoid serious injury, or death. www.wayne-dalton.com 827802-0001 Rev -...
- Page 9 SECTION 2 - INSTALLATION SIDE PLATE INSTALLATION NOTE: Only loosly install side plate bolts. You will need some movement in the side plate to complete the next step. CAUTION Team lift to avoid injury. www.wayne-dalton.com 827802-0001 Rev -...
- Page 10 SECTION 2 - INSTALLATION IDLER PULLY INSTALLATION NOTE: Check alignment of pulleys and tighten set screws in set collars and bearings to prevent excessive wear on the belts. www.wayne-dalton.com 827802-0001 Rev -...
- Page 11 SECTION 2 - INSTALLATION SIDE PLATE BRACKET INSTALLATION www.wayne-dalton.com 827802-0001 Rev -...
- Page 12 SECTION 2 - INSTALLATION BELT INSTALLATION NOTE: Counterweight belt is yellow. Drive belt is grey. NOTE: It is a good idea to check that the drive belts are equal in length. Unwind the drive belt on both sides and count the number of wraps to be sure before connecting to the curtain.
- Page 13 SECTION 2 - INSTALLATION MOTOR INSTALLATION CAUTION Team lift to avoid injury. www.wayne-dalton.com 827802-0001 Rev -...
- Page 14 SECTION 2 - INSTALLATION COUNTERWEIGHT INSTALLATION WARNING NOTE: The assembly of the front sliders may be easier if done after rasing the counterweight up off the spacers a little using the Use appropriate lifting equipment ratchet. to avoid serious injury, or death. www.wayne-dalton.com 827802-0001 Rev -...
- Page 15 SECTION 2 - INSTALLATION COUNTERWEIGHT INSTALLATION NOTE: Assemble belt clamp after the counterweight has been raised into the proper position using the ratchet. www.wayne-dalton.com 827802-0001 Rev -...
- Page 16 SECTION 2 - INSTALLATION FLIP SHIPPING BRACKET www.wayne-dalton.com 827802-0001 Rev -...
-
Page 17: First Manual Door Operation
SECTION 3 - FIRST MANUAL DOOR OPERATION CHECKLIST AND MANUAL DOOR LOWERING NOTE: Double check belts. Be NOTE: Tighten all set screws NOTE: Check and tighten all sure they are tight and properly in set collars and bearings. nuts and bolts. aligned. - Page 18 SECTION 3 - FIRST MANUAL DOOR OPERATION CHECK AND ADJUST CHECK AND ADJUST NOTE: After leveling the curtain install belt clamps on drive belts above ratchet, just like on the counterweight belts. NOTE: Check that the curtain is level using a laser level. If you do not have a laser you can use a tape measure on both sides to ensure level.
-
Page 19: Electronics
SECTION 4 - ELECTRONICS INSTALL ELECTONIC COMPONENTS INSTALL ELECTONIC COMPONENTS NOTE: Install the junction box near the motor using fasteners appropriate for your jamb material. NOTE: Install control panel at eye level on the motor side using fasteners appropriate for your jamb material. Mounting holes are located inside the panel. -
Page 20: Final Installation Steps
SECTION 5 - FINAL INSTALLATION STEPS INSTALL FINAL ITEMS INSTALL FINAL ITEMS NOTE: Install covers and hood (some non-standard items shown). If hood will be used it should be installed fi rst. NOTE: Apply safety labels NOTE: Close or reattach guide covers. www.wayne-dalton.com 827802-0001 Rev -... -
Page 21: Warranty
2018© Overhead Door Corporation www.wayne-dalton.com 827802-0001 Rev -...