1. Manuals
  2. Brands
  3. rtd Manuals
  4. Switch
  5. LAN35M 08 Series
  6. User manual

rtd LAN35M 08 Series User Manual

Including idan versions. gigabit ethernet managed switches
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
LAN35MH08HR-D, LAN35ME08HR-D,
LAN35MH08HR-RJ, LAN35ME08HR-RJ
Including IDAN versions
Gigabit Ethernet Managed Switches
User's Manual
BDM-610020135 Rev. C
RTD Embedded Technologies, Inc.
AS9100 and ISO 9001 Certified

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the LAN35M 08 Series and is the answer not in the manual?

Questions and answers

Related Manuals for rtd LAN35M 08 Series

Summary of Contents for rtd LAN35M 08 Series

  • Page 1 LAN35MH08HR-D, LAN35ME08HR-D, LAN35MH08HR-RJ, LAN35ME08HR-RJ Including IDAN versions Gigabit Ethernet Managed Switches User’s Manual BDM-610020135 Rev. C RTD Embedded Technologies, Inc. AS9100 and ISO 9001 Certified...
  • Page 2 RTD Embedded Technologies, Inc. 103 Innovation Boulevard State College, PA 16803 USA Telephone: 814-234-8087 Fax: 814-234-5218 www.rtd.com sales@rtd.com techsupport@rtd.com...

  • Page 3: Revision History

    Failure to follow the instructions found in this manual may result in damage to the product described in this manual, or other components of the system. The procedure set forth in this manual shall only be performed by persons qualified to service electronic equipment. Contents and specifications within this manual are given without warranty, and are subject to change without notice. RTD Embedded Technologies, Inc. shall not be liable for errors or omissions in this manual, or for any loss, damage, or injury in connection with the use of this manual.

  • Page 4: Table Of Contents

    IDAN IEEE1588 Time Tick (CN26, pin 23) 4.4.3 IDAN-LAN35Mx08HR-D Ethernet Ports IDAN-LAN35Mx08HR-D Connectors IDAN-LAN35Mx08HR-D LEDs 4.4.4 IDAN-LAN35Mx08HR-RJ Ethernet Ports IDAN-LAN35Mx08HR-RJ Connectors IDAN-LAN35Mx08HR-RJ LEDs Steps for Installing ..................................35 Functional Description Block Diagrams ..................................36 | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.
  • Page 5 Performing a Firmware Upgrade .............................. 59 6.18.1 Using the Web GUI 6.18.2 Using ICLI 6.18.3 Using USB Serial Console Troubleshooting Additional Information PC/104 Specifications ................................62 PCI and PCI Express Specification ............................62 | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.
  • Page 6 Figure 41: PuTTY session logging to facilitate automatic configuration backup ....................57 Figure 42: Configuration backup using TFTP via ICLI ............................57 Figure 43: Configuration backup using Web GUI ..............................57 Figure 44: Factory default configuration using Web GUI............................58 | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.
  • Page 7 Table 19: IDAN-LAN35Mx08HR-D, Rear Connector Pin Out..........................33 Table 20: RJ-45 Signal Descriptions ..................................34 Table 21: Link Status LEDs ....................................38 Table 22: Switch Status LED ....................................38 | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 8: Introduction

    DIL connectors or in IDAN frames with either RJ-45 or 37-pin “D” connectors. The LAN35Mx08 features the RTD StackNET® connector, which allows additional RTD Ethernet switches and routers to be stacked in a PCIe/104 system with direct board-to-board Ethernet connectivity. The LAN35MH08HR is intended to be the host of a StackNET® stack and features a PCI Express Gigabit Ethernet controller for connection to a PCIe/104 cpuModule.

  • Page 9: Board Features

    Intel i210 PCI Express Ethernet Controller for interface to host cpuModule Eight 1000/100/10 Mbps Ethernet ports One upward StackNET® port for stacking switch expansion Power connector for standalone applications or use with RTD’s PCIe/104 or PCI/104-Express power supplies. • LAN35ME08HR expansion switch...

  • Page 10: Idan Features

    PTIONS RTD’s line of PCIe/104 Gigabit Ethernet Switches are available with RJ-45 or 10-pin DIL connectors. The LAN35MH08HR “host” version may be used as a stand-alone device, and include a power connector, while the LAN35ME08HR “expansion” version must be used with a host. The LAN35MH08HR &...

  • Page 11: Table 1: Board Ordering Options

    XK-CM83 DIL connector to RJ-45 (includes one adapter cable) Cable kit for all LAN35Mx08HR boards to provide a Mini USB Type B XK-CM123 connection to the USB Serial Console | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 12: Idan Ordering Options

    The Intelligent Data Acquisition Node (IDAN®) building block can be used in just about any combination with other IDAN building blocks to create a simple but rugged 104™ stack. This module can also be incorporated in a custom-built RTD HiDAN® or HiDANplus® High Reliability Intelligent Data Acquisition Node.

  • Page 13: Specifications

    PCIe/104 Bus (CN1 and CN2) Differential Output Voltage DC Differential TX 95.2 116.9 Ω Impedance Differential Input 0.175 Voltage DC Differential RX 92.7 115.8 Ω Impedance Electrical Idle Detect Threshold | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.
  • Page 14 Output low voltage = 12 mA Output low voltage = 2 mA Input high voltage 1.85 Input low voltage -0.3 Input high current μA Input low current μA Input capacitance | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 15: Board Connections

    When removing it from the bag, hold the board at the edges, and do not touch the components or connectors. Handle the board in an antistatic environment, and use a grounded workbench for testing and handling of your hardware. Physical Characteristics STEP model is available upon request; contact RTD Tech Support for more information. • LAN35Mx08HR-D Weight: Approximately 91 g (0.20 lbs) – with heatsink •...

  • Page 16: Figure 2: Lan35Mh08Hr-D & Lan35Me08Hr-D Mechanical Drawing

    CN8 on underside (LAN35ME08HR only) CN23 on LAN35MH08HR only Figure 2: LAN35MH08HR-D & LAN35ME08HR-D Mechanical Drawing | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 17: Figure 3: Lan35Mh08Hr-Rj & Lan35Me08Hr-Rj Mechanical Drawing

    CN8 on underside (LAN35ME08HR only) CN23 on LAN35MH08HR only Figure 3: LAN35MH08HR-RJ & LAN35ME08HR-RJ Mechanical Drawing | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 18: Connectors And Leds

    Power (LAN35MH08HR only) 1x12, 0.1”, right angle FCI 65039-025LF CN24 Factory Use Only CN25 Factory Use Only CN26 External LED Signals, Reset 2x13, 2mm, vertical FCI 89947-726LF Button, Time Tick | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 19: Port 1-8, 10-Pin Dil Ethernet (-D Version)

    Receive - MDI_C+ Not Used MDI_C- Not Used MDI_A+ Transmit + MDI_A- Transmit - MDI_D+ Not Used MDI_D- Not Used Shield Ground Shield Ground Table 8: Ethernet DIL Signal Descriptions | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 20: Port 1-8, Rj-45 Twisted Pair Ethernet (-Rj Version)

    Interface (ICLI). CN19 is a USB “device” port, with an Exar XR21B1411IL16 USB UART device. It is intended to be connected to the USB port of a PC (RTD cpuModule, laptop, or desktop). The USB signals comply with the USB 2.0 specification (Full Speed, 12Mbit/sec).

  • Page 21: Cn23, Power Input (Lan35Mh08Hr Only)

    CN23 may be used to power just a single LAN35MH08HR, or it may be used to power a stack of multiple RTD StackNET boards (e.g. one LAN35MH08HR plus several LAN35ME08HR boards). Additional power input options are any of RTD’s...

  • Page 22: Cn26 External Led, Switch Reset Button And Time Tick Connector

    CN23! If two +5V power supplies conflict, all boards in the stack may be damaged or destroyed. If a stack powered by CN23 contains any boards other than an RTD StackNET product (not recommended), be sure the non-StackNET board(s) do not back feed +5V onto the bus before applying power.

  • Page 23: Cn1 (Top) & Cn2 (Bottom) Pcie/104 Bus Connectors

    StackNET connector). Table 13: Bus Connectors Connector Function Location Size and Pitch Mating Connector PCIe/104 Universal Bus 156-pin, 0.635mm Samtec ASP-186622-01 PCIe/104 Universal Bus Bottom 156-pin, 0.635mm Samtec ASP-129637-03 | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 24: Steps For Installing

    Refer to section 4.5 for details on the serial port connection. b. Configure the CEServices software via the ICLI (see the software configuration information later in this document for details). | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 25: Figure 12: Example 104™Stack

    Figure 12: Example 104™Stack | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 26: Idan Connections

    IDAN-LAN35Mx08HR-D Weight: Approximately 310 g (0.68 lbs) • Dimensions: 152 mm L x 130 mm W x 17 mm H (5.983 in L x 5.117 in W x 0.669 in H) Figure 13: IDAN-LAN35Mx08HR-D Dimensions | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 27: Idan-Lan35Mx08Hr-Rj

    Dimensions: 152 mm L x 130 mm W x 17 mm H (5.983 in L x 5.117 in W x 0.669 in H) Figure 14: IDAN-LAN35Mx08HR-RJ Dimensions Figure 15: IDAN-LAN35MH08HR-RJ Figure 16: IDAN-LAN35ME08HR-RJ | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 28: Connector Locations

    (CN26) LAN35ME08HR only Figure 17: IDAN-LAN35Mx08HR-D Front Panel Connectors USB Serial Console (CN19) Ports 5 – 8 StackNET Downward Connector (CN8) LAN35ME08HR only Figure 18: IDAN-LAN35Mx08HR-D Back Panel Connectors | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 29: Idan-Lan35Mx08Hr-Rj

    LAN35ME08HR only Figure 19: IDAN-LAN35Mx08HR-RJ Front Panel Connectors USB Serial Console (CN19) StackNET Downward Ports 5 – 8 Connector (CN8) With LEDs LAN35ME08HR only Figure 20: IDAN-LAN35Mx08HR-RJ Back Panel Connectors | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 30: Host Version Photos

    1658610-1 1658608-1 PORT 8 IEEE1588 Time Tick SMA Jack, Amphenol RF Amphenol RF SMA Plug CN26 (LVCMOS 2.5V, see 50 Ohm 132421 (Various) specifications) CN26 Reset Input Push button | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 31: Idan Usb Serial Console (Cn19)

    Programmable as input or output, 1 PPS, SMA Inner Sleeve IEEE1588 Time Tick 1Hz – 25MHz, LVCMOS 2.5V (3.3V tolerant) SMA Outer Barrel Ground Connection Table 17: IDAN Time Tick Pinout | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 32: Idan-Lan35Mx08Hr-D Ethernet Ports

    IDAN-LAN35Mx08HR-D Connectors The IDAN-LAN35MH08HR-D and IDAN-LAN35ME08HR-D both feature rugged 37-pin “D” connectors which each connect to four of the onboard Ethernet ports. These connectors can easily be adapted to RJ-45 connections by using RTD cable kit IDAN-XKCM48. LAN35MH08HR or IDAN...

  • Page 33: Idan-Lan35Mx08Hr-D Leds

    No Connect No Connect No Connect Table 19: IDAN-LAN35Mx08HR-D, Rear Connector Pin Out IDAN-LAN35Mx08HR-D LEDs Due to space limitations on the frame the IDAN-LAN35Mx08HR-D does not bring out any LEDs. | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 34: Idan-Lan35Mx08Hr-Rj Ethernet Ports

    Red Flashing – Error • HST or DWN – Host or StackNet down link Green – Link at 1Gbps, flash with activity Yellow – Link at 10/100Mbps, flash with activity | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 35: Steps For Installing

    Refer to section 4.5 for details on the serial port connection. Configure the CEServices software via the Command Line Interface (see the software configuration information later in this document for details). Figure 27: Example IDAN System | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 36: Functional Description

    The Figures below shows the functional block diagram of the LAN35MH08HR and LAN35ME08HR. The key features of the board are discussed in the following sections. Figure 28: LAN35MH08HR Block Diagram | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 37: Microsemi Vsc7428 Managed Ethernet Switch And Ceservices

    To use the I210, the appropriate networking drivers must be loaded in your Operating System. The I210 is a common Ethernet controller, so it is supported by many OSes. RTD distributes the Intel PRO Ethernet drivers for Windows 7 and later. For Linux, support is built into kernel 3.5 or later using the igb driver.

  • Page 38: Onboard Status Leds And External Led Pins

    PC. Modern versions of Windows include drivers for the USB UART. For older versions of Windows, a driver is provided by RTD. Once USB is connected and the drivers are loaded, the console interface will appear as a serial COM port in the PC’s operating system (e.g. COM5). The COM port number can vary depending on how ports were enumerated by the operating system, so it is difficult to predict.

  • Page 39: Usb Serial Console Typical Boot Messages

    Black text indicates user typed text. Text in enclosed in <> indicate a specific keyboard key such as the spacebar indicated by <Space> or the enter key indicated by <Enter>. Press ENTER to get started If you require support, please contact RTD Embedded Technologies, Inc. Username: admin<Enter>...

  • Page 40: Reset Behavior

    However, any network communication with the CPU board would be interrupted while the CPU reboots (including Intel I210 Ethernet controller on the LAN35MH08HR). A “cold” reset which interrupts power to the LAN35MHx08 (RSM reset, ACPI S3 standby, etc) will reset the VSC7428. | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 41: Ceservices Software Overview

    <Enter>. The default password is blank, so just press <Enter>. Press ENTER to get started If you require support, please contact RTD Embedded Technologies, Inc. Username: admin<Enter>...

  • Page 42: Listing Commands

    Once in configuration mode, the command prompt changes from HOSTNAME# to HOSTNAME(config)#. In the factory default configuration with no host name set, the prompt will simply be (config)#. configure terminal<Enter> (config)# ?<Enter> | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.
  • Page 43 Managed Switch Firmware package. When done configuring the switch, use exit to exit configuration mode. Multiple uses of exit will bring you to the exec level, or you can use end to bring you directly back to the exec level. | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 44: Saving The Configuration Changes

    RTD-SWITCH# show running-config<Enter> Building configuration... banner exec "TIP: If Backspace does not work, use Ctrl-H for Backspace." banner login "If you require support, please contact RTD Embedded Technologies, Inc." hostname RTD-SWITCH logging level notice username admin privilege 15 password none...
  • Page 45 SSH network connection -- more --, next page: Space, continue: g, quit: ^C <Space> line vty 5 exec-timeout 15 0 location SSH network connection line vty 6 exec-timeout 15 0 | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 46: Icli Configuration Command Negation

    Port 2 = GigabitEthernet 1/2 • Port 3 = GigabitEthernet 1/3 • Port 4 = GigabitEthernet 1/4 • Port 5 = GigabitEthernet 1/5 • Port 6 = GigabitEthernet 1/6 | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 47: Showing Interface Status With Icli

    Once in the interface configuration sub- mode, the command prompt changes from HOSTNAME(config)# to HOSTNAME(config-if)#. To switch back to “global” configuration mode, type exit. configure terminal<Enter> (config)# interface GigabitEthernet 1/1<Enter> | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.
  • Page 48 To set an IP address, one should create a VLAN interface and set an IP address there, then assign one or more physical interfaces to the newly- created VLAN. By default, all ports are part of VLAN 1, which already exists in factory default configuration. Refer to the following sections for details. | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 49: Common Configuration Task: Setting A Password With Icli

    (note the last line): show running-config<Enter> Building configuration... banner exec "TIP: If Backspace does not work, use Ctrl-H for Backspace." banner login "If you require support, please contact RTD Embedded Technologies, Inc." logging level notice username admin privilege 15 password encrypted TXVzdEJlQ2hhbmdlZA== The above commands demonstrate the most basic method of setting a password.

  • Page 50: Adding A Default Route Via Icli

    (8.8.8.8 and 8.8.4.4). DHCP lease time is 1 day. To be a DHCP server, the switch must be configured with a static IP address. In this case, we use the same static IP address as before (192.168.0.5). configure terminal<Enter> | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 51: Enabling Snmp Server

    Subnet Mask: 255.255.255.0 Default Gateway: 192.168.0.1 6.11 Enabling SNMP server SNMP is disabled by default by RTD Embedded Technologies. SNMP can be enabled by performing the following command via ICLI: configure terminal<Enter> (config)# snmp-server<Enter> (config)# exit<Enter> To verify that SNMP has been enabled, run the show snmp command and look at the first line of the configuration shown.

  • Page 52: Setting The Switch Clock With Ntp

    Login using the same username and password as you would for the USB Serial Console. Once you are logged in, the ICLI interface behaves identical to the USB Serial Console. Figure 31: Connecting with PuTTY (click Open to connect) | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 53: Figure 32: First Time Connection With Putty (Click Yes To Accept The Key)

    SSH access is enabled in the factory default configuration. It may be disabled with the configuration command no ip ssh. To re-enable it, use the configuration command ip ssh. | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 54: Network Management With Web Gui

    You will be prompted to login. Use the same username and password as you would for the USB Serial Console or SSH. The appearance of the login prompt may vary depending on your web browser. | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 55: Figure 36: Web Gui Login (Same User As Icli)

    Similar to ICLI, one must remember to save their configuration changes to the flash, or they will be lost when the switch is rebooted. Under the Web GUI, the configuration may be saved under Maintenance > Configuration > Save startup-config. | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 56: Backing Up The Switch Configuration

    PuTTY and other terminal emulators include a session logging feature which automatically saves the session contents to a text file. This allows for automatic backups of a configuration. Every time show running-config is run, it is automatically captured to the log, where it may be extracted later. | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 57: Downloading The Configuration Via Icli

    Under ICLI, the factory defaults may be loaded by deleting the startup configuration from the flash, and then rebooting CEServices. This may be done via either USB Serial Console, SSH, or Telnet. Once the startup configuration is deleted, a few errors may appear on the console | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 58: Loading Defaults Via Web Gui

    Informational: 1 : 12 Level Time & Message ---------- ------------- -------------- Informational 1970-01-01T00:00:01+00:00 SYS-BOOTING: Switch just made a cold boot. Notice 1970-01-01T00:00:02+00:00 LINK-UPDOWN: Interface Vlan 1, changed state to down | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 59: Performing A Firmware Upgrade

    Performing a Firmware Upgrade From time to time, RTD may offer firmware upgrades for the LAN35Mx08. These upgrades may be installed by the user. Running the latest available firmware is highly recommended. Running an older firmware version may have security implications.

  • Page 60: Using The Web Gui

    User-installed firmware upgrades will not affect the RedBoot boot loader. This is by design. The boot loader provides low level system recovery and troubleshooting. In general, the boot loader should not be altered unless you have been given special instructions from RTD Techsupport.

  • Page 61: Troubleshooting

    If problems persist, or you have questions about configuring this product, contact RTD Embedded Technologies via the following methods: Phone: +1-814-234-8087 E-Mail: techsupport@rtd.com Be sure to check the RTD web site (http://www.rtd.com) frequently for product updates, including newer versions of the board manual and application software. | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.

  • Page 62: Additional Information

    PCI and PCI Express Specification A copy of the latest PCI and PCI Express specifications can be found on the webpage for the PCI Special Interest Group: www.pcisig.com | www.rtd.com LAN35MH08HR & LAN35ME08HR User’s Manual RTD Embedded Technologies, Inc.
  • Page 63 During the one year warranty period, RTD Embedded Technologies will repair or replace, at its option, any defective products or parts at no additional charge, provided that the product is returned, shipping prepaid, to RTD Embedded Technologies. All replaced parts and products become the property of RTD Embedded Technologies.
  • Page 64 RTD Embedded Technologies, Inc. 103 Innovation Boulevard State College, PA 16803 USA Telephone: 814-234-8087 Fax: 814-234-5218 www.rtd.com sales@rtd.com techsupport@rtd.com Copyright 2019 by RTD Embedded Technologies, Inc. All rights reserved.

This manual is also suitable for:

Lan35mh08hr-dLan35mh08hr-rjLan35me08hr-rjLan35me08hr-d

Table of Contents