Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Stoelting Endura 131G
Summary of Contents for Stoelting Endura 131G
- Page 1 Endura/Futura 131G OWNER'S MANUAL Manual No. 513536-4 Feb. 2004, Rev. 0...
- Page 3 Need Parts or Service? We stock the parts you need. Our Technicians are factory trained and are certified in the Stoelting Technicare program. CALL Distributor: _________________________ Phone No.: Model No.: _______________________ Serial No.: _______________________ Purchase Date: ____________________ Start-Up Date:____________________ _________________________...
- Page 5 Owner's Manual For Endura and Futura 131G Stoelting Counter Model Gravity Freezer Soft Serve This manual provides basic information about the freezer. Instructions and suggestions are given covering its operation and care. The illustrations and specifications are not binding in detail. We reserve the right to make changes to the freezer without notice, and without incurrring any obligation to modify or pro- vide new parts for freezers built prior to date of change.
-
Page 7: Table Of Contents
SECTION 1 - SPECIFICATIONS ... 1.1 Description ... 1.2 Specifications ... SECTION 2 - INSTALLATION INSTRUCTIONS ... 2.1 Safety Precautions ... 2.2 Shipment and Transit ... 2.3 Freezer Installation ... 2.4 Floor Stand Installation ... 2.5 Installing Permanent Wiring ... SECTION 3 - INITIAL SET-UP AND OPERATION ... - Page 8 Fig. Description Model Endura/Futura 131G Freezer ... 1 Specifications ... 1 Warning Label Locations ... 3 Space and Ventilation Requirements ... 4 Installing Tray and Insert ... 4 Power Cord ... 4 Floor Stand ... 5 Power Cord Connection ... 5 Controls ...
-
Page 9: Section 1 - Specifications
SECTION 1 SPECIFICATIONS 1.1 DESCRIPTION The Stoelting Endura/Futura 131G counter freezer is grav- ity fed. The freezer is equipped with fully automatic controls to provide a uniform product. The freezer is designed to operate with almost any type of commercial soft serve or non-dairy mixes available, including ice milk, ice cream, yogurt, and frozen dietary desserts. - Page 10 MODEL ENDURA/FUTURA 131G COUNTER MODEL GRAVITY FREEZER Dimensions: Freezer: 22" (56 cm) wide x 28" (72 cm) deep x 34.75" (88 cm) high Crated: 28" (71 cm) wide x 35" (89 cm) deep x 38" (96 cm) high Weight: Freezer: 370 lbs. (168 kg) Crated: 450 lbs.
-
Page 11: Section 2 - Installation Instructions
ATTENTION: Customer Service Fig. 3. Warning Label Locations STOELTING, INC. 502 HWY 67 Kiel, Wisconsin 53042-1600 HEAT SENSITIVE THERMISTOR LOCATED UNDER THIS COVER. TEMPERATURE MUST NOT EXCEED 220°F NEAR... -
Page 12: Shipment And Transit
If concealed damaged and/or shortage is found later, advise the carrier within 10 days and request inspection. The customer must place claim for damages and/or shortages in shipment with the carrier. Stoelting, Inc. cannot make any claims against the carrier. 2.3 FREEZER INSTALLATION... -
Page 13: Floor Stand Installation
2.4 FLOOR STAND INSTALLATION To install the E/F131G on the floor stand, follow the steps outlined below. 1. Uncrate the floor stand and place in an upright posi tion. NOTE Detailed instructions are included with each floor stand. 2. Place a spirit level across the top of the stand to check for level condition, side to side and front to back. -
Page 15: Section 3 - Initial Set-Up And Operation
3.1 OPERATOR'S SAFETY PRECAUTIONS SAFE OPERATION IS NOT AN ACCIDENT; Observe these rules: A. Know the freezer. Read and understand the Operating Instructions. B. Notice all warning labels on the freezer. C. Wear proper clothing. Avoid loose fitting garments, and remove watches, rings or jewelry which could cause a serious accident. -
Page 16: Sanitizing
C. PUSH TO FREEZE SWITCH The PUSH TO FREEZE switch is a "snap" switch used to start the freezing cycle. During initial freeze down, the OFF-ON switch is placed in the ON position. Then the PUSH TO FREEZE switch is pressed until the drive motor and compressor come "ON". -
Page 17: Freeze Down And Operation
In general, sanitizing may be conducted as follows: A. Push the mix inlet regulator into hopper with air inlet (long) tube toward the front of the freezer. (Fig. 10). Figure 10. Mix Inlet Regulator B. Prepare 2 gallons (7.5 liters) of sanitizing solution following manufacturer’s instructions. -
Page 18: Mix Information
D. Fill hopper with approximately 3 gallons (11.4 liters) of prechilled (40°F or 4°C) mix. CAUTION DO NOT OVERFILL THE HOPPER. MIX LEVEL MUST NOT BE HIGHER THAN 2 INCHES (5 CM) FROM THE TOP OF THE AIR INLET TUBE ON THE MIX INLET REGULA- TOR. -
Page 19: Removing Mix From Freezer
3.6 REMOVING MIX FROM THE FREEZER To remove the mix from the freezer, refer to the following steps: A. Remove the mix inlet regulator from the hopper by pulling straight up (Fig.16). B. Place the OFF-ON rocker switch in the ON position and push the CLEAN switch to rotate the auger. -
Page 20: Removing Front Door
To disassemble the freezer, refer to the following steps: A. Remove the mix inlet regulator from the hopper by pulling straight up. B. Remove the front door by turning off the circular knobs and then pulling the front door off the studs (Fig.19). -
Page 21: Cleaning The Freezer Parts
Figure 23. Removing O-ring WARNING DO NOT USE ANY TYPE OF SHARP OBJECT TO REMOVE THE O-RINGS. 3.9 CLEANING THE FREEZER PARTS Place all loose parts in a pan or container and take to the wash sink for cleaning. To clean freezer parts refer to the following steps: A. -
Page 22: Routine Cleaning
CAUTION DO NOT PLACE THE MIX INLET REGULATOR INTO THE HOPPER BEFORE INSTALLING THE AUGER. E. Install the two plastic flights onto rear of the auger and insert part way into freezer barrel. F. Install the third plastic flight, push the auger into the freezer barrel and rotate slowly until the auger engages the drive socket. - Page 23 Once milkstone has formed, it is very difficult to remove. Without using the correct product and procedure, it is nearly impossible to remove a thick layer of milkstone. (NOTE: general-purpose cleaners DO NOT remove milkstone.) This can lead to high bacteria counts and a food safety dilemma.
- Page 24 With proper daily use of STERA-SHEEN or it’s equivalent, there is no need for the use of a DELIMER. DO NOT USE BLEACH · BLEACH HAS ABSOLUTELY NO CLEANING PROPERTIES. · BLEACH IS CORROSIVE. It can and will damage components of the machine causing premature wear and metal corrosion.
-
Page 25: Extended Storage
Figure 27. Condenser and Filter The condenser and condenser filter require periodic cleaning. To clean, refer to the following procedures. WARNING DISCONNECT FREEZER FROM ELECTRICAL SUPPLY SOURCE BEFORE SERVICING. 1. Remove the Phillips head screw from the bottom of the right side panel, and then slide the panels down and out. -
Page 27: Section 4 - Troubleshooting
i t c l l i . f f t l e r i f i a f r u l . t f u l l n i l . r i i l i r i f r i f i a f r u l a t l... - Page 28 t e l l a i y t i t l e t e l t e l t e l l l i F ° ° 7 t a l t e l t a l i a f r u l .
-
Page 29: Error Code System
CODE *Refer to Page 19 for Troubleshooting. If the Clean switch is operated three times within 10 seconds, this will cause the Push-To-Freeze light to flash and the clean function will be disabled for 10 minutes. The power switch must remain on or the 10 minute timer will not time out. -
Page 31: Section 5 - Replacement Parts
5.1 HOW TO ORDER PARTS To assure receipt of the proper replacement parts, supply your dealer or distributor with the following information: A. Model number of equipment. Part Number Description 208135 Brush, Nylon: 16" x 4", Wooden Handle 208380 Brush, Nylon: 14" x 1/4", Wire Handle 208401 Brush, Nylon: 10"... -
Page 32: Spigot, Front Door And Auger Assembly
Figure 29. Spigot, Front Door and Auger Assembly Item No. Part No. Description 2177428 Front Door Only 2177072 1.5" Spigot Extension 2177073 2.5" Spigot Extension 2177074 3" Spigot Extension 624677 Castle Top O-Ring 3158086 Center Spigot 3159696 Outside Spigot 625133 O-ring Front Door 624598 O-ring Outside Spigot... - Page 33 Stoelting, LLC warrants to the first user (the “Buyer”) that the freezer cylinders, hoppers, compressors, drive motors, speed reducers, auger and auger flights of Stoelting soft serve / shake freezers will be free from defects in materials and workmanship under normal use and proper maintenance appearing within five (5) years, and that all other...