Ip Routing; Routing With Vlan Interfaces; Routing Table And Routes - ABB EDS500 Series Function Manual

IP Routing

{ i n v e r s e - m o n i t o r | m o n i t o r } ] >
< c l e a r s y s t e m s n m p t r a p - s o u r c e v l a n [ { 1 - 4 0 9 4 } ] >
< s e t s y s t e m s n t p s o u r c e v l a n { 1 - 4 0 9 4 } [ d e p e n d e n c y { i n v e r s e -
m o n i t o r | m o n i t o r } ] >
< c l e a r s y s t e m s n t p s o u r c e v l a n [ { 1 - 4 0 9 4 } ] >
< s e t s y s t e m s y s l o g s o u r c e v l a n { 1 - 4 0 9 4 } [ d e p e n d e n c y
{ i n v e r s e - m o n i t o r | m o n i t o r } ] >
< c l e a r s y s t e m s y s l o g s o u r c e v l a n [ { 1 - 4 0 9 4 } ] >
2.31 IP Routing
EDS500 can be operated as IP router.
EDS500 devices support static and dynamic routing.
2.31.1

Routing with VLAN Interfaces

VLAN IP addresses have to be configured to use routing, refer to Chapter 2.9.3, "Configuration
of VLAN IP Addresses".
Routing has to be activated for all VLAN interfaces that participate in routing. Routing takes
place only between those VLANs that have enabled the routing property (<set interface
vlan {...} [no] routing>). There is no routing to or from VLAN interfaces that do not have this
property. These can only be reached in their own VLAN.
Display of IP address overview
< s h o w i n t e r f a c e i p - a d d r e s s >
I n t e r f a c e S u m m a r y :
I n t e r f a c e
v l a n 1 0
v l a n 2 0
Commands to configure routing with VLAN interfaces
< s e t i n t e r f a c e v l a n { 1 - 4 0 9 4 } r o u t i n g >
< s e t i n t e r f a c e v l a n { 1 - 4 0 9 4 } n o r o u t i n g >
< s e t i n t e r f a c e v l a n { 1 - 4 0 9 4 } i p - a d d r e s s { { I P a d d r e s s } [ { I P
a d d r e s s r a n g e e n d } ] { s u b n e t m a s k } } | { u n n u m b e r e d v l a n { v l a n -
i d } } >
< c l e a r i n t e r f a c e v l a n { 1 - 4 0 9 6 } i p - a d d r e s s [ { I P a d d r e s s } ] >
< s h o w i n t e r f a c e i p - a d d r e s s >
2.31.2

Routing Table and Routes

The routing table of the system can be displayed to show the current state of the IP routing.
The routing table shows the following:
• entries for static routing,
• entries for dynamic routing that are added via the routing protocol,
• local default gateways, if present.
Display of routing table
< s h o w i p r o u t e >
104
I P A d d r e s s I P G a t e w a y
1 0 . 0 . 0 . 1 1 / 8 -
2 0 . 0 . 0 . 1 0 / 2 9 -
A d m i n S t a t e L i n k S t a t e
u p u p
u p d o w n
1KGT151021 V000 1
Functions