Upright X26 Operator's Manual
  1. Manuals
  2. Brands
  3. Upright Manuals
  4. Scissor Lifts
  5. X26 Ultra Narrow
  6. Operator's manual

Upright X26 Operator's Manual

Hide thumbs Also See for X26:
Table of Contents

Advertisement

Quick Links

See also: Service Manual , Operator's Manual
WARNING
The X32 Machine has been re-assessed to ensure
compliance to the Machinery Directive (2006/42/EC).
The Machine rating has been changed from:
Windspeed rating of 12.5 m/s (Beaufort 6)
To
Windspeed rating of 7 m/s (Beaufort 4)
Please attach to the front cover of
your X32 manual
510329-000

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the X26 and is the answer not in the manual?

Questions and answers

Related Manuals for Upright X26

Summary of Contents for Upright X26

  • Page 1 WARNING The X32 Machine has been re-assessed to ensure compliance to the Machinery Directive (2006/42/EC). The Machine rating has been changed from: Windspeed rating of 12.5 m/s (Beaufort 6) Windspeed rating of 7 m/s (Beaufort 4) Please attach to the front cover of your X32 manual 510329-000...
  • Page 3 X32 Serial Numbers 50322 – Current NGLISH When contacting Upright for service or parts information, be sure to include the MODEL and SERIAL NUMBERS from the equipment nameplate. Should the nameplate be missing, the SERIAL NUMBER is also stamped on top of the chassis above the front axle pivot.
  • Page 5 NEVER charge batteries near sparks or open flame. Charging batteries emit explosive hydrogen gas. Modifications to the aerial work platform are prohibited or permissible only at the approval by UpRight. AFTER USE, secure the work platform from unauthorized use by turning both keyswitches off and removing key.

  • Page 6: Table Of Contents

    Lower the Guardrails, X26........

  • Page 7: Introduction

    Introduction 504165-002 NTRODUCTION This manual covers operation of the X 26-32 Self-Propelled Work Platforms. This manual must be stored on the machine at all times. ENERAL ESCRIPTION Figure 1: X 26-32 W A R N I N G DO NOT use the maintenance platform without guardrails properly assembled and in place 1.

  • Page 8: Special Limitations

    504165-002 Special Limitations PECIAL IMITATIONS Travel with the platform raised is limited to creep speed range. Elevating the Work Platform is limited to firm, level surfaces only. D A N G E R The elevating function shall ONLY be used when the work platform is level and on a firm surface. The work platform is NOT intended to be driven over uneven, rough, or soft terrain.

  • Page 9: Controls And Indicators

    Controls and Indicators 504165-002 ONTROLS AND NDICATORS Figure 2: Controls and Indicators Platform Controls 1 Drive Selectors 2. Horn Button 3. Lift/Lower Button 4. Emergency Stop Button 5. Display 6. Joystick Chassis Controls 1. Keyswitch 2. Enable Button 3. Toggle Switch (Up & Down) 4.

  • Page 10: Pre-Operation Safety Inspection

    504165-002 Pre-Operation Safety Inspection PERATION AFETY NSPECTION NOTE: Carefully read, understand and follow all safety rules, operating instructions, labels and National Safety Instructions/Requirements. Perform the following steps each day before use. 1. Open modules and inspect for damage, fluid leaks or missing parts. Figure 3: Hydraulic Tank 2.

  • Page 11: System Function Inspection

    System Function Inspection 504165-002 YSTEM UNCTION NSPECTION Refer to Figure 2 for the locations of various controls and indicators. W A R N I N G STAND CLEAR of the work platform while performing the following checks. Before operating the work platform, survey the work area for surface hazards such as holes, drop-offs, bumps and debris.

  • Page 12: Operation

    504165-002 PERATION Before operating the work platform, ensure that the Pre-Operation Safety Inspection has been completed and that any deficiencies have been corrected. Never operate a damaged or malfunctioning machine. The operator must be thoroughly trained on this machine. L A T F O R M X T E N S I O N Figure 4: Platform Extension 1.

  • Page 13: Travel With The Platform Elevated

    Stand clear of the elevating assembly while operating Emergency Lowering Knob the Emergency Lowering Valve Knob. X 26 The Emergency Lowering Valve for the X26 is located at the rear of the machine, above the charger. 1. Open the Emergency Lowering Valve by pulling and holding the knob.

  • Page 14: Lower The Guardrails, X26

    O W E R T H E U A R D R A I L S This procedure applies only to the X26 model for the purpose of passing through a standard double door- way. Guardrails must be returned to proper position before using the machine.

  • Page 15: Towing Or Winching

    Towing or Winching 504165-002 OWING OR INCHING Perform the following only when the machine will not operate under its own power and it is necessary to move the machine or when winching onto a transport vehicle (see “Transporting the Work Platform” on page 11).

  • Page 16: Lifting By Crane

    504165-002 Transporting the Work Platform Figure 6: Secure Crane Straps I F T I N G R A N E 1. Secure straps to chassis tie down/lifting lugs only. 2. Place the platform onto the transport vehicle in transport position. 3.

  • Page 17: Maintenance

    1. Using the Chassis Controls, gradually elevate the platform until the Scissor Brace is clear. 2. X26 – Rotate the Scissor Brace outward and upward over its mounting point until it rests in the stowed position. 3. X32 – Rotate the Scissor Brace clockwise until the locking pin engages.

  • Page 18: Battery Maintenance

    Always wear safety glasses when working near batteries. Battery fluid is highly corrosive. Thoroughly rinse away any spilled fluid with clean water. Always replace batteries with UpRight batteries or manufacturer approved replacements weighing 26,3 kg (58 lbs.) each. • Check the battery fluid level daily, especially if the work platform is being used in a warm, dry climate.

  • Page 19: Inspection And Maintenance Schedule

    Inspection and Maintenance Schedule 504165-002 NSPECTION AND AINTENANCE CHEDULE The Complete Inspection consists of periodic visual and operational checks, along with periodic minor adjustments that assure proper performance. Daily inspection will prevent abnormal wear and prolong the life of all systems. The inspection and maintenance schedule should be performed at the specified inter- vals.
  • Page 20 504165-002 Daily Preventative Maintenance Checklist OTES Page 16 Operation Manual...
  • Page 21 Decals 504165-002 ECALS These labels shall be present and in good condition before operating the work platform. Be sure to read, understand and follow these labels when operating the work platform. Operation Manual Page 17...
  • Page 22 504165-002 Decals ECALS Page 18 Operation Manual...

  • Page 23: Specifications

    Specifications 504165-002 PECIFICATIONS ITEM 1,17 m x 2,21 m 1.17 m x 2.21 m Platform Size w/ Extension [44,25 pulg. x 87 pulg.] [44 in. x 87 in.] Max. Platform Capacity Standard 454 kg [1000 lb] 340 kg [750 lbs.] on Extension 113 kg [250 lb] 113 kg [250 lbs.]...
  • Page 24 504165-002 Specifications Page 20 Operation Manual...
  • Page 26 Local Distributor: Lokaler Vertiebshändler: Distributeur local: El Distribuidor local: Il Distributore locale: Europe TEL: +1 (559) 443 6600 TEL: +44 (0) 845 1550 058 FAX: +1 (559) 268 2433 FAX: +44 (0) 195 2299 948 www.upright.com PN - 504165-002...

This manual is also suitable for:

X32X26-32

Table of Contents