Crestron INET-IOEX-IRCOM Quick Start

INET-IOEX-IRCOM
infiNET EX® Wireless IR/RS-232 Control Module
The Crestron® INET-IOEX-IRCOM control module provides an IR and
RS-232 control interface for video displays, AV components, small
appliances, and other equipment. The control module includes two
discrete IR ports and one bidirectional RS-232 port.
The control module communicates with a Crestron 3-Series® control
system via the infiNET EX® wireless network, allowing for control
and monitoring of remote devices without running wires or installing
conduit.
NOTE: The INET-IOEX-IRCOM is compatible only with Crestron
3-Series control systems.
Check the Box
Item
INET-IOEX-IRCOM
Connector, 2-Pin (P/N 2003574)
Connector, 3-Pin (P/N 2003575)
IR Emitter, with Terminal Block Connector, IRP2
(P/N 4500152)
Power Pack, 5 Vdc, 1.2 A, 100-240 Vac, Flying Leads
(P/N 2045867)
Install the Device
The INET-IOEX-IRCOM may be mounted onto any flat surface using
three mounting screws (not included).
NOTE: For best results, install the device in an location where it will
not receive interference from nearby RF sources, obstructions, and
metal surfaces.
INET-IOEX-IRCOM Mounting
screws (3)
Connect the Device
Make the necessary connections as called out in the following
illustration.
NOTE: The included IR emitters may be used to provide a one-way IR
control interface to an IR-controllable device. For more information,
refer to the IRP2 Installation Guide (Doc. 8186) at
www.crestron.com/manuals.
Qty
1
S/G (1–2):
To IR devices
1
(via included
IR emitters)
1
2
Connect to an infiNET EX Network
1
The INET-IOEX-IRCOM must be acquired by an infiNET EX wireless
gateway or by a control system with a built-in infiNET EX gateway
(both not included) before it may be used with a 3-Series control
system.
Use the procedures below to join or leave an infiNET EX network and
to verify communications between the device and the control system.
NOTE: The INET-IOEX-IRCOM may be acquired only by one network.
Join the infiNET EX Network
1. Enter Acquire mode using one of the following methods:
• Press the ACQUIRE button on the infiNET EX gateway.
•
Enter Acquire mode from Crestron Toolbox™ software. For
more information, refer to the Crestron Toolbox help file.
NOTE: In an environment where there are multiple gateways
installed, place only one gateway in Acquire mode at a time.
2. Press the SETUP button three times, and then press and hold
the SETUP button (press-press-press-press+hold) until the
LED on the device flashes once. This process may take up to ten
seconds to complete.
NOTE: If the INET-IOEX-IRCOM was previously acquired to
another gateway, instead press the SETUP button three
times, and then press and hold the button (press-press-press-
press+hold) for over ten seconds.
3. Release the SETUP button to start the acquire process. The LED
flashes slowly to show that the device is actively scanning the
infiNET EX network.
4. Confirm the status of the acquire process:
• If the INET-IOEX-IRCOM is acquired by the infiNET EX
network, the LED lights for five seconds.
•
If the INET-IOEX-IRCOM is not acquired by the infiNET EX
network, The LED flashes rapidly for several seconds. Press
the SETUP button to cancel the acquire process. Ensure the
gateway is in Acquire mode and that the INET-IOEX-IRCOM
is in range before attempting the acquire process again.
5. After the process is complete, remove the gateway from Acquire
mode as described by its documentation.
G/TX/RX: PWR:
To any From included
RS-232 5 Vdc, 1.2 A
device power pack