Marquis Spas DESTINY Owner's Manual page 38

SPIRIT™
# Component Identification
1 HK™8 Jets
2 HK™12 Jets
3 HK™16 Jets
4 HK™40 Jets
5 Bather's Control Panel
6 Filter Canisters
7 Suction Fitting
8 Ozone-ready Injector Fitting
9 Light
10 Neck Jet Valve
11 Jet Selector
12 Floor Drain
13 Waterfall Feature*
14 Waterfall Valve*
15 Spa Frog® Sanitation*
16 Spa Frog® Fitting*
17 Power Supply
Physical Specifications
Dimensions/mm
Height/mm
Interior Depth/mm
Corner Radius/mm
Seating Capacity/Positions
Weight Dry/Kgs.
Weight Full/Kgs.
Water Capacity/Litres
Total Therapy Jets
*Items are optional. Check with dealer for availability.
**HK™8 jets operate in every zone.
M A R Q U I S
Quantity
2
12
1
4
1
2
1
1
1
1
1
1
1
1
1
1
1
Size
2134 x 1524
749
711
432
3/4
186
810
623
19
®
S P A S
SPA CONTROL OPERATION
All spa models
PUMP PRIMING (Pr)
Pump priming feature begins at start-up. When your spa is energized, the LCD
window displays a "Pr" message. This mode lasts approximately four to five
minutes, if not exited manually by pressing the TEMP pad.
UNDERWATER AND ENTRYWAY LIGHTS
Press the LIGHT pad on bather's panel or remote control (option) to turn the
underwater and Entryway lights on and off. The low-voltage system produces a
night light for evening use and makes entering and exiting the spa safer. After
being on for 60 minutes, the lights automatically turn off.
AQUA AMBIANCE™ /CONSTELLATION™
Use LIGHT pad. Step one: turn on light. Step two: turn off and then on within 2-3
seconds. Repeat for all options.
NOTE: LED lights and non-LED lights do not qualify for labor coverage. These
parts can be purchased or exchanged under warranty at your authorized
Marquis Spas® dealer.
WATERFALL FEATURE
The Waterfall feature and Convenience Center attaches securely to the dual
Vortex skimmer tops. The water flow is controlled by an independent valve.
NOTE: Don't remove the waterfall top while the pumps are running.
JETS
Use the JETS pad on the bather panel or remote control. First press of the JETS
pad activates pump on low-speed (and starts soak timer). Second press of the
JETS pad activates pump on high-speed. Third press of the JETS pad turns jets
off for all-quiet mode. Fourth press of the JETS pad turns pump back to low-
speed. If the pump is already on low (heating, filter cycle), then the first press
starts the soak timer. After running on low- or high-speed for 15 minutes, the
pump automatically turns off (unless in heating or filtering cycle).
SOAK TIMER
The soak timer starts the first time you press a JETS pad. The LCD window
displays the elapsed time (1-30 minutes) for 55 seconds, then switches to the
current water temperature for five seconds, then back to the timer. It continues
to alternate for the entire 30 minutes. The timer runs for 30 minutes regardless
of other functions in use (jets, temperature, or light). You can manually cancel
the timer by pressing the TEMP+- pad and then the LIGHT pad.
REMOTE CONTROL (OPTION)
NOTE: During times of inactivity, wireless remotes should always be stored in
the cup holder on the lip of the spa or removed from the spa. By storing the
wireless remote out of water, it will be less susceptible to water intrusion, a
situation that can occur after extended water exposure. More often, water
intrusion occurs when spa owners attempt to replace the batteries in their
remote and then do not properly reseal the remote. Battery replacement should
only be performed by spa care professionals. Batteries and water intrusion into
remote controls is not covered under the warranty. Remote controls do not
qualify for labor coverage. These parts can be purchased or exchanged under
warranty at your authorized Marquis Spas® dealer.
O W N E R ' S M A N U A L
12