Advertisement
Quick Links
Axis IP Camera Settings
1.
Introduction – NavNet TZtouch/2 with Axis
2.
Overview
2.1.
Summary – Setup Procedure
2.2.
Latest Axis Cameras Compatible
with H.264 Format
2.3.
Tested Axis Video Servers at FEC
3.
Setting up a PC
4.
Setting up Axis IP Camera
4.1.
Setting up IP Address of Axis IP
Camera
4.2.
Configuring Axis IP Camera
5.
Setting up Axis Video Server
5.1.
Setting up IP Address of Axis Video
Server
5.2.
Configuring Axis Video Server
6.
Showing Camera Images
6.1.
Checking Axis IP Camera(s) in
Menu
6.2.
Checking Axis Video Server(s) in
Menu
7.
Tips – 4 x IP Cameras + 2 x Video Servers
Advertisement
Related Manuals for Navnet TZtouch
Summary of Contents for Navnet TZtouch
- Page 1 Axis IP Camera Settings Introduction – NavNet TZtouch/2 with Axis Setting up Axis Video Server Overview 5.1. Setting up IP Address of Axis Video 2.1. Summary – Setup Procedure Server 2.2. Latest Axis Cameras Compatible 5.2. Configuring Axis Video Server with H.264 Format Showing Camera Images 2.3.
- Page 2 1. Introduction – NavNet TZtouch/2 with Axis NavNet TZtouch (TZT9/14/BB) and NavNet TZtouch2 (TZTL12F/15F) v5.02 are compatible with IP cameras from Axis Communications AB in both MPEG-4 and H.264 formats. Native H.264 formatted images occupy a great amount of bandwidth. In addition to conventional settings such as IP address, ensure to set the resolution to "800x600 (4:3)"...
- Page 3 2.3. Tested Axis Video Servers at FEC At Furuno USA, the following Axis video servers were used for tests. M7014 http://www.axis.com/products/cam_m7014/index.htm Analog Input: Four (4) channels Ethernet Output: One (1) channel P7214 http://www.axis.com/products/cam_p7214/index.htm Analog Input: Four (4) channels Ethernet Output: One (1) channel...
- Page 4 3. Setting up a PC This section describes how to assign a dedicated IP address to a PC. (1) Access [Start] – [Control Panel]. (2) Open [Network and Sharing Center]. (3) Open [Change adapter settings]. (4) Right click on [Local Area Connection] and select [Properties].
- Page 5 (5) Select [Internet Protocol Version 4 (TCP/IPv4)] and click on [Properties]. (6) Fill the IP fields as shown below. IP address: 172.31.3.50 Subnet mask: 255.255.0.0 (7) Click on [OK] to confirm and close two windows on Step 6 and 5. Note: It takes up to 20 seconds for the new IP to be recognized.
- Page 6 4.1. Setting up IP Address of Axis IP Camera To work in the NavNet TZtouch/2 system, the Axis IP cameras need to be set up with specific IP Addresses. Up to four (4) IP cameras can be connected in the network.
- Page 7 (4) Install the AXIS IP Utility program on your PC. (5) Double-click on [AXIS IP Utility] to open the program. The following window will open, showing the detected cameras in the network. Note: If you use the same camera models in multiple locations, MAKE SURE to WRITE DOWN the IP camera’s serial numbers, which can be found on the back of the camera, with the intended location to help correctly assign the IP camera’s name.
- Page 8 It will take a while before the process is finished. (8) Check that the IP address is changed. (9) Repeat the process with the other camera(s). (10) After the IP address is changed, restart the camera (power OFF/ON). 4.2. Configuring Axis IP Camera Axis IP cameras need to be configured using a Web browser.
- Page 9 (3) You will be asked for an ID and password. Enter the following ID and password and click on [OK]. : root Password : pass Note: When the webpage loads, pay attention to the top of the page to authorize the installation of the ActiveX®. Click on the yellow bar and choose [Install ActiveX].
- Page 10 (7) In [Basic Setup] – [4 Video Stream] – [Image] tab, set [Resolution] to less than "800x600 (4:3)" and [Compression] to [30] and click on [Save]. In this example, [640x480 (4:3)] is selected as Resolution because this is the maximum resolution supported by the M1011. Tips: As another example with the Axis M5013, supporting a higher resolution than the M1011, set [Resolution] to [800x600 (4:3)].
- Page 11 Note: It is recommended to zoom in on the image (Tele) to have a better “Home” preset. When the view is correctly set up, type “Home” for the Current position and select [Use current position as Home]. Click on [Add] to validate. If you do not need the camera to return to the “Home”...
- Page 12 5.1. Setting up IP Address of Axis Video Server To work in the NavNet TZtouch/2 system, the Axis video servers need to be set up with specific IP Addresses. Up to two (2) video servers can be connected on a network.
- Page 13 (10) After the IP address is changed, restart the video server (power OFF/ON). 5.2. Configuring Axis Video Server Axis video servers need to be configured using a Web browser like IP cameras. (1) Enter the IP address of the video server. In this example, [http://172.31.200.7] is entered. (2) The camera configuration page will open.
- Page 14 (4) After entering the ID and password, the Setup page will open. (5) In [Basic Setup] – [1 Users], select [Enable anonymous viewer login] and click on [Save]. (6) In [Basic Setup] – [3 Date & Time], select [Synchronize with computer time] and click on [Save]. (7) In [Basic Setup] –...
- Page 15 (8) In [Basic Setup] – [4 Video Stream] – [Video 1] to [Video 4] and [Quad Stream] – [H.264] tab, set as follows. 6. Showing Camera Images This section describes how to show camera images on the TZT9/14/BB and TZTL12F/15F. 6.1.
- Page 16 6.2. Checking Axis Video Server(s) in Menu (1) After the interconnection and setup of video servers finish, check that they are detected in the TZT9/14/BB and TZTL12F/15F network, accessing [Menu]/[Settings] – [Camera] – [Axis Quad Server] and [Second Axis Quad Server].
- Page 17 7. Tips – 4 x IP Cameras + 2 x Video Servers As Axis IP camera and video server sources, a maximum of four (4) sets of IP cameras and two (2) sets of video servers are available in one network. In this example, the following items are configured and networked with the TZT14. Items Models IP Addresses...
- Page 18 Notes: In one TZT9/14/BB, a maximum of two (2) screens can be allocated to the Camera page in the 3-split screen mode. Select one of these sources in each screen. Among multiple IP camera inputs, the TZTL12F/15F can assign only one camera screen per display. Two (2) camera images CANNOT be simultaneously shown on both quarter (1/4) screens as shown at right.