Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Navnet Manuals
  4. Car Navigation system
  5. TZtouch
  6. Installation checklist

Navnet TZtouch Installation Checklist

Hide thumbs Also See for TZtouch:

Advertisement

Quick Links

Download this manual
Pg. 2 – 4: NavNet TZtouch MFD Network Installation (w/o: NN3D)
Pg. 5:
MIXED NavNet TZtouch MFD and NavNet 3D MFD
Network Installation
Pg. 6:
DFF1 Dip Switch Settings
Pg. 7:
DFF3 Dip Switch Settings
Pg. 8:
PSU-012 / 013 – Jumper Locations for TZT9 / 14
Installations
Pg. 9:
How to update a DRS using a TZT9 or TZT14 MFD
display

Advertisement

loading

Related Manuals for Navnet TZtouch

Summary of Contents for Navnet TZtouch

  • Page 1 Pg. 2 – 4: NavNet TZtouch MFD Network Installation (w/o: NN3D) Pg. 5: MIXED NavNet TZtouch MFD and NavNet 3D MFD Network Installation Pg. 6: DFF1 Dip Switch Settings Pg. 7: DFF3 Dip Switch Settings Pg. 8: PSU-012 / 013 – Jumper Locations for TZT9 / 14 Installations Pg.
  • Page 2 “J7”. (This allows the PSU to start without a power synchronization signal). Note: A sticker Optional jumper for TZtouch included” is placed on all “ PSU units that include a jumper for “J7” in the packaging! You MUST still open the PSU and insert it. If you are utilizing an existing PSU, just order the jumper (part # 001-183-760-00) and insert it on J7 to make the PSU compatible with a NNTZtouch network.
  • Page 3 touch Once the NNTZ MFDs have started, press the “Home” button and touch “Menu” on each MFD to confirm that you see both a radar and sounder menu (assuming you have both a sounder and radar connected to the Ethernet Network). o If you are missing the Sounder menu, make sure that the DFF1/DFF3 sounder DIP switch settings are correct and that you see good traffic (blinking green light) on the Ethernet port.
  • Page 4 However, only one MFD will actually output data on the NMEA2000 bus (the one that was first powered ON). If that MFD is turned OFF or fails, another TZtouch MFD will automatically replace it and start outputting the same PGNs onto the NMEA2000 backbone.
  • Page 5 (We strongly Make sure the NN3D network is fully operational. recommend that you update any existing NN3D MFDs with the latest software before integrating a new TZtouch MFD into a NN3D Network) touch Connect the NNTZ to the NN3D Ethernet network.
  • Page 6 DFF1 to an original NavNet, NavNet VX2 or TZtouch only system, you need to change the MODE switches as shown below. If the DFF1 will be installed in a system comprised of a NavNet 3D MFD8, MFD12 or MFDBB AND either of the TZtouch displays, the DIP Switches must remain in the DEFAULT (NavNet 3D) position shown below.
  • Page 7 DFF3 to an original NavNet, NavNet VX2 or TZtouch only system, you need to change the MODE switches as shown below. If the DFF3 will be installed in a mixed system comprised of a NavNet 3D (MFD8, MFD12 or MFDBB) AND TZtouch, the DIP Switches must remain in the DEFAULT (NavNet 3D) position shown below.

  • Page 9: Update Procedure

    How to Update a DRS radar sensor using a TZT9 or TZT14 MFD display Create the program update SD-Card A blank 128MB or larger SD Card is needed for the update. Furuno highly recommends using “SanDisk” SD-Cards. a. Download the ZIP file located under any DRS radar sensor software tab b.
  • Page 10 f) If you don’t see the DRS listed after the initialization, proceed to the following steps: a. Power OFF and Power ON the DRS. This can be done by cutting the power to the PSU or by disconnecting and reconnecting the DRS power cable to the DRS b.