Table of Contents
Advertisement
Quick Links
Installation and Assembly
Swivel Arm for 32" - 50" Plasma Screens
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
- Universal Articulating
Models: PLA 50-UNL, PLA 50-UNL-S,
PLA 50-UNLP, PLA 50-UNLP-S,
RTPLA50-S
Maximum Load Capacity: : : : : 150 lb (68 kg)
ISSUED: 06-05-06 SHEET #: 202-9140-3 08-17-06
Advertisement
Table of Contents
Related Manuals for PEERLESS PLA 50-UNL
Summary of Contents for PEERLESS PLA 50-UNL
- Page 1 Installation and Assembly - Universal Articulating Models: PLA 50-UNL, PLA 50-UNL-S, PLA 50-UNLP, PLA 50-UNLP-S, Swivel Arm for 32" - 50" Plasma Screens RTPLA50-S Maximum Load Capacity: : : : : 150 lb (68 kg) 3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com...
-
Page 2: Tools Needed For Assembly
Read instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-729-0307. -
Page 3: Wall Mount Parts List
Before you start make sure all parts Wall Mount Parts List listed are included with your product. MODEL MODEL PLA 50-UNL RTPLA50-S PLA 50-UNLP PLA 50-UNL-S PLA 50-UNLP-S DESCRIPTION QTY. PART # PART # A wall plate 201-1095 201-4095 B tilt-roll assembly... - Page 4 Before you begin, make sure all parts shown are included with your product. RTPLA50-S Adapter Bracket Parts List PLA 50-UNL PLA 50-UNL-S PLA 50-UNLP PLA 50-UNLP-S Description Qty Part # Part # Part # Part # AA adapter bracket 201-1110...
- Page 5 Security Adapter Bracket Fasteners M4 x 12 mm (6) M6 x 12 mm (4) M5 x 12 mm (4) M8 x 15 mm (6) 510-1079 520-1050 520-1064 M6 x 20 mm (4) 520-1068 520-9554 M5 x 25 mm (4) 520-1122 M8 x 25 mm (4) M4 x 25 mm (4) M6 x 25 mm (4)
-
Page 6: Installation To Wood Stud Wall
Installation to Wood Stud Wall WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. - Page 7 Installation to Concrete Wall WARNING • Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hard- ware and components.
- Page 8 WARNING • If you are uncertain that product is properly installed, call customer care. Note: There are five mounting positions. The center position is shown (right). Slide washer (J) over wall support arm axle (D). Next, insert plastic cap (N) into axle. Then, insert holding pin (M) into axle.
- Page 9 Attach two pieces of vinyl trim (E) to wall plate (A). Next, attach one piece of vinyl trim to bottom of swivel box on arm assembly (C). Insert one finishing cap (L) into each unused hole of wall plate (A). SWIVEL BOX Insert and tape carriage bolt (I) into top hole of tilt-roll assembly (B).
- Page 10 WARNING • Use an assistant or mechanical lifting equipment to safely lift and position the plasma TV. Insert two M10 screws (F) into swivel box on arm assembly (C) as shown. Leave approx. 1/4" of exposed thread. SWIVEL BOX .25" Hook tilt-roll assembly (B) onto M10 screws (F).
-
Page 11: Installing Adapter Brackets
Installing Adapter Brackets Refer to Screen Compatibility Chart to determine the proper fasteners to use. To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached. Place adapter brackets (BB or CC) on back of screen, align to holes, and center on back of screen as shown in figure 7.1. -
Page 12: Mounting And Removing Flat Panel Screen
Mounting and Removing Flat Panel Screen Refer to mount instruction sheet for attachment of adapter bracket to mount. Hook adapter brackets (BB or CC) onto adapter bracket (AA), then slowly swing screen in as shown. Turn screws clockwise at least six times to prevent screen from being removed as shown in detail 4. Tighten using allen wrench (DD). Screen can be adjusted horizontally if desired. - Page 13 13 of 13 ISSUED: 06-05-06 SHEET #: 202-9140-3 08-17-06 ©2006 Peerless Industries, Inc. All rights reserved. Peerless is a registered trademark of Peerless Industries, Inc. All other brand and product names are trademarks or registered trademarks of their respective owners.