Table of Contents
Advertisement
Accessory Storage Case
Accessories
The Accessory Storage Case contains the following accessories:
• Small Chopping/Mixing Blade
• Large Chopping/Mixing Blade
• Dough Blade
Operating the Lock
To unlock, turn the dial at the front of the case anticlockwise to the 'Open' position. Gently lift up
the transparent cover. Do not force the cover open when the dial is in the locked position. To lock,
gently close the cover and turn the dial clockwise to the 'Lock' position.
NOTE: Carefully hold the blades & discs by their center hubs when inserting and removing
from the storage case.
CAUTION: DO NOT TOUCH METAL BLADES OR CUTTING EDGES OF DISCS. ALL ARE
EXTREMELY SHARP AND CONTACT COULD CAUSE INJURY.
Dicing Kit Storage Case
Unpacking & Repacking
1. To open the kit, turn the flat work bowl cover
anticlockwise and lift to remove.
2. Grasp the center hub on the dicing blade and carefully
lift out of the storage case. Set aside on a flat surface.
3. Using the opening in the top of the dicing grid, grip and
lift out to remove.
4. The cleaning tool sits in a dedicated space in the base
of the storage case.
5. When repacking the dicing kit, ensure all the parts are
clean and dry. Repack by inserting parts into the case in
reverse order to the above, beginning with the cleaning
tool and so on.
• Stem Adapter
• Adjustable Slicing Disc (in the right slot)
• Reversible Shredding/Grating Disc
(in the left slot)
1
2
3
4
5
6
1 = Small pusher
2 = Flat work bowl cover lid
3 = Dicing disc
4 = Dicing grid
5 = Cleaning tool
6 = Storage case
10
General Assembly Instructions
Before First Use
Before using your Expert Prep Pro for the first time, wash and dry all the parts thoroughly (see
Cleaning, Storage and Maintenance section).
Work Bowls
• The Food Processor is supplied with two work bowls.
• The large work bowl has a maximum capacity of 3L and can be used with the Large Chopping/
Mixing Blade, Dough Blade, Adjustable Slicing Disc, Reversible Shredding/Grating Disc, Dicing Kit
& Spiralising Kit.
• The small work bowl has a maximum capacity of 0.95L and can be used with the Small Chopping/
Mixing Blade only. When the Work Bowl Cover is fitted, it prevents any leakage into the large work
bowl, allowing you to use the small bowl without the need to wash up the large bowl after use.
N.B. The large work bowl must always be fitted before the small work bowl can be set up inside.
It will not always be possible to use the work bowls to their maximum capacity. The amount of food/
liquid you can process in the bowls will depend on the density of the ingredients in the work bowl
and the consistency of the desired end result. If you find that the motor is struggling or that the
processing results are uneven, then we would recommend that you reduce the amount of ingredients
in the work bowl and instead process in batches.
For liquid, we recommend that you do not fill the bowls above the Maximum Liquid Fill markings on
each bowl (1800ml on the large work bowl and 400ml on the small work bowl.) This is to avoid liquid
spilling into the central spindle which may cause leakage.
Chopping certain foods may scratch or cloud the work bowl; this will not affect the functionality of
the bowls.
Main Work Bowl & Cover Operation
1. Place the food processor base on a dry, level worktop with the controls facing toward you. Do not
plug the unit in until it is fully assembled.
2. Place the Large Work Bowl on the base and use the handle to turn the bowl anticlockwise to lock
it into place.
3. To use the Small Work Bowl, first attach the Large Work Bowl to the base. Place the Stem Adapter
onto the shaft, then lower the Small Work Bowl over the adapter and into the Large Work Bowl.
Place your fingers in the recesses of the Small Work Bowl and turn slightly to secure, until the
bowl drops into place (it will still be possible to move the bowl slightly from side to side).
4. Place the workbowl cover over the large work bowl with the feedtube assembly shifted slightly to
the right of the handle.
5. Once the cover is fully seated, rotate it to the left
(clockwise) to engage the lid-locking mechanism and
interlock. It should click into place.
6. To remove the cover, turn anticlockwise until it will
not turn any further, then lift to release.
NOTE: You cannot remove the work bowl before removing
the work bowl cover.
11
Hide quick links:
Advertisement
Table of Contents
