Compaq 2T-QINTL-CD Installation Information page 2

Installing the Slide Assemblies
The rackmounted CD storage system requires 17.78 cm (7.00 in.) of vertical space or 12 contiguous holes in a
48.26-cm (19-in) EIA cabinet. The bottom hole in this installation area
identified as hole 12 (see Figure 1).
In the following installation procedures, directions are referred to while viewing the rackmounted CD storage
system from the front of the cabinet. To install the slide assemblies, refer to Figure 1 and the following procedures:
1. Remove the inner races from the right and left slide assemblies. Set the inner races aside.
2. Attach the right front slide bracket
› œ
, split washers , and 8-32 hex nuts
3. Attach the right rear slide bracket
› œ
, split washers , and 8-32 hex nuts
4. . Attach the left front slide bracket
› œ
, split washers , and 8-32 hex nuts
5. Attach the left rear slide bracket
œ
split washers , and 8-32 hex nuts
6. Place the right front slide bracket
ž
with the two slide bracket holes and with the 2nd and 4th holes of the installation area on the right front rail.
Install two 10-32 truss-head screws
slide bracket to the right front rail.
7. Place the right rear slide bracket
with the two slide bracket holes and with the 2nd and 4th holes of the installation area on the right rear rail.
Install two 10-32 truss-head screws
slide bracket to the right rear rail. Tighten the two 8-32 pan-head screws
right rear slide bracket to the right slide assembly.
8. Place the left front slide bracket
with the two slide bracket holes and with the 2nd and 4th holes of the installation area on the left front rail.
Install two 10-32 truss-head screws
slide bracket to the left front rail.
9. Place the left rear slide bracket
with the two slide bracket holes and with the 2nd and 4th holes of the installation area on the left rear rail.
Install two 10-32 truss-head screws
slide bracket to the left rear rail. Tighten the two 8-32 pan-head screws
left rear slide bracket to the left slide assembly.
10. Attach the right inner race to the right side of the CD storage system chassis and the left inner race to the left
side of the CD storage system chassis.
11. Pull both slide assemblies out fully to their locked positions, then lift the chassis and position it so that the inner
races fit into the front end of the slide assemblies. Push the chassis into the slide assemblies until it stops, then
release the two locking levers and push the chassis all the way into the cabinet.
Installing the Interlock System
In the following installation procedures, directions are referred to while viewing the rackmount CD storage system
from the rear of the cabinet. To install the interlock system, refer to Figure 1 and the following procedures:
1. Mount the interlock actuator
¡
head screws .
2. Remove the screws securing the vertical rod's bottom mounting bracket to the cabinet and slide the mounting
bracket off the bottom of the vertical rod.
3. Slide the actuator latch
™
to the right slide assembly with two 8-32 pan-head screws

.
™
to the right slide assembly with two 8-32 pan-head screws

, but do not tighten.
™
to the left slide assembly with two 8-32 pan-head screws

.
™
to the left slide assembly with two 8-32 pan-head screws

, but do not tighten.
™
on the inside of the right front rail and align two holes of the 10-32 nut bar
Ÿ
in the 2nd and 4th holes of the installation area to secure the right front
™
on the inside of the right rear rail and align two holes of the 10-32 nut bar
Ÿ
in the 2nd and 4th holes of the installation area to secure the right rear
™
on the inside of the left front rail and align two holes of the 10-32 nut bar
Ÿ
in the 2nd and 4th holes of the installation area to secure the left front
™
on the inside of the left rear rail and align two holes of the 10-32 nut bar
Ÿ
in the 2nd and 4th holes of the installation area to secure the left rear
on the upper right rear of the CD storage system chassis using two 6-32 truss-
¢
for the CD storage system onto the bottom of the vertical rod.
—
is identified as hole 1 and the top hole is
š
and 8-32 hex nuts
š
and 8-32 hex nuts
2
š
, flat washers
š
, flat washers
š
, flat washers
š ›
, flat washers ,
ž

that secure the
ž
ž

that secure the