Advertisement
Quick Links
Compaq StorageWorks
Fibre Channel
Switch, 8-/16-Port
Universal
Mounting Kit
Open Card Completely Before
Beginning Installation Procedures
© 2001 Compaq Information Technologies Group, L.P.
Compaq, the Compaq logo, and StorageWorks are trademarks of Compaq
Information Technologies Group, L.P.
All other product names mentioned herein may be trademarks of their
respective companies.
Compaq shall not be liable for technical or editorial errors or omissions
contained herein. The information is provided "as is" without warranty of
any kind and is subject to change without notice. The warranties for
Compaq products are set forth in the express limited warranty statements
accompanying such products. Nothing herein should be construed as
constituting an additional warranty.
Printed in the U.S.A.
Fibre Channel Switch, 8-/16-Port Universal Mounting Kit
Third Edition (November 2001)
Part Number: EK-GGAAB-IA. C01
Compaq Computer Corporation
About This Card
This card identifies the contents of the universal mounting kit
and provides procedures for mounting Fibre Channel 8-port
(380591–B21/ DS–DSGGA–AA or 176219–B21/
DS–DSGGC–AA) and 16-port (380578–B21/
DS–DSGGA–AB or 212776–B21/DS–DSGGC–AB) switches
into the following Compaq racks:
•
RETMA 41U or 42U
•
Compaq Classic
•
Metric SW600
Kit Contents
1
2
NOTE: This kit contains parts for multiple rack installations. Not all kit parts
are needed for all rack installations.
1 Mounting brackets (2)
2 Extender brackets (2)
3 Slide brackets (2)
4 Bag of miscellaneous hardware:
•
Snap-on cable ties (2)
•
Clip nuts (4)
•
Alignment washers (8)
•
Pan head SEMS screws, 10-32 x 9/32 inches (4)
•
Pan head SEMS screws, 10-32 x 5/8 inches (16)
•
Flat washers for #10 screws (4)
•
Pan head SEMS screws, 8-32 x 1/4 inches (4)
•
Flat washers for #8 screws (4)
Tools Required
•
No. 2 Phillips screwdriver
4
3
CXO7467B
Advertisement
Related Manuals for Compaq 158223-B21
Summary of Contents for Compaq 158223-B21
-
Page 1: Tools Required
Compaq StorageWorks About This Card This card identifies the contents of the universal mounting kit and provides procedures for mounting Fibre Channel 8-port Fibre Channel (380591–B21/ DS–DSGGA–AA or 176219–B21/ DS–DSGGC–AA) and 16-port (380578–B21/ DS–DSGGA–AB or 212776–B21/DS–DSGGC–AB) switches Switch, 8-/16-Port into the following Compaq racks: •... - Page 2 Installation Process Orientation • For 1.5U 16-port switches, see Figure 2. The current or planned configuration of rack components determines which installation process orientation to follow. A key consideration is whether the cables are routed at the front or rear of the rack. General rack configuration guidelines include: •...
-
Page 3: Attaching The Mounting Brackets
Attaching the Mounting Brackets RETMA 42U and Compaq Classic Racks 1. Connect an extender bracket to each mounting bracket (see Attach two mounting brackets, using the appropriate procedure Figure 5) and finger-tighten two pan head SEMS screws for the rack type. (10-32 x 5/8 inches). - Page 4 Metric Racks • For newer 8-port switches (176219–B21/DS–DSGGC–AA), see Figures 9 and 10. 1. Position each mounting bracket (see Figure 7, 1) with the Use four pan head SEMS screws (8-32 x 1/4 inches) and rail holes pencil-marked M. four flat washers to attach the mounting brackets to the switch.
- Page 5 • For 1.5U 16-port switches (such as 212776–B21/ — For cable-rear installations in an upper location, attach DS–DSGGC–AB)—Positioned approximately three inches the brackets as shown in Figure 13. from the rack front for cable-front installations (see Figures 11 and 12), or one inch from the rack-front for cable-rear installations (see Figures 13 and 14).
- Page 6 Installing the Switch into the Rack • For 2U 16-port switches (such as 380578–B21/ DS–DSGGA–AB) in rack-front and rack-rear installations, see Figures 15 and 16. CAUTION: Keep the switch parallel to the floor while sliding the Use four pan head SEMS screws (10-32 x 9/32 inches) and slide brackets into the mounting brackets.
- Page 7 Routing Power and Data Cables IMPORTANT: All switches use the same cable routing method, so a representative example is used here to illustrate this process. Install a snap-on cable tie into each slide bracket, as shown in Figure 19 (representative example), as desired, and route the power cables downward along the rack vertical rail.