Advertisement
Quick Links
RM Tape Library Interlock Kit Installation Information
EK-TPLBR-IN. A01
May 1999
Introduction
The 2T-QINTL-TL interlock kit contains the components for installing the slide assemblies, the interlock system,
and the shipping bracket on the rackmounted tape library. The interlock system helps prevent cabinet instability by
allowing only one system at a time to be pulled out of the cabinet. The shipping bracket is used to secure the tape
library in the cabinet during shipment or when moving the cabinet to a new location.
The interlock system consists of a vertical rod, on which are mounted actuator latches for each product installed in
the cabinet. These actuator latches engage the interlock actuator on the rear of rackmount systems. When a
rackmount system is pulled out of the cabinet, the actuator latches rotate to prevent any other rackmount system that
has an interlock actuator from being pulled out of the cabinet.
Table 1 lists the parts that are shipped with the 2T-QINTL-TL interlock kit. The callouts in column 1 refer to the
part location in Figure 1.
Table 1 2T-QINTL-TL Interlock Kit Parts List
Callout
Description
™
Slide bracket, right and left front
š
Slide bracket, right and left rear
›
8-32 pan-head screw
œ
Flat washer, .190ID x .051THK
Split washer, .171ID
ž
8-32 hex nut
Ÿ
M6 nut bar
Interlock actuator
¡
6-32 truss-head screw
¢
Stabilizer bracket
Actuator latch
10-32 threaded nut bar
‘
10-32 truss-head screw
’
6-32 truss-head screw
“
Shipping bracket
”
8-32 truss-head screw
•
Flat washer, .221ID x .051THK
–
8-32 Kep nut
—
Flat washer, .286ID x .066THK
˜
Split washer, .263ID
1
M6 screw
2
Cage nut
RM Tape Library Interlock Kit Installation Information
© Compaq Computer Corporation. 1999. All Rights Reserved.
®
Compaq and the Compaq logo are registered in the United States Patent and Trademark Office.
Part Number
Qty.
12-44537-01
2
12-44537-02
2
90-06038-01
8
90-06660-00
8
90-06690-00
8
90-06561-00
8
74-53977-02
4
74-60570-01
1
90-00063-15
2
74-48996-01
1
74-48997-02
1
74-48998-01
1
90-00063-39
2
90-00063-10
2
74-60569-01
1
90-00063-22
2
90-06664-00
2
90-06563-00
2
90-06676-00
2
90-07797-00
2
90-40005-16
2
90-11476-01
2
EK-TPLBR-IN
1
Advertisement
Related Manuals for Compaq 2T-QINTL-TL
Summary of Contents for Compaq 2T-QINTL-TL
- Page 1 Table 1 lists the parts that are shipped with the 2T-QINTL-TL interlock kit. The callouts in column 1 refer to the part location in Figure 1.
- Page 2 Installing the Slide Assemblies The rackmount tape library requires 35.56 cm (14.00 in.) of vertical space or 24 contiguous holes in a 48.26-cm (19- in) EIA cabinet. The bottom hole in this installation area (4) is identified as hole 1 and the top hole is identified as hole 24 (see Figure 1).
- Page 3 6-32 set screws to secure the actuator latch to the vertical rod. 9. Now tighten the screws to secure the vertical rod’s bottom mounting bracket. Figure 1 Installing the 2T-QINTL-TL Interlock Kit LJ-06688...
- Page 4 Installing the Shipping Bracket In the following installation procedures, directions are referred to while viewing the rackmount tape library from the rear of the cabinet. The shipping bracket is used to secure the tape library in the cabinet during shipment or when moving the cabinet to a new location.
Need help?
Do you have a question about the 2T-QINTL-TL and is the answer not in the manual?
Questions and answers