Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for BE BE-12000ER
Summary of Contents for BE BE-12000ER
- Page 1 PORTABLE GAS GENERATOR User Manual BE-12000ER...
-
Page 2: Table Of Contents
TABLE OF CONTENTS TABLE OF CONTENTS Introduction Stopping the Generator Using the Operators Manual 23 Disconnect Load 23 Turn Off The Engine Switch Product Identification 24 Close The Fuel Valve Lever Generator Storage Engine 24 Drain The Fuel Safety 24 Protective Treatment Safety Rules Transporting Hazard Symbols and Meanings... -
Page 3: Introduction
The operating manual is an important part of your generator. It should record the information in the places provided below. be read thoroughly before initial use, and referred to often to make sure adequate safety and service concerns are being addressed. -
Page 4: Safety
Even if you can’t smell exhaust fumes, you may still be exposed to carbon monoxide. NOTICE indicates a situation that could result in equipment damage. • NEVER operate the generator in an explosive atmosphere, near Follow safety messages to avoid or reduce the risk of injury or death. -
Page 5: Ground Fault Circuit Interrupter Protection
• Do not refill fuel tank while the engine is running. Before refueling the generator, turn it off and let it cool down. Gasoline spilled on hot A GFCI can be used only with generators that have the neutral wire engine parts could ignite. -
Page 6: Important Safety Instructions
If generator has been covered to protect if is properly grounded. from the weather during non use, be sure to remove it and keep it well away from the area during generator use. This generator is equipped with a grounding terminal for added •... - Page 7 Current outdoors, use only extension cords marked “For Outdoor Use”. Hertz Frequency (1Hz=60 r/min) Extension cords, when not in use should be stored in a dry and well ventilated area. Watt Power • Always switch off generator’s AC circuit breaker and disconnect tools...
-
Page 8: Generator Components
22) Cover, Generator End Starts up the generator. If the unit has not been 23) Muffler Battery used for more than 3 months, it may need to be 24) Cylinder Head replaced. 25) Carburetor Measures the engine’s oil level. Make sure engine’s... -
Page 9: Sockets
GENERATOR COMPONENTS SOCKETS Ensure the generator is safely grounded. For the Grounding Sockets can be any of the following patterns depending on local grounding method, refer to the Page 19. Make Terminal electrical regulations and codes. sure unit is fully grounded before use. -
Page 10: Features
FEATURES OPERATION Features Operation UNIT GROUNDING MODEL BE-12000ER Place the machine outdoors. Use wire of no less than 2.5mm to ensure AC OUTPUT the grouding terminal is connected to the ground. One end of the wire Frequency 60Hz is pressed below the butterfly nut of the unit, while the other end is... -
Page 11: Filling Fuel
84. The fuel meter by the cap will position. Do not use the choke valve to power the unit down as this can show how full the tank is. Do not overfill the gas tank, as there must be damage your engine permanently. -
Page 12: Start The Generator Recoil Start
OPERATION OPERATION START THE GENERATOR (RECOIL START) CONNECT TO LOAD Pull the wire gently until you feel resistance. Once resistance is felt, pull the Comnnect electric equipment and turn the circuit breaker to ON. Do not recoil starter briskly. You may need to do this twice in quick succession. Do connect more than one load at a time. -
Page 13: Close The Fuel Valve Lever
(see fig.2). PROTECTIVE TREATMENT The unit should be stored in a clean and dry place. It should also be kept away from extreme temperatures. Shield the unit with the box it came in or use a generator cover to protect it from dust build-up and moisture. -
Page 14: Accessories
Strainer Fuel Tube Replace Every 2 Years (2) Maintenance should be conducted more frequently if the unit is used in a dirty or dusty environment. Failure to follow scheduled maintenance could result in damage that is not covered by warranty. -
Page 15: Replace Engine Oil
5) Measure the spark plug gap with a gap gauge. Twist the side 3) If the foam cleaner element is dirty, spray some household cleaning electrode to adjust the gap. The gap should be kept between 0 70 agent onto a cleaning pad. Scrub the filter lightly until clean and and 0 80mm. -
Page 16: Valve Clearance
MAINTENANCE TROUBLESHOOTING VALVE CLEARANCE Troubleshooting Remove the cylinder head cover and measure the valve clearance with TROUBLESHOOTING CHART the feeler gauge. The clearances are 0.03~0.05mm for the inlet valve and 0.05~0.07mm for the outlet valve. PROBLEM CAUSE CORRECTION No fuel Fill the oil tank with gasoline The oil switch is not... -
Page 17: Troubleshooting Analysis
· Suitable temperature: -15°-40°. · Suitable humidity: lower than 95%. · Suitable altitude under 1,000 meters. Unit should be used with lower power in regions higher than 1,000 meters. · The generator can only provide the rated power if used in the conditions listed above. - Page 18 DIAGRAMS ELECTRICAL SCHEMATIC DIAGRAM 2 60HZ 120V/240V...
- Page 19 THE POWER YOU NEED. If you need assistance with the assembly or operation of your Generator please call 1-866-850-6662...
Need help?
Do you have a question about the BE-12000ER and is the answer not in the manual?
Questions and answers