Table of Contents
Advertisement
Quick Links
HEATING & COOUNG
Visit www.carrier.cmn
SYSTXCCUID01
Infinity Control TM
Installation and Start-Up Instructions
Infinity Control
TM
SYSTXCCUID01
A03149
NOTE:
Read
the
entire
instruction
manual
before
starting
the
installation.
This symbol
=-> indicates
a change
since the last issue.
TABLE
OF CONTENTS
SAFETY
CONSIDERATIONS
.....................................................
1
INTRODUCTION
..........................................................................
1
INSTALLATION
AND
START-UP
OVERVIEW
......................
1
INSTALLATION
...........................................................................
2
INITIAL
POWER-UP
....................................................................
5
QUICK
START ..............................................................................
6
INSTALL
/ SERVICE
MENUS
....................................................
7
OPERATIONAL
INFORMATION
.............................................
11
TROUBLESHOOTING
...............................................................
12
SAFETY
CONSIDERATIONS
Read
and follow
manufacturer
instructions
carefully.
Follow
all
local electrical
codes during
installation.
All wiring
must conform
to local
and national
electrical
codes, hnproper
wiring
or installa-
tion
may
damage
Infinity
Control
System.
Recognize
safety
information.
This is the safety-alert
symbol
Z_x • When you see this
symbol
on the equipment
and in the instruction
manual,
be alert to
the potential
for personal
injury.
Understand
the signal
words
DANGER,
WARNING,
and CAIfTION.
These
words
are used
with
the safety-alert
symbol.
DANGER
identifies
the most
serious
hazards,
which
will result
in severe
personal
injury
or death.
WARNING
signifies
a hazard,
which
could
result
in personal
injury
or death.
CAUTION
is used to
identify
unsafe
practices,
which
would
result
in minor
personal
injury or product
and property
damage.
NOTE
is used to highlight
suggestions
which
will result
in enhanced
installation,
reliability,
or operation.
INTRODUCTION
The Infinity
System
consists
of intelligent
communicating
com-
ponents
(User Interface,
variable
speed furnace
or fan coil, AC or
HP),
which
continually
communicate
with
each
other
via
a
four-wire
connection
called the ABCD
bus. Conventional
24-volt
signals
on dedicated
wires
are not needed.
Commands,
operating
conditions,
and
other
data
are passed
continually
between
the
components
over
the ABCD
bus.
The result
is a new
level
of
comlbrt,
versatility,
and simplicity.
An Infinity
System
consists
of a Infinity
Control
TM
(themmstat
plus much
more)
and an Infinity
furnace
or fan coil. All Infinity
furnaces
or ban coils
are
variable-speed
and
nmlti
stage
for
maximum
flexibility,
efficiency,
and comlbrt.
They
support
con-
trolled
ventilation,
humidification,
dehumidification,
and air qual-
ity control.
Either
an Infinity
dual capacity
(communicating),
or a
standard
24 vac controlled
outdoor
unit may be used.
When using conventional
outdoor
units,
the Infinity
furnace
or fan
coil provides
the 24 volt signals
needed
to control
them. Also, the
Infinity
Network
Interface
Module
(NIM)
allows
connection
of a
conventional
HRV or ERV without
the need
for a separate
wall
control.
All system
components
are controlled
through
the wall mounted
Infinity
Control
TM,
which replaces
the conventional
thermostat
and
provides
the homeowner
with
a single
wall
control
for all the
features
of the system.
INSTALLATION
AND
START-UP
OVERVIEW
This instruction
covers
installation
of the Infinity
Control
TM
only.
Physical
installation
instructions
for the indoor,
outdoor
equipment
and accessories
are provided
with each unit.
Setup,
commissioning,
operation,
and
troubleshooting
of the
Infinity
System
is covered
only in this installation
instruction.
It is
your guide to connecting
the system
components
and commission-
ing the system
once
all the
physical
components
are installed.
Special
screen prompts
and start-up
capabilities
are provided
in the
Infinity
System
to simplify
and
lead
you
through
the
initial
connnissioning
of the system.
So:
Install
the Infinity
ControV M according
to this instruction.
Install
the indoor
unit, outdoor
unit, and accessories
according
to their instructions.
Wire the complete
system
according
to this instruction.
Setup,
commission,
and operate
the system
according
to this
instruction
to
assure
yourself
a smooth
and
trouble
free
start-up.
Manufacturer
reserves the right to discontinue,
or change at any time, specifications
or designs
without notice
and without incurring obligations.
_m
PC 101
Catalog
No
809-50020
Printed in USA.
Form UID01-1Sl
Pg 1
01-04
Replaces:
NEW
isc
Advertisement
Table of Contents
