Page 1
JM4320 Manioc Planter Instructions Manual IDENTIFICATION Owner: ............................................Address ......................................Nº ....Phone ................. City ................State ....Zip Code .........- ..Machine Model ..................Serial Number ..................Year of Manufacture ................Invoice Nº ....................Date ../ ../ ..
Page 2
JUMIL’s obligation to extend said improvements / modifications to previously sold products or models. 2.8. JUMIL will not be held liable to pay indemnities of any kind due to harvest losses resulting from the inadequate setting of devices comprising...
JUMIL and its dealer network will always be ready to provide you with the required technical clarifications and orientations needed for your equipment.
3D) design and analysis techniques and the most advanced CAD and CAE software. With these powerful workstations in a global vision of, Jumil idealized this new implement, standardized by means of POT (Product Optimization Technology). JM4320 MANIVA basically consists of:...
Page 6
In case of doubt, consult our technical services through telephone 55 (0xx16) 660-1061, fax (16) 3660-1116, or visit our website at www.jumil.com.br. Jumil and its dealer will be at your disposal to assist you permanently with your MANIVA. You are the reason for our search of continuous betterments.
JM4320 Manioc Planter Instructions Manual 3 – SAFETY NORMS Incorrect use of this equipment may result in serious or even fatal accidents. before putting the implement into operation, carefully read this manual as well as the tractor’s manual. Ensure that the person responsible for the operation has been instructed on the correct, safe use of the implement, having read and understood this machine’s manual.
Page 8
JM4320 Manioc Planter Instructions Manual 9) Do not wear loose or very clearance clothes to prevent them from tangling up with moving machine parts (cardan, belts, chains or gear in motion); 10) On coupling and decoupling the equipment, use adequate IPE(s) (protection gloves);...
Page 9
JM4320 Manioc Planter Instructions Manual Specific: 1) Pay attention on getting close to the cutting disks and equipment articulated parts; 2) On circulating with the machine on roads, put the stub trays in the vertical position; 3) The seats may only be used by the planter’s operators in planting conditions, never in transport conditions and always with the use of seat belt;...
Page 10
JM4320 Manioc Planter Instructions Manual c) Long boots or boots with gaiters for activities involving risk of poisonous animal attacks; The Worker should wear the Individual Protection Equipment indicated for the respective tasks in order to protect them. NOTE: All IPEs purchased must come with Approval Certificate issued by the brazilian Ministry of Labor and Employment with effective validity.
Page 11
JM4320 Manioc Planter Instructions Manual ATTENTION MR. OWNER Check and fulfill NR 31 – Regulatory Norm of Safety ad Health at Work in Agriculture, Livestock, Forestry, Forest Exploration and Aquiculture (Executive Ruling No. 86, 03/03/05 – Federal Official Gazette of Mar/04/05), which is aimed at establishing the precepts to be followed...
JM4320 Manioc Planter Instructions Manual 4- PRODUCT SPECIFICATIONS MODEL JM4320 MANIOC PLANTER * Number of Lines 2 units with spacing variation of 0.80 - 1.20 m Coupling 3-Point hydraulic system Wheels Military tire 5.60- 15 four linings 235 liters Fertilizer Tank Capacity...
JM4320 Manioc Planter Instructions Manual 5.1 - Accompanying Components Carefully check the items that come with the machine: DESCRIPTION QUANTITY CODE 27.40.200 Right helical worm thread 27.40.201 Left helical worm thread 5.2 - Chassis Monoblock chassis with tubular structure of high...
JM4320 Manioc Planter Instructions Manual 5.5 – Stub Cutting Fig. 004 Rotor system equipped with three guillotine blades and flexible pullers for the cutting of manioc, the standard rotor cuts manioc of 18 cm and the optional rotor cuts manioc of 13 cm.
JM4320 Manioc Planter Instructions Manual 5.7 – Operator Seat Comfortable individual seat with seat belt. Fig. 007 5.8 – Stub Tray System of stub tanks made up of an articulated base and lateral poles, designed in suitable shape and position for best handling of the stubs by the operator.
JM4320 Manioc Planter Instructions Manual 5.10 – Manioc Distribution Unit System made up of 17” parallel double disk with toboggan type conductor for drainage of maniocs and plows of adjustable position, manioc tightening tread and adjustment rods with spring. Fig. 010 6 –...
JM4320 Manioc Planter Instructions Manual 6.3 – Fertilizer Furrower Chisel Fertilizer system with adjustable system for lateral fertilizing, depth and retractable pointer. Fig. 013 7- PRODUCT ASSEMBLY The machine leaves the plant already assembled, therefore, it only requires following the preparation procedures to begin operation.
JM4320 Manioc Planter Instructions Manual 8 – PREPARATION FOR USE 8.1 – Tire Precautions To ensure long tire life of your implement, the following precautions should be taken: The conditions of culture remains have a significant effect on the service life of tires so avoid leaving plantation remains high enough to hinder the rolling of tires.
JM4320 Manioc Planter Instructions Manual 8.2 – Coupling the Machine to the Tractor The three-point system of the hydraulic device allows a single person to carry out the coupling operation. Therefore, choose a flat site and proceed as follows: Previously align the tractor and the machine and while in idling...
JM4320 Manioc Planter Instructions Manual 8.3.2 – Manioc Cutting 1,00 to 1,50 mm manioc cutting system is made up of two rotors that act in inverse direction, thus characterizing the guillotine effect. 0 to The coordinated motion 2,0 mm of the blades is essential for the cutting efficiency.
JM4320 Manioc Planter Instructions Manual 8.3.4 – Fertilizer Furrower (Optional) The fertilizer furrower chisel assembly is used optionally in cases in which one wishes to deposit the fertilizer at a greater depth and also without being in direct contact with the manioc. In this case, the furrower chisel support (“a”...
JM4320 Manioc Planter Instructions Manual 8.3.6 - General retightening of the machine Proceed to general retightening of the machine, especially the bolts fastening the drive and transport wheels, as well as the fastening clamps of the planting units and fastening claws of the hydraulic lift.
5 km/hr. Thus, setting of the manioc quantity is an important factor for successful planting, so pay attention on performing this activity. Your JM4320 has a setting change per planting unit. Perform the same setting for both units to guarantee a uniform stand.
JM4320 Manioc Planter Instructions Manual 9.3 - Fertilizer Distribution The fertilizer flow is made through individual conductor worm threads, and the different dosages are obtained by means of the fertilizer distribution gear. The indicative table that Fig. 021 follows was developed for an...
Page 29
JM4320 Manioc Planter Instructions Manual KILOGRAMS PER HECTARE TRANSMISSION RATIO SPACING IN CENTIMETERS DRIVE DRIVEN 1” THREAD MANIOC FERTILIZER DISTRIBUTION TABLE 2” THREAD MANIOC FERTILIZER DISTRIBUTION TABLE 1014 1023 1193 1392 1404 1432 1671 1685 1966...
JM4320 Manioc Planter Instructions Manual 9.3.1 – Calculation to determine fertilizer distribution quantity As we have said, although the table was elaborated based on test results, it should be followed as basic orientation, since the specific weight of the fertilizer varies much from brand to brand, formula, batch, etc.
JM4320 Manioc Planter Instructions Manual 9.4 - Manioc Depth Control Manioc depth control is obtained by positioning the jaw (“a” and “b” fig. 22), the jaw (“a” fig. 22) upwards for greater depth, downwards for lesser depth, and the jaw (“b” fig. 22) upwards for greater spring pressure, and downwards for lesser spring pressure.
JM4320 Manioc Planter Instructions Manual 9.6 – Tightening Wheel Setting The tightening wheel is an important element in the planting system, its effective action gives the right settling of manioc in the soil. For this, adjust the working pressure by positioning the lock (“a”...
JM4320 Manioc Planter Instructions Manual 9.7 - Manioc Distribution Change To set the distance between maniocs, proceed as follows: 1 – knowing the space between maniocs, consult the distribution table attached to the fertilizer distribution change chain guard and note that there is a column for 13 cm maniocs and another column for 18 cm maniocs.
JM4320 Manioc Planter Instructions Manual 9.8 - Fertilizer Distribution Change To set the quantity of fertilizer per hectare, proceed as follows: 1 – knowing the quantity of fertilizer to be distributed per hectare, consult the distribution table attached to the side of the fertilizer tank and note the various columns referencing the spacing between lines.
JM4320 Manioc Planter Instructions Manual 9.10 – Broad Tread Compacter Wheel Setting (Optional) The broad tread compacter wheel is an optional element in the planting unit. It can work with or without pressure on the soil, this occurs due to factors like air bag elimination and need for greater or lesser contact of the soil with the manioc.
JM4320 Manioc Planter Instructions Manual 9.12 – Retractable Fertilizer Furrower Chisel Setting. (Optional) The furrower chisel can work on the same line or beside the manioc planting line. this, position support (“a” fig. 31) using the bolts (“b” Fig. 31).
JM4320 Manioc Planter Instructions Manual 10 - LUBRICATION The running efficiency of any machine relies much on suitable lubrication and it is therefore fundamental to ensure proper and quality lubrication to prevent reduction in the equipment efficiency, leading to early wear of parts.
Page 41
JM4320 Manioc Planter Instructions Manual Fig. 032 Fig. 031 Manioc Feeder Fertilizer Distributor shielded bearings have special packing that protect against entry of impurities inside the bearing, mounted with additive formula lubricant that improves the performance and prolongs the service life of the components, even...
Need help?
Do you have a question about the JM4320 and is the answer not in the manual?
Questions and answers