Table of Contents
Advertisement
FOR SERVICE TECHNICIAN ONLY - DO NOT REMOVE OR DESTROY
CODE
J . C 8
COIN/DEBIT OPTION
J . C 8
Both coin & debit selected. Press the QUICK CYCLE button
3 consecutive times to change this selection.
J . C 8
Coins selected, debit disabled. Press the QUICK CYCLE
button 3 consecutive times to change this selection.
J . C 8
Debit Card selected, coins disabled. This is the factory default for
PN models. Press the QUICK CYCLE button 3 consecutive times
to change this selection.
J . E 8
Enhanced Debit is self-selected when a Generation 2 card reader
is installed in the washer. The Ed option cannot be manually
selected or deselected.
Press the DELICATES AND KNITS button once to advance to next code.
L . 0 0
PRICE SUPPRESSION OPTION
This option causes the customer display to show 'ADD' or
'AVAILABLE' rather than the amount of money to add. (Used
mainly in debit installations.)
L . 0 0
Not Selected 'OFF'.
L . PS
Selected 'ON'. Press the QUICK CYCLE button once
to change this selection.
Press the DELICATES AND KNITS button once to advance to next code.
8. C E
CLEAR ESCROW OPTION
When selected, money held in escrow for 30 minutes without
further escrow or cycle activity will be cleared.
8.00
Not selected 'OFF'.
8. C E
Selected 'ON'. Press the QUICK CYCLE button once
to change this selection.
Press the DELICATES AND KNITS button once to advance to next code.
8. 800
TOP SPIN SPEED RPM
8. 800
This can be selected from the following spin speeds: 600 rpm,
750 rpm, 800 rpm, 1000 (displays as 999) rpm. Step between
speeds by pressing the PERMANENT PRESS button. Factory
preset for 800 rpm.
Press the DELICATES AND KNITS button once to advance to next code.
0. 0 0
PENNY INCREMENT OFFSET
0. 0 0
This option is not supported for non-North American models and
the value must be set to 00.
Press the DELICATES AND KNITS button once to advance to next code.
8 1.00
PREWASH LENGTH
8 1.00
This is the number of minutes of PREWASH. Choose 0 to disable
the prewash or select between 2 and 7 minutes by pressing the
PERMANENT PRESS button.
Press the DELICATES AND KNITS button once to advance to next code.
82.03
FINAL SPIN LENGTH
82.03
This is the number of minutes of final high speed spin. Choose
from 3-8 minutes by pressing the PERMANENT PRESS button.
Press the DELICATES AND KNITS button once to advance to next code.
PART NO. W10340707A
EXPLANATION
If cycle counter (9 0C) is selected, the following is true:
1 00 Number of cycles in HUNDREDS.
2 00 Number of cycles in ONES.
This is "VIEW ONLY" and cannot be cleared.
Press the DELICATES AND KNITS button once
to advance to next code.
If money counter (1.0C or 1.C0) is selected, the following is true:
3 00 Number of coins in HUNDREDS.
4 00 Number of coins in ONES.
5 00 Number of coins in HUNDREDTHS
END OF SET-UP PROCEDURES
EXIT FROM SET-UP MODE
PD Models: Reinstall access door.
I
PN Models:
I
If Service Access Code was used to enter set-up mode,
Follow exit instructions in Service Access Code, page 10.
If AA1 plug was removed to enter set-up mode,
Unplug washer or disconnect power.
Open console, reinsert plug into AA1, close console.
Plug in washer or reconnect power.
PN MODELS WITH PROGRAMMING SWITCH:
I
Turn key clockwise and remove.
PAGE 4
1 02 = 200
2 25 = 225
TOTAL CYCLES = 225
3 01 = 100
4 68 = 68
5 75 = .75
TOTAL = 168.75
Hide quick links:
Advertisement
Table of Contents
