Control Set-Up Procedures; Set-Up Codes - Maytag Commercial MHN30PD Manual

FOR SERVICE TECHNICIAN ONLY - DO NOT REMOVE OR DESTROY

CONTROL SET-UP PROCEDURES

IMPORTANT: Read all instructions before operating.
PD Models: Insert service access door key, turn, and lift to remove
I
access door.
PN Models: Remove connector AA1 on the circuit board.
I
Set-up procedures can be entered by using the Service Access
Code (see Service Access Code section, page 10) for PN washers
without a key switch installed.
IMPORTANT: Unplug washer or disconnect power before opening
the console. To access connector AA1:
Unplug washer or disconnect power.
Open console, disconnect plug on AA1, close console.
Plug in washer or reconnect power.
The washer is now in the set-up mode. The lower fabric setting
buttons and the digital display are used to set up the controls. The
display can contain 4 numbers and/or letters and a decimal point.
These are used to indicate the set-up codes and related code
values available for use in programming the washer.
Once the washer has been programmed with a hand held device
using Accu Trac, or a Gen. 2 card reader has been installed, the
washer will be put into dAS mode permanently, and dAS will be
displayed every time set-up mode is accessed.
How to use the key pads to program the controls
1. The PERMANENT PRESS button is used to adjust the values
associated with set-up codes. Pressing this button will change
the value by increments. Rapid adjustment is possible by holding
this button down.
2. The DELICATES AND KNITS button advances through the set-
up codes. Pressing this button will advance to the next available
set-up code. Holding this button down will automatically advance
through the set-up codes at a rate of one (1) per second.
3. The QUICK CYCLE button is used to select or deselect options.
Start Operating Set-Up
NOTE: Prior to operation, a payment system or an OPL kit must be installed.
Before proceeding, it is worth knowing that, despite all of the options
available, an owner can simply choose to uncrate a new commercial
washer, hook it up, plug it in, and have a washer that operates.

SET-UP CODES

The DELICATES AND KNITS button will advance from code to code.
I
The PERMANENT PRESS button will change the code value.
I
The QUICK CYCLE button will select or deselect options.
I
FOR PN MODELS: The set-up codes are the same as for the 'PD'
models except where noted.
The set-up code is indicated by the one or two left-hand characters. The
set-up code value is indicated by the two or three right-hand characters.
NOTE: First code shown in each section is default code for coin equipment.
CODE
6 0 7
REGULAR CYCLE PRICE
6 0 7
Represents the number of coins (coin 1) needed to start the washer;
may adjust from 0-39. (See VALUE OF COIN 1.) Advance from 0-39
by pressing the PERMANENT PRESS button. Factory default of
7 x coin 1.
6 00
PN MODELS ONLY: Factory default of 0 coins.
With coin slide activation, this represents the number of push-in
actuations of a coin slide to start the washer.
6 01 setting would represent one coin slide actuation.
NOTE: For coin slide activation, replacement of the meter case is necessary.
Press the DELICATES AND KNITS button once to advance to next code.
PART NO. W10340707A
EXPLANATION
CODE
7 1 1
WASH LENGTH
7 1 1
This is the number of minutes for WASH. Washer comes from the
factory preset with 11 minutes. Choose from 9-17 minutes by
pressing the PERMANENT PRESS button.
Press the DELICATES AND KNITS button once to advance to next code.
8 0 0
ADDITIONAL RINSE OPTION
This option is either SELECTED 'ON' or NOT SELECTED 'OFF'.
8 0 0
Not Selected 'OFF'.
8 A 8
Selected 'ON'. Cannot be combined with the Super Cycle rinse option.
Press the QUICK CYCLE button once to change this selection.
Press the DELICATES AND KNITS button once to advance to next code.
9 0 0
CYCLE COUNTER OPTION
This option is either SELECTED 'ON' or NOT SELECTED 'OFF'.
9 0 0
Not Selected 'OFF'.
9 0 C
Selected 'ON' and not able to be deselected.
Press the QUICK CYCLE button 3 consecutive times
to select 'ON'. Once selected 'ON' it cannot be deselected.
Press the DELICATES AND KNITS button once to advance to next code.
1. 0 0
MONEY COUNTER OPTION
This option is either SELECTED 'ON' or NOT SELECTED 'OFF'.
1. 0 0
Not Selected 'OFF'.
1. 0 C
Selected 'ON'.
Press the QUICK CYCLE button 3 consecutive times
to select 'ON' and 3 consecutive times to remove (Not
Selected 'OFF'.) Counter resets by going from 'OFF' to 'ON'.
1. C 0
Selected 'ON' and not able to be deselected.
To select 'ON' and not able to be deselected, first select 'ON',
then within two seconds press the QUICK CYCLE button twice,
the PERMANENT PRESS button once, and exit the set-up mode.
Press the DELICATES AND KNITS button once to advance to next code.
2. 0 0
SPECIAL PRICING OPTION
This option is either SELECTED 'ON' or NOT SELECTED 'OFF'.
2. 0 0
Not Selected 'OFF', and next available code will be A.00.
2. S P
Selected 'ON'. Press the QUICK CYCLE button once
to change this selection.
If SPECIAL PRICING OPTION is selected, there is access to codes '3.XX'
through '9.XX'.
Press the DELICATES AND KNITS button once to advance to next code.
OPTIONS TO USE IF SPECIAL PRICING IS SELECTED:
3. 0 7
SPECIAL CYCLE PRICE
3. 0 7
Represents the number of coins (coin 1) needed to start the
washer; may adjust from 0-39. (See VALUE OF COIN 1.) Advance
from 0-39 by pressing the PERMANENT PRESS button. Factory
default of 7 x coin 1.
3. 00
PN MODELS ONLY: Factory default of 0 coins.
Press the DELICATES AND KNITS button once to advance to next code.
PAGE 2
EXPLANATION