Download  Print this page

Pioneer DVR-RT500-S/UXTLCA Training Manual page 31

Vcr & dvd recorder combo
Hide thumbs

Advertisement

1-4: CONFIRMATION OF VSR TORQUE
1. Install the Torque Gauge (JG002F) and Adapter
(JG002B) on the S Reel. Set to the Picture Search
(Rewind) mode. (Refer to Fig.1-4-B)
2. Then, confirm that it indicates 120~180gf•cm.
NOTE
Install the Torque Gauge on the reel disk firmly. Press the
REW button to turn the reel disk.
1-5: CONFIRMATION OF REEL BRAKE TORQUE
(S Reel Brake) (Refer to Fig. 1-4-B)
1. Once set to the Fast Forward mode then set to the Stop
mode. While, unplug the AC cord when the Pinch Roller
Block is on the position of Fig. 1-4-A.
2. Move the Idler Assy from the S Reel.
3. Install the Torque Gauge (JG002F) and Adapter
(JG002B) on the S Reel. Turn the Torque Gauge
(JG002F) clockwise.
4. Then, confirm that it indicates 60~100gf•cm.
(T Reel Brake) (Refer to Fig. 1-4-B)
1. Once set to the Fast Forward mode then set to the Stop
mode. While, unplug the AC cord when the Pinch Roller
Block is on the position of Fig. 1-4-A.
2. Move the Idler Assy from the T Reel.
3. Install the Torque Gauge (JG002E) and Adapter
(JG002B) on the T reel. Turn the Torque Gauge
(JG002E) counterclockwise.
4. Then, confirm that it indicates 30~50gf•cm.
The position at FF mode.
Stop at this position.
The position at
STOP mode.
Caption
DD Unit
Cassette Holder Assy
Torque Gauge/Adpter
(JG002F/JG002B)
S Reel
Pinch Roller Block
Cassette
Opener
Fig. 1-4-A
Torque Gauge/Adpter
(JG002F/JG002B)
T Reel
Fig. 1-4-B
NOTE
If the torque is out of the range, replace the following parts.
Check Item
1-4
Idler Assy / Clutch Assy
S Reel side : S Reel/ Tension Band/Tension
1-5
T Reel side : T Reel/ Brake Band/T Brake Spring
2. CONFIRMATION AND ADJUSTMENT
OF TAPE RUNNING MECHANISM
Tape Running Mechanism is adjusted precisely at the
factory. Adjustment is not necessary as usual. When you
replace the parts of the tape running mechanism because
of long term usage or failure, the confirmation and
adjustment are necessary.
2-1: GUIDE ROLLER
1. Playback the VHS Alignment Tape (JG001 or JG001B).
(Refer to SERVICING FIXTURE AND TOOLS)
2. Connect CH-1 of the oscilloscope to TP101 (Envelope)
and CH-2 to TP3002 (SW Pulse).
3. Press and hold the ATR button on the remote control
more than 2 seconds to set tracking to center.
4. Trigger with SW Pulse and observe the envelope.
(Refer to Fig. 2-1-A)
5. When observing the envelope, adjust the Adjusting
Driver (JG005) slightly until the envelope will be flat.
Even if you press the Tracking Button, adjust so that
flatness is not moved so much.
6. Adjust so that the A : B ratio is better than 3 : 2 as shown
in Fig. 2-1-B, even if you press the Tracking Button to
move the envelope (The envelope waveform will begin to
decrease when you press the Tracking Button).
7. Adjust the PG shifter during playback.
(Refer to the ELECTRICAL ADJUSTMENTS)
NOTE
After adjustment, confirm and adjust A/C head.
(Refer to item 2-2)
CH-1
Envelope
(TP101)
CH-1
Track
CH-2
SW Pulse (TP3002)
Entrance
A
B
Max
A : B
31
Replacement Part
Connect/Tension Arm Assy
/T Brake Arm
CH-2
Track
Fig. 2-1-A
Exit
Max
3 : 2
Fig. 2-1-B

Advertisement

loading

  Related Manuals for Pioneer DVR-RT500-S/UXTLCA

This manual is also suitable for:

Dvr-rt300-s/uxtlca