For The Pool Frame Of Concrete - Covered With Tile/Mosaic; English - Pahlen WIDE User Manual

Skimmer WIDE

For the pool frame of concrete - covered with tile/mosaic

Consult your concrete/waterproofing supplier for any waterproofing and application method.
2 1
13 15
Installation as following:
NOTE! When casting/reinforcing the pool frame work, do not get closer than at
least 50 mm to the stainless materials.
1. Make a hole for the skimmer in the framework, dimensions and placement as
shown in Figure 2.
2. Apply sealer at the joint between the sealing flanges and the skimmer housing
(see Fig. 9).
Pahlén recommends Tec7 as a sealant from Novatech (available from Pahlén) or
Aqua Max from Griffon.
Upon application of the sealant, it is important that the joints are tight, so that no
water can penetrate.
See sealant instruction for preparation, application and hardening.
3. Fasten the skimmer in the mold, so that the flange is in contact with the concrete
wall. NOTE! Non-corrosive material (e.g. steel) may not be closer to the stainless
steel (pipe) than 50 mm.
4. Connect the cable (at least 6 mm²) with a ring from the intake flange to earth
(see item 3 Figure 8). Screw, toothed washer and nut are supplied with the product.
If other components are used, it must be ensured that they are of stainless steel
quality (Min. A4).
5. Prior to sealing; mask the skimmer exposed flange and openings in order to avoid
unsightly stains from concrete splashes.
The openings in the skimmer back edge of the float switch, the overflow and refill
openings can be sealed with supplied plugs, see Fig.11
6. Seal the pool frame.
7. Mount the wall cladding (fix, tile, mosaic, etc.). Make sure that the mounting holes
(see Fig. 10) for fastening the frame are free, so that the mounting frame can be
installed later.
8. Check that the flap cap is properly in place and can move.
9. Assemble the frame and secure it with screws (4x M5x30), see Fig. 8.
10. Mount the front of the frame and secure it with the supplied screws (4x M5x12)
in the second and eighth holes, see Fig. 12.
11. Connect the pipe coupling to the
pool circulation with an appropriate
thread sealant.
12. The position of the skimmer top
should be adjusted in height to the
flooring around the pool. Fix to the
desired height with attached straps.
13. If the skimmer top is shortened or
processed in any other way,
tools only for stainless materials
should be used.
3 5 4 6 7
1 9 17 12 10
1. Fixing strip with a screw M5x12 (2x)
2. Skimmer top
3. Earthing point
4. Countersunk screw M6x30 (4x)
5. Mounting frame
6. Countersunk screw M5x12 (4x)
7. Front
8 8. Flange
1
9. Concrete
9
6
10. Reinforcing bar
10
6
Fig 8.
Surface treatment Designed by: Drawn by: Date
E
The tolerance class in accordance with this Assembly drawing no. Art.no.
part of ISO 2768-mK
Scale
Installationsbild bräddavlopp WM
För poolstomme av thermoblock
Drawing number
Box 728, SE-194 27 Upplands Väsby, Sweden
Phone +46 8 59411050, Fax +46 8 59086880
13
10
11
9
8
10
Approved by:
TK 2016-11-15
Revised by: Date
Rev.no.
M12627 0
E
Box 728, SE-194 27 Upplands Väsby, Sweden
Phone +46 8 59411050, Fax +46 8 59086880
12
20 19
1
Flap cap
Klafflucka
3
A
Concrete wall
Betongstomme
7 6 5 4
Surface treatment
E
The tolerance class in accordance with this
part of ISO 2768-mK

ENGLISH

2 8
Surface treatment Designed by: Drawn by: Date
Betad TK 2016-01-26
The tolerance class in accordance with this Assembly drawing no. Art.no.
15594075
part of ISO 2768-mK
Bräddavlopp WM Scale
1:4
Drawing number
21 22 23
24
2 A
Screw
Skruv M5x25 (4x)
Front
14
Front
15
16
Mountning
Fästram
17
frame
Tail/Mosaic
Kakel/Mosaik
Tail join
Kakelfog
Tail fix
Kakelfix
Designed by: Drawn by: Date Approved by:
TK 2016-11-15
Assembly drawing no. Art.no.
Scale Revised by: Date
Installationsbild bräddavlopp WM
Fig 9.
Approved by:
Revised by: Date
Fig 10.
Rev.no.
M12533 0
Fig 11.
Fig 12.
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
18
7
6
5
4
3
2
1
Item
B
P