Maco A-TS Assembly Instructions Manual
Automatic door lock alu
Hide thumbs
Also See for A-TS:
- Assembly instructions manual (44 pages) ,
- Assembly instructions (2 pages)
Related Manuals for Maco A-TS
Summary of Contents for Maco A-TS
- Page 1 TECHNOLOGY IN MOTION www.maco.eu ASSEMBLY INSTRUCTIONS A-TS Automatic Door Lock Alu EXCLUSIVELY FOR CERTIFIED SPECIALISTS! PROTECT DOOR LOCKS...
-
Page 2: Table Of Contents
Table of Contents Item Page Important Information Use of transportation protection devices Instructions for use 7 - 11 Installation instructions 12 - 17 Set lock for day release function (assembler) Day release element assembly on the lock (assembler) MACO day release opener assembly on the striker plate (assembler) Operating instructions day release (end-customer) Positions Drill and Routing patterns... - Page 3 Item Page openDoor Access Control Solutions 35 - 46 Overview A-TS Transponder Plus A-TS Transponder Keypad and Touchkey A-TS Somfy GU Controller Circuit diagram frame-side Circuit diagram button impulse Circuit diagram toggle switch Routing pattern transponder Routing pattern Keypad / Touchkey BT Routing pattern drive motor incl.
-
Page 4: Important Information
Important Information Target audience This documentation is intended exclusively for specialist companies and certified specialists. The work-steps described here in may only be carried out by certified specialists. Instructions for use • Unless otherwise indicated, measurements are made in millimetres. • Assemble all hardware parts professionally as described in these instructions and observe all safety instructions. • All diagrams are only symbolic. •... -
Page 5: Key
Backset DM Distance E Handle height GM Profile front edge Multi-function latch End lock Sash Rebate Height Case height top Case height bottom Important Information WINDOWS · DOORS · SLIDING DOORS... -
Page 6: Use Of Transportation Protection Devices
Use of transportation protection devices Simple transport protection devices, wedges or blocks ensure a safe transport of the entire door element. Remove only after installation. Transport protection devices position WINDOWS · DOORS · SLIDING DOORS... -
Page 7: Instructions For Use
Instructions for use Never open the lock case! Remove shavings from milled pocket! Drill all holes before installing the lock! Do not force the handle pin through the lock nut! WINDOWS · DOORS · SLIDING DOORS... - Page 8 Instructions for use Close the lock only with the associated key! Do not use force when assembling the cylinder! Do not turn the key using force (external Do not turn the handle and key at the same lever)! time! WINDOWS · DOORS ·...
- Page 9 Instructions for use Only apply load to the handle in the normal As soon as traces of forced use are visible, direction! Apply a maximum force of 15kg in the lock must be replaced the direction of actuation (on the handle)! Double sash doors must not be forced past Do not activate the lock when the door is the inactive leaf!
- Page 10 Instructions for use Do not carry the door by the handle! Do not paint over the latch or deadbolt! WINDOWS · DOORS · SLIDING DOORS...
- Page 11 Instructions for use The door lock (lock case) is delivered with an intensive lubrication of high-performance greases and must NOT be re-greased!! Lubricate the MF-HO locking element 1x annually! Do not use lubricating oil, rust remover, silicon spray etc! Lubricate only with grease or technical Vaseline! Grease the latch and deadbolt 1x annually! * Spray grease (455341), ** Rust remover WINDOWS ·...
-
Page 12: Installation Instructions
Installation Instructions a = faceplate c = latch d = latch insert e = insert leg of latch insert Crank Multi-function latch Release the screw and push forward using the screwdriver! Remove the latch! Turn the latch over and place it on the faceplate (a) so you can press the insert leg (e) of the latch insert (d) under the... -
Page 13: Set Lock For Day Release Function (Assembler)
Installation Instructions Set lock for day release function (assembler) Set day release function Manufacturer delivery state Lock Lock Remove the day release screw Insert the day release screw (2.5mm hex socket) (2.5mm hex socket) Unlock Unlock When the day release is pre-set, the main latch is not operated on motorised operation (door does not automatically spring open)! WINDOWS ·... -
Page 14: Day Release Element Assembly On The Lock (Assembler)
Installation Instructions Day release element assembly on the lock (assembler) Remove the faceplate cover. Position the day release element on the back of the faceplate (directly on the latch above the lock case) and push onto the lock case. Screw on the day release element with the attached TX20 M4x10 screw on the front of the faceplate! WINDOWS ·... -
Page 15: Maco Day Release Opener Assembly On The Striker Plate (Assembler)
Installation Instructions MACO day release opener assembly on the striker plate (assembler) Demount the latch element. Mount the MACO day release opener. Activate the mechanical unlocking using the lever on the day release opener*. * The mechanical unlocking can remain active as the day release is controlled via the day release actuator on the lock (see “Day Release”... -
Page 16: Operating Instructions Day Release (End-Customer)
Push the day release actuator upwards, Push the day release actuator release the handle! downwards! The A-TS basic function, automatic locking, is again active! WINDOWS · DOORS · SLIDING DOORS... -
Page 17: Positions
Installation Instructions Positions Position of latch and Position of striker plate and deadbolt striker plate multi-function latch with hook Pressure adjustment: +/- 2 mm with latches and deadbolt striker plate +/- 1,5 mm with MF-HO striker plate Positioning of notch faceplate = notch striker plate A rebate clearance of 2-6 mm must be adhered to in the installed state! WINDOWS ·... -
Page 18: Drill And Routing Patterns
Drilling and routing patterns Lock case and multi-function latch with hook locking ≤2 41,5 ≤2 15,5 15,5 Notch faceplate DM - 1 17,5 Lock case Recommended cable position for access control WINDOWS · DOORS · SLIDING DOORS... -
Page 19: Latch And Deadbolt Striker Plate 3 Mm
Drilling and routing patterns Latches and shootbolt striker plate 3 mm 2 MF-HO +726 -764 WINDOWS · DOORS · SLIDING DOORS... -
Page 20: Multi-Function Hook Striker Plate 3 Mm
Drilling and routing patterns Multi-function hook striker plate 3 mm 12,5 WINDOWS · DOORS · SLIDING DOORS... -
Page 21: Latch And Deadbolt Striker Plate 6 Mm
Drilling and routing patterns Latches and shootbolt striker plate 6 mm 2 MF-HO +726 -764 *E-opener routing pattern WINDOWS · DOORS · SLIDING DOORS... -
Page 22: Multi-Function Hook Striker Plate 6 Mm
Drilling and routing patterns Multi-function hook striker plate 6 mm *E-opener routing pattern WINDOWS · DOORS · SLIDING DOORS... -
Page 23: Positioning Of Striker Plates
Positioning of striker plates 2 Multi-function latches with hooks, Standard K+730, 1-sash, 3 mm Single striker plate Lock Single piece door striker * Use cover faceplate for higher SRH! Motor for motorised opening WINDOWS · DOORS · SLIDING DOORS... -
Page 24: Standard K+730, 2-Sash, 3 Mm
Positioning of striker plates 2 Multi-function latches with hooks, Standard K+730, 2-sash, 3 mm Front door front edge Lock * Use cover faceplate for higher SRH! Motor for motorised opening WINDOWS · DOORS · SLIDING DOORS... -
Page 25: Low K+605, 1-Sash, 3 Mm
Positioning of striker plates 2 Multi-function latches with hooks, Low K+605, 1-sash, 3 mm Single striker plate Lock Single piece door striker * Use cover faceplate for higher SRH! Motor for motorised opening WINDOWS · DOORS · SLIDING DOORS... -
Page 26: Low K+605, 2-Sash, 3 Mm
Positioning of striker plates 2 Multi-function latches with hooks, Low K+605, 2-sash, 3 mm Front door front edge Lock * Use cover faceplate for higher SRH! Motor for motorised opening WINDOWS · DOORS · SLIDING DOORS... -
Page 27: High K+980, 1-Sash 3 Mm
Positioning of striker plates 2 Multi-function latches with hooks, High K+980, 1-sash 3 mm Single striker plate Lock Single piece door striker * Use cover faceplate for higher SRH! Motor for motorised opening WINDOWS · DOORS · SLIDING DOORS... -
Page 28: High K+980, 2-Sash 3 Mm
Positioning of striker plates 2 Multi-function latches with hooks, High K+980, 2-sash 3 mm Front door front edge Lock * Use cover faceplate for higher SRH! Motor for motorised opening WINDOWS · DOORS · SLIDING DOORS... -
Page 29: Standard K+730, 1-Sash, 6 Mm
Positioning of striker plates 2 Multi-function latches with hooks, Standard K+730, 1-sash, 6 mm Single striker plate Lock Single piece door striker * Use cover faceplate for higher SRH! Motor for motorised opening WINDOWS · DOORS · SLIDING DOORS... -
Page 30: Standard K+730, 2-Sash, 6 Mm
Positioning of striker plates 2 Multi-function latches with hooks, Standard K+730, 2-sash, 6 mm Front door front edge Lock * Use cover faceplate for higher SRH! Motor for motorised opening WINDOWS · DOORS · SLIDING DOORS... -
Page 31: Low K+605, 1-Sash, 6 Mm
Positioning of striker plates 2 Multi-function latches with hooks, Low K+605, 1-sash, 6 mm Single striker plate Lock Single piece door striker * Use cover faceplate for higher SRH! Motor for motorised opening WINDOWS · DOORS · SLIDING DOORS... -
Page 32: Low K+605, 2-Sash, 6 Mm
Positioning of striker plates 2 Multi-function latches with hooks, Low K+605, 2-sash, 6 mm Front door front edge Lock * Use cover faceplate for higher SRH! Motor for motorised opening WINDOWS · DOORS · SLIDING DOORS... -
Page 33: High K+980, 1-Sash 6 Mm
Positioning of striker plates 2 Multi-function latches with hooks, High K+980, 1-sash, 6 mm Single striker plate Lock Single piece door striker * Use cover faceplate for higher SRH! Motor for motorised opening WINDOWS · DOORS · SLIDING DOORS... -
Page 34: High K+980, 2-Sash, 6 Mm
Positioning of striker plates 2 Multi-function latches with hooks, High K+980, 2-sash, 6 mm Front door front edge Lock * Use cover faceplate for higher SRH! Motor for motorised opening WINDOWS · DOORS · SLIDING DOORS... -
Page 35: Opendoor Access Control Solutions
Access Control Solutions Overview In combination with the A-TS: Extremely high level of security by self-constant locking of the steel hooks and the locking bolt. Easy, non-mistakable plug-in connection: Incorrect connection is impossible. Tamper-proof: Control unit protected from unauthorised access. -
Page 36: A-Ts Transponder Plus
Access Control Solutions A-TS Transponder Plus Plug & Play Connection motor – cable transition Power supply 12 - 24 V DC Connection / Cabling Connection motor – access control min. 1.5 A Tension release solution Brown – operating Access Control Solution:... -
Page 37: A-Ts Transponder Keypad And Touchkey
Access Control Solutions A-TS Transponder Keypad and Touchkey Plug & Play Connection motor – cable transition Power supply 12 - 24 V DC Connection / Cabling min. 1.5 A Connection motor – access control solution Tension release Brown – operating... -
Page 38: A-Ts Somfy Gu Controller
Access Control Solutions A-TS Somfy GU Controller Tension release Connections Connection motor – cable transition 1 GND Power supply 12 - 24 V DC 2 Vin +8 - 24V (DC) min. 1.5 A = Power supply 3 IN COM... -
Page 39: Circuit Diagram Frame-Side
openDoor Access Control Solutions Circuit diagram frame-side 12 - 24V DC Plug & Play Connection / Cabling min. 1,5 A Brown – operating voltage Motor minus - Transformer White – operating voltage Brown - Motor plus + Green – control voltage* minus - White + Yellow –... -
Page 40: Circuit Diagram Button Impulse
openDoor Access Control Solutions Circuit diagram button impulse Plug & Play Connection / Cabling 12 - 24V DC Brown – operating voltage min. 1.5 A Motor minus - White – operating voltage Motor plus + Transformer Green – control voltage* minus - Brown - Yellow –... -
Page 41: Circuit Diagram Toggle Switch
openDoor Access Control Solutions Circuit diagram toggle switch Plug & Play Connection / Cabling 12 - 24V DC Brown – operating voltage min. 1.5 A Motor minus - White – operating voltage Motor plus + Transformer Green – control voltage* minus - Brown - Yellow –... -
Page 42: Routing Pattern Transponder
openDoor Access Control Solutions Routing pattern Transponder Plus WINDOWS · DOORS · SLIDING DOORS... -
Page 43: Routing Pattern Keypad / Touchkey Bt
openDoor Access Control Solutions Routing pattern Keypad / Touchkey BT 39,5 39,5 WINDOWS · DOORS · SLIDING DOORS... -
Page 44: Routing Pattern Drive Motor Incl. Connecting Plate And Motor Assembly
openDoor Access Control Solutions Motor routing pattern including assembly of connector plate and motor ≤ 20** 15,5 Lock case Recommended cable position for access control solution 16,2 +0,2 - 0,1 12,2 +0,2 - 0,2 * Control unit for openDoor access control solutions, ** Cable channel for comfort solution, *** Cable for openDoor access control solutions WINDOWS ·... -
Page 45: Cable Transition For Opening Angle ≤110°, Alu 12 Air
openDoor Access Control Solutions Cable transition for opening angle ≤110°, Alu 12 Air R8 at F-16 R10 at F-20 R8 at F-16 R10 at F-20 WINDOWS · DOORS · SLIDING DOORS... -
Page 46: Cable Transition For Opening Angle ≤180°, Alu 4 Air, 12 Air
openDoor Access Control Solutions Cable transition for opening angle ≤180°, Timber 4 Air, 12 Air R8 at F-16 R10 at F-20 30 mm depth Due to the different hinge variations and the resulting drive shafts, the position of the cable tray (dimension X) and the cover plate (dimension Y) must be manually calculated! WINDOWS ·... - Page 47 Notes WINDOWS · DOORS · SLIDING DOORS...
- Page 48 MACO PROTECT Satisfied? MAYER & CO We look forward to your BESCHLÄGE GMBH feedback@maco.eu Alpenstraße 173 Order no. 757776 - Datum: January 2019 - Date of change: March 2019 A-5020 Salzburg All rights reserved and subject to change. Graphic source: MACO Tel.: +43 662 6196-0 This print document is revised regularly.