Maco A-TS Assembly Instructions Manual
Automatic door lock pvc
Hide thumbs
Also See for A-TS:
- Assembly instructions manual (48 pages) ,
- Assembly instructions (2 pages)
Related Manuals for Maco A-TS
Summary of Contents for Maco A-TS
- Page 1 TECHNOLOGY IN MOTION www.maco.eu ASSEMBLY INSTRUCTIONS A-TS Automatic Door Lock PVC Use only for certified specialists! PROTECT DOOR LOCKS...
-
Page 2: Table Of Contents
2 Multi-function latch with hook, Low K+605, 2-sash 2 Multi-function latch with hook, High K+980, 1-sash 2 Multi-function latch with hook, High K+980, 2-sash Lengthening/shortening of the A-TS K+730 27 - 28 Module without additional locking point Module with additional locking point WINDOWS ·... - Page 3 Item Page openDoor Access Solutions 29 - 40 Overview A-TS Transponder Plus A-TS Transponder Keypad and Touchkey A-TS Somfy GU Controller Circuit Diagram frame-side Circuit Diagram button impulse Circuit Diagram toggle switch Milling image Transponder Plus Milling image Keypad / Touchkey BT Milling image including connector plate and motor Cable transition for opening angle ≤ 110°, PVC 12 air...
-
Page 4: Important Notes
Important Notes Target audience This documentation is intended exclusively for specialist companies and certified specialists. The work-steps contained may only be carried out by certified specialists. Instructions for use • Unless otherwise indicated, measurements are made in millimetres. • Assemble all hardware parts professionally as described in these instructions and observe all safety instructions. • All diagrams are only symbolic. • With the spacer-block setting, observe the glazing technical guideline No. 3 for the "Blocking of Glazing Units". • Observe the "Guidelines and Instructions for Product and Liability (GIPL)". • Inform the end user about the contents of the "Guidelines and Instructions for End Users (GIEU)". • Printing errors, mistakes and changes are reserved. Material information • The hardware parts described in this guide are made of stainless steel or galvanised passivated steel and sealed in accordance with DIN EN 12329. They must not be used in environments with aggressive, corrosive air content. -
Page 5: Key
Backset DM Distance E Handle height GM Profile Front Edge Multi-function latch End piece Sash rebate height Case dimension top Case dimension bottom Important note WINDOWS · DOORS · SLIDING DOORS... -
Page 6: Use Of Transportation Protection Devices
Use of transportation protection devices Simple transport protection devices, wedges or blocks ensure a safe transport of the entire door element. Remove only after installation. Transport protection device position WINDOWS · DOORS · SLIDING DOORS... -
Page 7: Instructions For Use
Instructions for use Never open the lock case! Remove swarf from the milled space! Drill all holes before installation of the lock! Do not force the handle pin through the lock nut! WINDOWS · DOORS · SLIDING DOORS... - Page 8 Instructions for use Only close the lock with the corresponding Do not use force during the cylinder operating key! assembly! Do not turn the key using force! Do not simultaneously press the key and handle! WINDOWS · DOORS · SLIDING DOORS...
- Page 9 Instructions for use Only apply load to the handle in the normal As soon as traces of forced use are visible, direction! Apply a maximum force of 15 kg in the lock must be replaced! the direction of actuation (on the handle)! Two-sash doors must not be forced over the Do not close the lock latch when the door is inactive leaf! open! WINDOWS ·...
- Page 10 Instructions for use Do not carry the door leaf with the handle! Do not paint or varnish over the padlock bolt or latch! WINDOWS · DOORS · SLIDING DOORS...
-
Page 11: Instructions For Use
Instructions for use The door lock (lock case) is delivered with an intensive lubrication of high-performance greases and must NOT be re-lubricated! Lubricate the MF-HO locking element 1x annually! Do not use any lubricating oils, rust remover, silicone sprays etc! Lubricate only with grease or technical petroleum jelly! Lubricate the latch and locking bolt 1x annually! * Spray grease (455341), ** Rust remover WINDOWS ·... -
Page 12: Installation Instructions
Installation Instructions a = Faceplate c = Latch d = Latch insert e = insert leg of latch insert Crank latch Multi-function latch Loosen the screw completely and push forward with the screwdriver! Remove the latch! Turn the latch over and place it on the faceplate (a) so that you can press the insert leg (e) of the latch insert (d) under the... -
Page 13: Set Lock For Day Release Function (Assembler)
Installation Instructions Set lock for day release function (assembler) Set day release function Manufacture delivery state Lock Lock Remove the day release screw (2.5 mm Insert day release screw (2.5 mm hex hex socket) socket) Unlock Unlock If the day release function is set, the main latch is not actuated during motorised operation (door does not automatically jump open)! WINDOWS ·... -
Page 14: Assembly Day Release Element On The Lock (Assembler)
Installation Instructions Day release element assembly on the lock (assembler) Remove the faceplate cover. Position the day release element on the back of the faceplate (directly on the latch above the lock case) and push onto the lock case. Screw on the day release element with the attached TX20 M4x10 screw on the front of the faceplate! WINDOWS ·... -
Page 15: Assemble Maco Day Release Opener On Striker Plate (Assembler)
Installation Instructions MACO day release opener assembly on the striker plate (assembler) Remove the latch insert. Assemble the MACO day release opener. Activate the mechanical unlocking on the day release opener using the lever*. * Mechanical unlocking can remain activated as the day release function is controlled by the day release slider on the lock (see “Day Release Function" user manual, Page 16). WINDOWS ·... -
Page 16: Operating Instructions Day Release (End Customer)
Press the handle so that the locking element and the multi-function latch are element and the multi-function latch are pulled in pulled in! Slide the day release slider upwards, Slide the day release slider downwards! release the handle! The A-TS basic function, automatic locking, is restored! WINDOWS · DOORS · SLIDING DOORS... -
Page 17: Positions
Installation Instructions Positions Position of latch and shootbolt striker Position of striker plate, multi-function plate latch with hook Pressure adjustment: +/- 2 mm with latch and shootbolt striker plate +/- 1.5 mm with MF-HO striker plate Positioning of notch faceplate = notch strike plate A rebate clearance of 10 - 14 mm must be kept in the installed state! WINDOWS ·... -
Page 18: Drilling And Milling Images
Drilling and milling images Lock case and multi-function latch with hook lock ≤2 42,5 ≤2 15,5 15,5 Notch faceplate 17,5 16,2 +0,2 - 0,1 12,2 +0,2 - 0,2 Lock case Proposed cable position for access solution WINDOWS · DOORS · SLIDING DOORS... -
Page 19: Latch And Shootbolt Striker Plate
Drilling and milling images Latch and shootbolt striker plate *Milling E-opener WINDOWS · DOORS · SLIDING DOORS... -
Page 20: Multi-Function Hook Striker Plate
Drilling and milling images Multi-function hook striker plate 2 MF-HO +726 -764 WINDOWS · DOORS · SLIDING DOORS... -
Page 21: Positioning Of The Striker Plates
Positioning of the striker plates 2 Multi-function latches with hook, standard K+730, 1-sash Single striker plate Lock Single piece door striker Motor für Comfortöffnung Motor für Comfortöffnung *für höhere FFH Abdeckstulpe verwenden! *für höhere FFH Abdeckstulpe verwenden! * Use faceplate strip cover for higher FFH! Drive for motorised opening WINDOWS ·... -
Page 22: Multi-Function Latch With Hook, Standard K+730, 2-Sash
Positioning of the striker plates 2 Multi-function latches with hook, standard K+730, 2-sash French casement drive gear Lock Finger operated door shootbolt Motor für Comfortöffnung *für höhere FFH Abdeckstulpe verwenden! * Use faceplate strip cover for higher FFH! Drive for motorised opening WINDOWS ·... -
Page 23: Multi-Function Latch With Hook, Low K+605, 1-Sash
Positioning of the striker plates 2 Multi-function latches with hook, Low K+605, 1-sash Single striker plate Lock Single piece door striker Motor für Comfortöffnung Motor für Comfortöffnung *für höhere FFH Abdeckstulpe verwenden! *für höhere FFH Abdeckstulpe verwenden! * Use faceplate strip cover for higher FFH! Drive for motorised opening WINDOWS ·... -
Page 24: Multi-Function Latch With Hook, Low K+605, 2-Sash
Positioning of the striker plates 2 Multi-function latches with hook, Low K+605, 2-sash French casement drive gear Lock Finger operated door shootbolt Motor für Comfortöffnung Motor für Comfortöffnung *für höhere FFH Abdeckstulpe verwenden! *für höhere FFH Abdeckstulpe verwenden! * Use faceplate strip cover for higher FFH! Drive for motorised opening WINDOWS ·... -
Page 25: Multi-Function Latch With Hook, High K+980, 1-Sash
Positioning of the striker plates 2 Multi-function latches with hook, High K+980, 1-sash Single striker plate Lock Single piece door striker Motor für Comfortöffnung Motor für Comfortöffnung * Use faceplate strip cover for higher FFH! *für höhere FFH Abdeckstulpe verwenden! *für höhere FFH Abdeckstulpe verwenden! Drive for motorised opening WINDOWS ·... -
Page 26: Multi-Function Latch With Hook, High K+980, 2-Sash
Positioning of the striker plates 2 Multi-function latches with hook, High K+980, 2-sash French casement drive gear Lock Finger operated door shootbolt Motor für Comfortöffnung *für höhere FFH Abdeckstulpe verwenden! * Use faceplate strip cover for higher FFH! Drive for motorised opening WINDOWS ·... -
Page 27: Lengthening/Shortening Of The A-Ts K+730
Lengthening/shortening of the A-TS K+730 Module without additional locking point Only possible with A-TS K+730 module! When using the lengthening or shortening faceplate, the standard eurogroove must be used! FFH 2150 – FFH 2650 Shortening faceplate pack Contents: 1 pc. fixing bolt FFH 1900 – with shortening faceplate and FFH 2400 deadbolt FFH 2150 –... -
Page 28: Module With Additional Locking Point
Extension of the A-TS K+730 Module with additional locking point Only possible with A-TS K+730 module! When using the A-TS intermediate faceplate module, the standard eurogroove must be used! FFH 2250 – FFH 3100 The A-TS intermediate FFH 1900 – faceplate module is delivered FFH 2400 with two pre-inserted fixing pins! Remove 1 of the fixing pins from the intermediate faceplate. -
Page 29: Opendoor Access Solutions
openDoor Access Solutions Overview 3-latch door lock with opening motor High security thanks to self-locking of steel hooks and locking latch Tamper-proof Control unit protected from unauthorised access Maximum comfort thanks to motorised release Plug & Play Simple, non-mistakable plug-in connection EASY mounting and de-mounting of the... -
Page 30: A-Ts Transponder Plus
Access Solutions A-TS Transponder Plus Plug & Play connector / Motor cable connection Power supply 12 - 24 V DC cable installation min. 1.5 A Tension release Motor to access solution connection Brown: motor operating Access solution: voltage minus -... -
Page 31: A-Ts Transponder Keypad And Touchkey
Access Solutions A-TS Transponder Keypad and Touchkey Plug & Play connector / Motor cable connection Power supply 12 - 24 V DC cable installation min. 1.5 A Motor to access solution connection Tension release Brown: motor operating Access solutions... -
Page 32: A-Ts Somfy Gu Controller
Access Solutions A-TS Somfy GU Controller Tension release Connections Motor cable connection 1 GND Power supply 12 - 24 V DC 2 V in +8 - 24V (DC) min. 1.5 A = supply power 3 IN COM 4 IN closed 5 IN double locked = Isolated free inputs (max. -
Page 33: Circuit Diagram Frame-Side
openDoor Access Solutions circuit diagram frame side 12 - 24V DC Plug & Play connector / min. 1.5 A cable installation Brown: motor operating voltage Transformer minus - Brown - White: motor operating voltage plus + White + Green: control voltage* minus - Yellow Control voltage * plus + Access solutions: Klawiatura Touchkey Transponder... -
Page 34: Circuit Diagram Button Impulse
openDoor Access Solutions circuit diagram button impulse Plug & Play connector / cable installation 12 - 24V DC min. 1.5 A Brown: motor operating voltage minus - White: motor operating voltage plus + Transformer Green: control voltage* minus - Brown - Yellow Control voltage * plus + White + * The control voltage is required for push-button (button impulse) and toggle switch (activation/... -
Page 35: Circuit Diagram Toggle Switch
openDoor Access Solutions circuit diagram toggle switch Plug & Play connector / cable installation 12 - 24V DC min. 1.5 A Brown: motor operating voltage minus - White: motor operating voltage plus + Transformer Green: control voltage* minus - Brown - Yellow Control voltage * plus + White + * The control voltage is required for push-button (button impulse) and toggle switch (activation/... -
Page 36: Milling Image Transponder Plus
openDoor Access Solutions milling image Transponder Plus WINDOWS · DOORS · SLIDING DOORS... -
Page 37: Milling Image Keypad / Touchkey Bt
openDoor Access Solutions milling image Keypad / Touchkey BT 39,5 39,5 WINDOWS · DOORS · SLIDING DOORS... -
Page 38: Milling Image Including Connector Plate And Motor
openDoor Access Solutions milling image including mounting plate and motor assembly ≤ 20** 15,5 Comfort opener motor Proposed cable position for access solution 16,2 +0,2 - 0,1 12,2 +0,2 - 0,2 * Control unit for openDoor Access Solutions, ** Cable channel for Comfort solution, *** Cable for openDoor Access Solutions WINDOWS ·... -
Page 39: Cable Transition For Opening Angle ≤ 110°, Pvc 12 Air
openDoor Access Solutions cable transition for opening angle ≤ 110°, PVC 12 air R8 at F-16 R10 at F-20 R8 at F-16 R10 at F-20 WINDOWS · DOORS · SLIDING DOORS... -
Page 40: Cable Transition For Opening Angle ≤ 180°, Pvc 12 Air
openDoor Access Solutions cable transition for opening angle ≤ 180°, PVC 12 air R8 at F-16 R10 at F-20 30 mm deep Due to the various hinge options and the resulting turning axes, the position of the cable tray (dimension X) and the cover plate (dimension Y) must be determined independently! WINDOWS ·... - Page 41 Notes WINDOWS · DOORS · SLIDING DOORS...
- Page 42 Notes WINDOWS · DOORS · SLIDING DOORS...
- Page 43 Notes WINDOWS · DOORS · SLIDING DOORS...
- Page 44 MACO PROTECT Satisfied? MAYER & CO We appreciate your BESCHLÄGE GMBH feedback@maco.eu Alpenstraße 173 Order No.757658 - Date: October 2018 A-5020 Salzburg All rights reserved and subject to change. Graphic source: MACO Tel.: +43 662 6196-0 DThis print document is revised regularly. The latest version is available at E-Mail: maco@maco.eu http://www.maco.eu/sites/assets/MacoDocs/757626/757658.pdf...