Table of Contents
Advertisement
Quick Links
VSS Nederland
Owner´s Manual
Cameras & Domes
GCA-B1322D
GCA-B0322D
GCA-B0325D
GCA-B0323D
GCA-B1322D.1.1.3.11.2010
© ASP AG
VSS Nederland B.V.
-
Telfordstraat 11m
Video Systems
1/3" Col/B&W Fixed Dome Camera, Vari-Focal
1/3" Col/B&W Fixed Dome Camera, Vari-Focal
1/3" Col/B&W Fixed Dome Camera, Vari-Focal, WDR
1/3" CCD Col/B&W Fixed Dome Camera w/ IR LED
-
8013 RL Zwolle
-
Tel.: +31 38 42 89 420
EN
-
Fax: +31 38 42 89 429
-
E-mail: info@vssnederland.nl
e
Advertisement
Table of Contents
Related Manuals for Grundig GCA-B1322D
Summary of Contents for Grundig GCA-B1322D
- Page 1 VSS Nederland Video Systems Owner´s Manual Cameras & Domes GCA-B1322D 1/3" Col/B&W Fixed Dome Camera, Vari-Focal GCA-B0322D 1/3" Col/B&W Fixed Dome Camera, Vari-Focal GCA-B0325D 1/3" Col/B&W Fixed Dome Camera, Vari-Focal, WDR GCA-B0323D 1/3" CCD Col/B&W Fixed Dome Camera w/ IR LED GCA-B1322D.1.1.3.11.2010...
-
Page 3: Table Of Contents
Content: 1. Available Versions 2. Important Safety Instructions 3. Package Contents 4. Installation 1. Parts Name 2. Base Installation 3. Connections 4. 3-Axis Gimbal Adjustment 5. Zoom & Focus Adjustment 5. OSD Menu 1. OSD Controls 2. Main menu 3. Camera Setup 4. -
Page 4: Important Safety Instructions
If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (GRUNDIG is not liable for problems caused by unauthorized modifications or attempted repair.) To prevent fire or electric shock, do not expose the inside of this device to rain or moisture. -
Page 5: Installation
4. Installation Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°C), or high humidity. Doing so may cause fire or electric shock. Keep out of direct sunlight and heat radiation sources. It may cause fire. Avoid aiming the camera directly towards extremely bright objects such as sun, as this may damage the CCD image sensor. -
Page 6: Base Installation
4.2. Base Installation 1. Open the dome cover ring at the marked position (e.g. with a flat screw driver). 2. There are three mounting holes on the Dome Base for installation of the unit in any place such as ceiling, wall and etc. Use the three mounting screws to affix the Dome Base to a sturdy surface. -
Page 7: Connections
4.3. Connections - Power connection: Requires DC 12V or AC 24V input depending on camera model. - All camera models are supplied with service monitor output on the camera module. A service monitor and control cable is included in the package. Note: To set up OSD menu externally, service monitor and control cable is required. -
Page 8: Axis Gimbal Adjustment
4.4. 3-Axis Gimbal Adjustment 1. Pan: Adjust the pan by turning it to the right or left by hand. 2. Tilt: Adjust the tilt by moving it up or down by hand. 3. Rotation: Adjust the rotation to the desired angle by hand. 4.5. -
Page 9: Main Menu
5.1.2. OSD Icons Exits the menu setting. Before you exit make sure you SAVE your settings, or select QUIT to cancel. Returns to the previous menu. Returns to the main menu. Use this to SAVE your settings of MASK AREA, PRIVACY ZONE and more. Once you saved your settings, they will remain even if you select QUIT in the menu. -
Page 10: Camera Setup
COMMUNICATION: Configures the settings regarding the RS-485 communication. SYSTEM INFO: Displays the system information including the camera version and communication settings. LANGUAGE: Select a preferred language from those listed. 5.3. Camera Setup CAMERA ID [OFF, ON] : It is used to switch on/off the camera id. If camera id is switched ON you can access the CAMERA ID menu to programm the camera text. - Page 11 - If the IRIS menu is set to ELC, the electronic shutter will control the brightness so the SENS-UP function cannot be set to FIX mode, but to OFF or AUTO mode. - If the SHUTTER menu is set to AUTO, the SENS-UP menu can be set to either OFF or AUTO mode.
- Page 12 DETAIL [0~3] : Controls the horizontal or vertical distinction. V-SYNC [INT] : This camera model is fixed INT (Internal syncronization). AGC COLOR SUP [LOW, MID, HIGH] : Adjust the color scheme according to the AGC value. REVERSE [OFF, H/V, H/V] : Mirrors video signals horizontally, vertically, or both.
- Page 13 5.3.2. ALC (Automated Light Control) If you press the SETUP key with an ALC based submenu selected, you will see LENS, LEVEL, BACKLIGHT options on your screen. In the LENS options, you must select DC for this camera model. In the LEVEL option, you can adjust the overall brightness where “+”...
- Page 14 5.3.3. ELC (Electronic Light Control) If you press the SETUP key when the ELC submenu is selected, the corresponding screen appears. You can make the ELC function active or not. Similar to ALC setting, you can specify the BLC area. 5.3.4.
- Page 15 5.3.6. DAY/NIGHT (NIGHT MENU) If set to NIGHT, it will be fixed to BLACK and WHITE mode regardless of the ambient conditions. If you press the SETUP key with a NIGHT submenu selected, you will see a menu where you can set Burst to OFF/ON. If BURST is set to ON, the Burst signal will output together with the BLACK and WHITE composite video signal.
- Page 16 5.3.8. WHITE BALANCE - DAY: In this mode, you can set the colour values of RED and BLUE. The screen will be displayed in colours according to your settings. Note: - You can set the values of R-GAIN and B- GAIN only in AWC mode.
-
Page 17: Intelligence
5.3.9. DIGITAL ZOOM You can set the digital zoom factor and position. When the zoom factor and position are defined, the digital zoom function will operate. - RATIO: Define the zoom factor with the direction keys (< >). - LOCATION: If you press the SETUP key you can change the position of the digital zoom with the direction keys (<... -
Page 18: Privacy Zone
5.4.1. MASK AREA Specify a detection exception area to mask. Select a mask number and specify the size and position. Note: - If BACKLIGHT is set to BLC, the MASK AREA function will be deactivated. 5.5. Privacy Zone The PRIVACY function will protect your privacy by screening the privacy area that you have specified during monitoring. -
Page 19: Other Set
You can specify a pixel that moves as you change the PIXEL LEVEL to set the position. How to set the point: You can set each position of the 4 points. - If you press the SETUP key in <POINT>, you will see the points available in the PRIVACY ZONE. -
Page 20: Communication
5.7. Communication Configure the settings regarding the UART communication. **This related function is not available in this camera version. 5.8. System Info You can view the system information including the type, protocol, address, baud rate, serial number, and camera version. 5.9. - Page 21 Specifications GCA-B1322D Product available January 2011 Image Sensor 1/3" CCD (Sony Super HAD IT) Image Size Pixel Total: 795 x 596, Pixel Effective: 752 x 582 Resolution 600 (H) lines Col/B&W Auto (Electrical) / Color / B/W Sensitivity 0.4 Lux(50IRE) @ F1.2, 0.001 Lux (15IRE, Sens up x256)
- Page 22 Power Consumption 2.5 W Weight 0.32 kg Dimensions (wxhxd) Ø 122 x 95 mm Specifications GCA-B0325D Image Sensor 1/3" CCD (Sony PS Super HAD with WDR) Scanning System PAL, 50Hz, 625 TVL(V), 2:1 Inter Line Transfer Resolution 600(H) lines colour, 640 (H) lines b&w Col/B&W On/Off/Auto/Ext, IR-cut filter removable (ICR) Sensitivity Colour...
- Page 23 Dimensions English...
- Page 24 EC Declaration of Conformity GCA-B1322D 1/3" Col/B&W Fixed Dome Camera, Vari-Focal GCA-B0322D 1/3" Col/B&W Fixed Dome Camera, Vari-Focal GCA-B0325D 1/3" Col/B&W Fixed Dome Camera, Vari-Focal, WDR GCA-B0323D 1/3" CCD Col/B&W Fixed Dome Camera w/ IR LED It is hereby certified that the products meet the standards in the following relevant...