1. Manuals
  2. Brands
  3. AZZA Manuals
  4. Motherboard
  5. PT-5IT
  6. Operation manual

AZZA PT-5IT Operation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

PT-5IT
SYSTEM BOARD
( VER. 1.x )
OPERATION MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PT-5IT and is the answer not in the manual?

Questions and answers

Related Manuals for AZZA PT-5IT

Summary of Contents for AZZA PT-5IT

  • Page 1 PT-5IT SYSTEM BOARD ( VER. 1.x ) OPERATION MANUAL...

  • Page 2: Table Of Contents

    1. INTRODUCTION ....................1 SYSTEM OVERVIEW................1 FEATURES....................1 2. SPECIFICATIONS ....................1 3. SYSTEM BOARD LAYOUT ................1 PT-5IT VER. 1.x..................1 4. HARDWARE SETUP ................... 2 UNPACKING ....................2 HARDWARE CONFIGURATION............2 4.2.1 DRAM INSTALLATION................2 4.2.2 L2 CACHE MEMORY INSTALLATION..........3 4.2.3 CONNECTORS....................
  • Page 3 PT-5IT SYSTEM BOARD TRADEMARKS All trademarks used in this manual are the property of their respective owners. NOTE The “LOAD SETUP DEFAULTS” function loads the default settings directly from BIOS default table, these default settings are the best-case values that should optimize system performance and increase system stability .

  • Page 4: Introduction

    INTRODUCTION SYSTEM OVERVIEW The PT-5IT Pentium PCI Local Bus system board is designed based on the Intel 82430TX PCIset system chipset and Winbond I/O chipset, which built-in two channels PIO and Bus Master Enhanced PCI IDE port, one Floppy Disk control port, two high speed Serial ports (UARTs) and one multimode Parallel prot and also supports IR and USB ports.
  • Page 5 PT-5IT INTRODUCTION SYSTEM BOARD I/O ports : Supports two high speed serial ports (UARTs), One multimode parallel port for standard (SPP), enhanced (EPP) and high speed (ECP) modes. One Floppy Disk Control port. IR Port : Supports IR (Infrared Rays) functions. Both HPSIR and ASKIR are supported.

  • Page 6: Specifications

    PT-5IT SPECIFICATIONS SYSTEM BOARD SPECIFICATIONS Chipset Intel 82439TX, 82371AB and Winbond W83977TF. Intel : Pentium processor and OverDrive processor (P54C / P54CS / P54CTB / P55C) 75 / 90 / 100 / 120 / 133 / 150 / 166 / 180 / 200 / 233 MHz.
  • Page 7 PT-5IT SPECIFICATIONS SYSTEM BOARD IDE Ports Two channel PIO and Bus Master PCI IDE ports, maximum could be connected to 4 IDE Hard Disk and ATAPI CD-ROM device. Supports up to Mode 4 timing, and up to 22 MBytes/s transfer rates and supports Ultra DMA 33 mode transfers up to 33MBytes/sec.

  • Page 8: System Board Layout

    PT-5IT HARDWARE SETUP SYSTEM BOARD SYSTEM BOARD LAYOUT PT-5IT VER. 1.x Explanation : ll connectors, jumpers and components which marks by a black point on the corner means the pin-1 side of the connector, jumper and component. CN13 CN12 CN11...

  • Page 9: Hardware Setup

    3-1.) DRAM INSTALLATION The PT-5IT system board will support two banks main memory (bank0 and bank 1) on board, (using four 72-Pin SIMM socket, SIMM 1 - 4 and two 168-pin DIMM socket, DIMM 1 - 2) each bank could be single-sided or double-sided, 8MB up to 256 MB of local memory can be attained.

  • Page 10: L2 Cache Memory Installation

    Note : We strong recommend, Don't install 5V SIMM module and 3.3V DIMM modules at the same time. L2 CACHE MEMORY INSTALLATION The PT-5IT system board will support 256KB or 512KB cache memory on board, using synchronous pipeline-burst SRAMs. Both Write Back and Write Through cache update policy are supported.

  • Page 11: Connectors

    PT-5IT HARDWARE SETUP SYSTEM BOARD CONNECTORS A connector is two or more pins that are used make connections to the system standard accessories (such as power, mouse, printer,...etc.) The following is a list of connectors on board, as well as descriptions of each individual connector.
  • Page 12 PT-5IT HARDWARE SETUP SYSTEM BOARD (I) CN8 Parallel Port connector (Supports SPP/EPP/ECP mode, selected by BIOS setup,using IRQ7 or IRQ5, ECP using DMA channel 3 or 1) 1 14 Pin # Assignment Pin # Assignment STROBE- AUTO FEED- Data Bit 0...
  • Page 13 PT-5IT HARDWARE SETUP SYSTEM BOARD (K) CN10 COM A (Serial Port 1) connector COM1/2/3/4, selected by BIOS setup, using IRQ4 or 3 Pin # Assignment Pin # Assignment DCD (Data Carrier Detect) 2 (Received Data) (Transmit Data) DTR (Data Terminal...
  • Page 14 PT-5IT HARDWARE SETUP SYSTEM BOARD Pullup (+5V DC) Signal Pin (S) TS Turbo Switch connector (This function is reserved) Pin # Assignment Pin1&2 Function Turbo Control Open Turbo Ground Short Normal (T) SPEAKER Speaker connector Pin # Assignment Pin # Assignmen...

  • Page 15: Jumpers

    PT-5IT HARDWARE SETUP SYSTEM BOARD JUMPERS A jumper is two, three or more pins which may or may not be covered by a plastic connector plug (mini-jumper). A jumper is used to select different system options. Please make sure all jumpers at correct position before this system board used.
  • Page 16 PT-5IT HARDWARE SETUP SYSTEM BOARD (3) AMD K5 /K6 CPUs CPU Type Remark AMD-K5-PR75 open open AMD-K5-PR90 open open AMD-K5-PR100 open open AMD-K5-PR120 open open AMD-K5-PR133 open open AMD-K5-PR150 short short AMD-K5-PR166 short short AMD-K6-PR166 short short AMD-K6-PR200 open short...
  • Page 17 PT-5IT HARDWARE SETUP SYSTEM BOARD (D) JP13 ROM BIOS selection Pin # Function for +5V FLASH ROM for +12V FLASH ROM (E) JP2,JP3 DIMM voltage selection Pin # Function +5V DC +3.3V DC (Factory default)

  • Page 18: Award Bios Setup

    AWARD BIOS SETUP GETTING STARTED When the system is first powered on or reset, the BIOS will enter the Power-On Self Test routines ( POST : Display a copyright message on the screen followed by a diagnostics and initialization procedure.) (If an EGA or VGA card is installed, the copyright message of the video card maybe displayed on the screen first.) The BIOS will indicate any error or malfunction by a series of beeps or display the error message on screen.

  • Page 19: Main Menu

    PT-5IT AWARD BIOS SETUP SYSTEM BOARD To execute the Award BIOS Setup program, press DEL key. The simulate screen in figure 5-2 MAIN MENU will be displayed at this time. MAIN MENU ROM PCI / ISA BIOS (2A59IXXX) CMOS SETUP UTILITY AWARD SOFTWARE, INC.

  • Page 20: Standard Cmos Setup

    PT-5IT AWARD BIOS SETUP SYSTEM BOARD : Retrieves the previous CMOS values from CMOS, only for the current option page setup menu. : Loads the SETUP default values from BIOS default table, only for the current option page setup menu.

  • Page 21: Bios Features Setup

    PT-5IT AWARD BIOS SETUP SYSTEM BOARD : For IDE hard disks size larger then 528MB and up to 8.4GB (Giga Bytes) that use Logic Block Addressing (LBA) mode. Large : For IDE hard disks size larger then 528MB that do not use LBA mode.
  • Page 22 PT-5IT AWARD BIOS SETUP SYSTEM BOARD This feature flashes on the screen. During and after the system boots up, any attempt to write to the boot sector or partition table of the hard disk drive will halt the system and an error message will appear, in the mean time, you can run anti-virus program to locate the problem.

  • Page 23: Chipset Features Setup

    PT-5IT AWARD BIOS SETUP SYSTEM BOARD CHIPSET FEATURES SETUP ROM PCI / ISA BIOS (2A59IXXX) CHIPSET FEATURES SETUP AWARD SOFTWARE, INC. Auto Configuration Enabled DRAM Timing : 60 ns DRAM Leadoff Timing : 10/6/3 DRAM Read Burst (EDO/FP) : x222/x333...

  • Page 24: Power Management Setup

    PT-5IT AWARD BIOS SETUP SYSTEM BOARD POWER MANAGEMENT SETUP ROM PCI / ISA BIOS (2A59IXXX) POWER MANAGEMENT SETUP AWARD SOFTWARE, INC. Power Management User Define ** Reload Global Timer Events ** PM Control by APM : Yes IRQ[3-7 , 9-15] , NMI...
  • Page 25 PT-5IT AWARD BIOS SETUP SYSTEM BOARD ROM PCI / ISA BIOS (2A59IXXX) PNP/PCI CONFIGURATION AWARD SOFTWARE, INC. PNP OS Installed PCI IDE IRQ Map To : PCI-AUTO Resources Controlled By : Manual Primary IDE INT# Reset Configuration Data : Disabled...
  • Page 26 PT-5IT AWARD BIOS SETUP SYSTEM BOARD Disabled : The system BIOS will do nothing. Enabled : The system BIOS will clear/reset the ESCD during "POST". After clearing ESCD, the system BIOS will then change this item's value back to "Disable", otherwise, the ESCD will become useless.
  • Page 27 PT-5IT AWARD BIOS SETUP SYSTEM BOARD PnP device : Device that has Plug & Play compatibility. That means it can request for DMA, IRQ, I/O and Memory from the PnP BIOS and all these requests can be relocatable. In other words, these devices does not utilized any fixed resources.

  • Page 28: Integrated Peripherals

    PT-5IT AWARD BIOS SETUP SYSTEM BOARD INTEGRATED PERIPHERALS ROM PCI / ISA BIOS (2A59IXXX) INTEGRATED PERIPHERALS AWARD SOFTWARE, INC. IDE HDD Block Mode Enabled IDE Primary Master PIO : Auto IDE Primary Slave PIO : Auto Onboard Parallel Port : 378 / IRQ7...
  • Page 29 PT-5IT AWARD BIOS SETUP SYSTEM BOARD LOAD SETUP DEFAULTS This option loads the SETUP default values from BIOS default table. By pressing "Enter" key, while "LOAD SETUP DEFAULTS" is highlighted, then presses "Y" and "Enter" key. the SETUP default values will be loaded. The SETUP default settings are the best-case values that should optimize system performance and increase system stability.
  • Page 30 PT-5IT AWARD BIOS SETUP SYSTEM BOARD "Y" and "Enter" key, the setup program will be terminated and the system will be reboot.
  • Page 31 Printed in Taiwan Edition : 4 / 14 / 97...

Table of Contents