1. Manuals
  2. Brands
  3. AZZA Manuals
  4. Motherboard
  5. PT-5ITB
  6. Operation manual

AZZA PT-5ITB Operation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
PT-5ITB
SYSTEM BOARD
(VER. 1.x)
OPERATION MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PT-5ITB and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for AZZA PT-5ITB

Summary of Contents for AZZA PT-5ITB

  • Page 1 PT-5ITB SYSTEM BOARD (VER. 1.x) OPERATION MANUAL...

  • Page 2: Table Of Contents

    1. INTRODUCTION ....................1-1 1.1 SYSTEM OVERVIEW .................. 1-1 2. SPECIFICATIONS ....................2-1 3. SYSTEM BOARD LAYOUT ................3-1 3.1 PT-5ITB VER. 1.x ..................3-1 4. HARDWARE SETUP ..................4-1 4.1 UNPACKING....................4-1 4.2 HARDWARE CONFIGURATION.............. 4-1 4.2.1 CONNECTORS ..................4-2 4.2.2 JUMPERS....................
  • Page 3 PT-5ITB SYSTEM BOARD TRADEMARDKS All trademarks used in this manual are the property of their respective owners. NOTE The “LOAD SETUP DEFAULTS” function loads the default settings directly from BIOS default table, these default settings are the best-case values that will optimize system performance and increase system stability.

  • Page 4: Introduction

    1. INTRODUCTION 1.1 SYSTEM OVERVIEW The PT-5ITB Pentium PCI Local Bus system mainboard is designed based on AT form-factor on the Intel 82430TX PCIset system chipsets and Winbond I/O chipset, which built-in two channels PIO and Bus Master Enhanced PCI IDE port, one Floppy Disk...

  • Page 5: Specifications

    PT-5ITB SPECIFICATIONS SYSTEM BOARD 2. SPECIFICATIONS ¨ Chipset Intel 82430TX (82439TX (MTXC), 82371AB(PIIX4)) and Winbond W83977TF-A (- AW / ATF-AW). ¨ CPU (Jumper free) Intel : Pentium processor and OverDrive processor (P54C / P54CS / P54CTB / P55C) 90 / 100 / 120 / 133 / 150 / 166 / 200 / 233 MHz.
  • Page 6 PT-5ITB SPECIFICATIONS SYSTEM BOARD ¨ ACPI (For ATX Power) 1.Power on by Panel-Switch, or Modem Ring-In. 2.Power on by Keyboard, PS/2 Mouse, or LAN Signal. (optional) 3.Power off (Soft-off) by OS or Panel-Switch. ¨ WOL (optional) One WOL connector supports Wake-On-LAN (For ATX Power).
  • Page 7 PT-5ITB SPECIFICATIONS SYSTEM BOARD ¨ Software compatibility MS-DOS, Windows NT, OS/2, UNIX, NOVELL, Windows, Windows 95, CAD/CAM, Memphis (Beta 2), ...etc, full tested. ¨ DIMENSION Width & Length : 220 mm x 231 mm. Height : 3/4 inches with components mounted.

  • Page 8: System Board Layout

    PT-5ITB SYSTEM BOARD LAYOUT SYSTEM BOARD 3. SYSTEM BOARD LAYOUT 3.1 PT-5ITB VER. 1.x Explanation : All connectors, jumpers and components which are marked by a black point on the corner means the pin-1 side of the connector, jumper and component.

  • Page 9: Hardware Setup

    Before the system board is ready for operating, the hardware must be configured to make sure it will work properly with different environment. To configure the PT-5ITB system board is a simple task, only a few jumpers, connectors, cables and sockets needs to be selected and installed.

  • Page 10: Connectors

    PT-5ITB HARDWARE SETUP SYSTEM BOARD 4.2.1 CONNECTORS A connector is two or more pins that are used make connections to the system standard accessories (such as power, mouse, printer,...etc.). The following is a list of connectors on board, as well as descriptions of each individual connector.
  • Page 11 PT-5ITB HARDWARE SETUP SYSTEM BOARD (E) CN4 AT Power connector Pin # Assignment Power Good +5V DC +12V DC -12V DC Ground Ground Ground Ground -5V DC 10 G +5V DC 11 G +5V DC 12 G +5V DC (F) CN5...
  • Page 12 PT-5ITB HARDWARE SETUP SYSTEM BOARD (G) CN6 ATX Power connector Pin # Assignment Pin # Assignment +3.3V DC +3.3V DC Ground +5V DC Ground +5V DC Ground PW_OK +5V DC +12V DC +3.3V DC -12V DC Ground PS-ON Ground Ground...
  • Page 13 PT-5ITB HARDWARE SETUP SYSTEM BOARD (K) CN10 IDE 2 connector (Secondary IDE Port, using IRQ15) (L) CN11 Parallel Port Connector (Supports SPP/EPP/ECP mode, using IRQ7 or IRQ5, ECP using DMA channel 3 or 1, selected by CMOS setup) 1 14...
  • Page 14 PT-5ITB HARDWARE SETUP SYSTEM BOARD (P) CN14 Consumer IR connector (optional and available only while U10 using W83977ATF I/O Chip) Pin # Assignment +5V DC IR Transmit Consumer IR Receive Ground (Q) CN15 SB-LINK connector (For PCI bus sound cards. Such as Creative Labs EMU8008 sound chip)
  • Page 15 PT-5ITB HARDWARE SETUP SYSTEM BOARD (T) CN18 USB Port 2 (Universal Serial Bus port 2) connector Pin # Assignment +5V DC (RED WIRE) DATA- (WHITE WIRE) DATA+ (GREEN WIRE) Ground (BLACK WIRE) Ground (BLACK WIRE) (U) KEYLOCK Front Panel Power LED & Key-Lock connector...
  • Page 16 PT-5ITB HARDWARE SETUP SYSTEM BOARD (Y) TL Turbo LED connector Pin # Assignment Pin # Assignment Pullup (+5V DC) Ground (Z) SL Sleep LED connector ATX Power Off : LED Turn On ATX Power On : LED Turn Off Pin # Assignment...

  • Page 17: Jumpers

    PT-5ITB HARDWARE SETUP SYSTEM BOARD 4.2.2 JUMPERS A jumper is two, three or more pins which may or may not be covered by a plastic connector plug (mini-jumper). A jumper is used to select different system options. Please make sure all jumpers at correct position before this system board used.
  • Page 18 PT-5ITB HARDWARE SETUP SYSTEM BOARD (5) 75MHz x 2 (6) 60MHz x 2.5 JUMPERS CPU TYPE JUMPERS CPU TYPE 1 2 3 1 2 3 Intel 80502-150 ¡ ¡ G JP1 ¡ ¡ G JP1 ¡ ¡ ¡ ¡ G JP2 ¡...
  • Page 19 PT-5ITB HARDWARE SETUP SYSTEM BOARD (11) 75MHz x 3 (12) 60MHz x4 JUMPERS CPU TYPE JUMPERS CPU TYPE 1 2 3 1 2 3 ¡ ¡ G JP1 ¡ ¡ G JP1 ¡ ¡ ¡ ¡ G JP2 ¡ ¡...
  • Page 20 PT-5ITB HARDWARE SETUP SYSTEM BOARD (B) JP8, JP9, JP10, JP11, JP12 CPU CORE voltage selection (for Jumpers Setting or Jumper free) NOTE : The CPU CORE voltage for Jumper free support 2.1V, 2.8V, 2.9V, 3.2V, 3.4V, 3.5V DC only, so if your CPU CORE voltage os not these voltage, please use those JP11, JP12, JP13, JP14, JP15 to set the correct CPU CORE voltage.
  • Page 21 PT-5ITB HARDWARE SETUP SYSTEM BOARD JUMPERS CORE Voltage IO Voltage CPU TYPE REMARKS 3.3V 3.3V IDT C6 For Jumpers ¡ ¡ JP11 Sitting ¡ ¡ JP12 ¡ ¡ JP13 1 G G JP14 ¡ ¡ JP15 JUMPERS CORE Voltage IO Voltage...
  • Page 22 PT-5ITB HARDWARE SETUP SYSTEM BOARD JUMPERS CORE Voltage IO Voltage CPU TYPE REMARKS 2.9V 3.3V AMD K6/PR2-166 ¡ ¡ JP11 2.9V 3.3V AMD K6/PR2-200 Jumper free ¡ ¡ JP12 2.9V 3.3V Cyrix 6x86MX 1 G G JP13 1 G G JP14 ¡...
  • Page 23 PT-5ITB HARDWARE SETUP SYSTEM BOARD JUMPERS CORE Voltage IO Voltage CPU TYPE REMARKS 2.5V 3.3V ¡ ¡ JP11 Jumpers 1 G G JP12 Setting ¡ ¡ JP13 1 G G JP14 ¡ ¡ JP15 JUMPERS CORE Voltage IO Voltage CPU TYPE REMARKS 2.4V...
  • Page 24 PT-5ITB HARDWARE SETUP SYSTEM BOARD JUMPERS CORE Voltage IO Voltage CPU TYPE REMARKS 2.1V 3.3V ¡ ¡ JP11 Jumper free 1 G G JP12 1 G G JP13 1 G G JP14 ¡ ¡ JP15 JUMPERS CORE Voltage IO Voltage...

  • Page 25: Installing A Cpu In The Zif Socket

    PT-5ITB HARDWARE SETUP SYSTEM BOARD 4.3 INSTALLING A CPU IN THE ZIF SOCKET The Intel Socket 7 incorporated in the mainboard specifications, is specially designed for the Pentium processor. While inserting the Pentium processor onto Socket 7, certain precautionary steps must be followed. The following diagrams of demonstration and explanation are worth of your note.
  • Page 26 PT-5ITB HARDWARE SETUP SYSTEM BOARD 3.Press the lever down. The plate will slide forward. You will feel some resistance as the pressure starts to secure the CPU in the socket. When the CPU is installed, the lever should snap into place at the side of the socket.

  • Page 27: Installation Of Cpu Cooling Fan

    PT-5ITB HARDWARE SETUP SYSTEM BOARD 4.4 INSTALLATION OF CPU COOLING FAN Improper installation of CPU cooling fan will cause serious damage to the motherboard. Please follow the procedures carefully: 1.There is a metal clip attached to the CPU cooler as shown below.

  • Page 28: Upgrading System Memory

    4.Push down the opposite side of the metal clip firmly and carefully to lock the cooler in place. 4.5 UPGRADING SYSTEM MEMORY The PT-5ITB mainboard can use up to four 72-pin SIMM sockets (SIMM1, SIMM2, SIMM3, SIMM4), and two 168-pin DIMM sockets(DIMM1, DIMM2). Upgradable from 8MB to 256MB.

  • Page 29: Installing A Dimm Module

    PT-5ITB HARDWARE SETUP SYSTEM BOARD Press it forward onto the positioning pins. The retaining clips should fit over the edge and hold the SIMM in place. 4.5.2 Installing a DIMM Module Insert the DIMM module into the socket at an angle.

  • Page 30: Memory Module Installing

    PT-5ITB HARDWARE SETUP SYSTEM BOARD 2.Put out the DIMM module from the DIMM socket. Press Press down down 4.5.3 Memory Module Installing The speed of FPM DRAMs must be used 70ns or faster than 70ns, the speed of EDO DRAMs and SDRAMs must be used 60ns or faster than 60ns.
  • Page 31 PT-5ITB HARDWARE SETUP SYSTEM BOARD Bank 0 Bank 1 SIMM1 and SIMM2 DIMM1 SIMM3 and SIMM4 DIMM2 Single-sided Empty Single-sided Empty Double-sided Empty Double-sided Empty Empty Single-sided Empty Single-sided Empty Double-sided Empty Double-sided Note : We strong recommend, don‘t install 5V SIMM module and 3.3V DIMM module at the same time.

  • Page 32: Award Bios Setup

    PT-5ITB AWARD BIOS SETUP SYSTEM BOARD 5. AWARD BIOS SETUP 5.1 GETTING STARTED When the system is first powered on or reset, the BIOS will enter the Power-On Self Test routines ( POST : Display a copyright message on the screen followed by a diagnostics and initialization procedure.) (If an EGA or VGA card is installed, the copyright message...

  • Page 33: Main Menu

    PT-5ITB AWARD BIOS SETUP SYSTEM BOARD After the POST routines are completed, the following message appears : “ Press DEL to enter SETUP ” To execute the Award BIOS Setup program, press DEL key. The simulate screen in figure 5-2 MAIN MENU will be displayed at this time.

  • Page 34: Standard Cmos Setup

    PT-5ITB AWARD BIOS SETUP SYSTEM BOARD Arrow Keys : Use the arrow keys to move the cursor to the desired item. Enter : To select the desired item. : Display the help screen for the selected feature. (Shift)F2 : To change the screen color, total 16 colors.
  • Page 35 PT-5ITB AWARD BIOS SETUP SYSTEM BOARD MODE: For IDE hard disks, this BIOS provides three modes to support both normal size IDE hard disks and also disks size larger the 528MB : l NORMAL : For IDE hard disks size smaller then 528MB.

  • Page 36: Bios Features Setup

    PT-5ITB AWARD BIOS SETUP SYSTEM BOARD 5.5 BIOS FEATURES SETUP ROM PCI / ISA BIOS (2A59IXXX) BIOS FEATURES SETUP AWARD SOFTWARE, INC. Virus Warning Disabled Video BIOS Shadow : Enabled CPU Internal Cache : Enabled C8000-CBFFF Shadow : Disabled External Cache...

  • Page 37: Chipset Features Setup

    PT-5ITB AWARD BIOS SETUP SYSTEM BOARD CPU Internal Cache : This option enables CPU‘s internal (L1) cache memory. If you want to use the internal (L1) cache memory and external (L2) cache memory, this option must be enabled. External Cache : This option enables L2 (secondary) external cache memory.
  • Page 38 PT-5ITB AWARD BIOS SETUP SYSTEM BOARD NOTE : CPU Type : IDT-C6 CPU Vcore: 3.5V CPU Speed: 180 (60*3) For IDT-C6 CPU, the BIOS only supports 3.5V, so if your IDT-C6 CPU Vcore voltage is not 3.5V DC, please refer to this manual the page 4-13, to set the correct CPU Vcore voltage.

  • Page 39: Power Management Setup

    PT-5ITB AWARD BIOS SETUP SYSTEM BOARD 5.7 POWER MANAGEMENT SETUP ROM PCI / ISA BIOS (2A59IXXX) POWER MANAGEMENT SETUP AWARD SOFTWARE, INC. Power Management User ** Reload Global Timer Events ** Define PM Control by APM : Yes IRQ[3-7 , 9-15], NMI...

  • Page 40: Pnp/Pci Configuration

    PT-5ITB AWARD BIOS SETUP SYSTEM BOARD 5.8 PNP/PCI CONFIGURATION ROM PCI / ISA BIOS (2A59IXXX) PNP/PCI CONFIGURATION AWARD SOFTWARE, INC. PNP OS Installed PCI IDE IRQ Map To : PCI-AUTO Resources Controlled By : Manual Primary IDE INT# Reset Configuration Data : Disabled...
  • Page 41 PT-5ITB AWARD BIOS SETUP SYSTEM BOARD Reset Configuration Data : Disabled : The system BIOS will do nothing. Enabled : The system BIOS will clear/reset the ESCD during “POST”. After clearing the ESCD, the system BIOS will then change this item‘s value back to “Disable”, otherwise, the ESCD will become useless.

  • Page 42: Integrated Peripherals

    PT-5ITB AWARD BIOS SETUP SYSTEM BOARD Legacy device : Ÿ A legacy device is a device that all its resources are fixed by hardware (or selected by jumpers). Ÿ All ISA Non-PnP devices are legacy device. Extended System Configuration Data (ESCD) : Ÿ...

  • Page 43: Load Setup Defaults

    PT-5ITB AWARD BIOS SETUP SYSTEM BOARD Onboard Parallel Mode : This setting determines the onboard parallel port (CN11) transmission mode. Supports either SPP, EPP, ECP, or ECP+EPP. 5.10 LOAD SETUP DEFAULTS This option loads the SETUP default values from BIOS default table. By pressing “Enter”...

  • Page 44: Exit Without Saving

    PT-5ITB AWARD BIOS SETUP SYSTEM BOARD 5.15 EXIT WITHOUT SAVING This option exites setup routine without saving any changed values to CMOS RAM, by moving the cursor to “EXIT WITHOUT SAVING” and pressing “Enter” key, then types “Y” and Enter“ key, the setup program will be terminated and the system will be reboot.
  • Page 45 Printed in Taiwan Edition : 02 / 13 / 98...

Table of Contents